Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P2457  EGR Cooler "A" Efficiency Below Threshold  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2457 EGR Cooler "A" Efficiency Below Threshold Diagnosis Condition:
The conditions described below remain for 11 seconds or more.
·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.

·

In addition, the conditions described below remain for 40 seconds or more

·

The engine speed is 1,200 rpm or more.

·

Fuel injector quantity is 25 mm3/st or more.

·

The EGR gas flow rate is 10 kg/h or more.

·

A change in the engine speed is 664 rpm or less.

·

A change in fuel injection quantity is 78 mm3/st or less.

·

Atmospheric pressure is higher than 75 kPa.

·

Vehicle speed is 21 km/h (13 mph) or more.

·

Intake air quantity is 30 g/sec or more.

·

Intake air temperature is -10°C (14°F) or more.

·

Exhaust brake is not actuated.


Malfunction Status:
·

The calculated EGR cooler efficiency is less than 40%.

·

(Following are the values of difference between the calculated intake manifold air intake temperature and the actual intake manifold air intake temperature). If the EGR rate is 0%: the difference in temperature is less than40°C (104°F). If the EGR rate is 20%: the difference in temperature is less than 47°C (116.6°F). If the EGR rate is 60%: the difference in temperature is less than 90°C (194°F).

·

Judged when the calculated intercooler efficiencies are as follows. If the vehicle speed is 21 km/h (13 mph)the efficiency is higher than 45%. If the vehicle speed is 40 km/h (25 mph): the efficiency is higher than 65%.


Malfunction Duration:

1 second or more


·

Exhaust gas temperature sensor (for EGR cooler side)

·

EGR cooler sub-assembly

·

EGR control malfunction

·

Diesel throttle valve malfunction

·

Suction control valve malfunction

·

Injector malfunction


Class B2 DTC stored

MONITOR DESCRIPTION

The ECM detects abnormally high EGR gas temperatures by means of the exhaust gas temperature sensor (for EGR cooler side).

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2457 After warming up the engine, drive at an engine speed of 1200 rpm or higher


CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (EXHAUST GAS TEMPERATURE SENSOR (FOR EGR COOLER SIDE))
a.

Check the connection of the exhaust gas temperature sensor (for EGR cooler side) connector (looseness and poor contact).


Result:
Proceed to
OK
NG



OK

2.CHECK EXHAUST GAS TEMPERATURE SENSOR (FOR EGR COOLER SIDE)

NG

24.CONNECT SECURELY
2.CHECK EXHAUST GAS TEMPERATURE SENSOR (FOR EGR COOLER SIDE)
a.

Check the installation of the exhaust gas temperature sensor (for EGR cooler side).


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the exhaust gas temperature sensor (for EGR cooler side).


Result:
Proceed to
OK
NG



OK

3.INSPECT EXHAUST GAS TEMPERATURE SENSOR (FOR EGR COOLER SIDE)

NG

23.REPAIR OR REPLACE EXHAUST GAS TEMPERATURE SENSOR (FOR EGR COOLER SIDE)
3.INSPECT EXHAUST GAS TEMPERATURE SENSOR (FOR EGR COOLER SIDE)
a.

Inspect the exhaust gas temperature sensor (for EGR cooler side).


Result:
Proceed to
OK
NG



OK

4.CHECK COOLANT

NG

22.REPLACE EXHAUST GAS TEMPERATURE SENSOR (FOR EGR COOLER SIDE)
4.CHECK COOLANT
a.

Check the level and condition of the coolant in the coolant reservoir.


b.

Check the condition of the coolant pipe (clogging or leaks).


Result:
Proceed to
OK
NG



OK

5.CHECK EGR COOLER SUB-ASSEMBLY

NG

21.REPAIR OR REPLACE TROUBLE AREAS
5.CHECK EGR COOLER SUB-ASSEMBLY
a.

Check if soot is obstructing the inlet/outlet of the EGR cooler gas passageway.


b.

Check if there are foreign substances stuck to the EGR cooler coolant passageway.


c.

Check the EGR cooler coolant passageway for obstruction due to deformation or other damage.


d.

Check if coolant is leaking from the EGR cooler sub-assembly.


Result:
Proceed to
OK
NG



OK

6.CHECK EGR VALVE ASSEMBLY

NG

20.REPAIR OR REPLACE TROUBLE AREAS
6.CHECK EGR VALVE ASSEMBLY
a.

Check the EGR valve for damage due to intrusion of foreign substances.


b.

Check if the inlet/outlet of the exhaust gas passageway is obstructed by soot.


Result:
Proceed to
OK
NG



OK

7.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR VALVE POSITION)

NG

19.REPAIR OR REPLACE EGR VALVE ASSEMBLY
7.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR VALVE POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Valve Position / Data List / Actual EGR Valve Position and Target EGR Valve Position


d.

Check each step from 90 to 0% of the time lag of the target EGR valve opening and actual EGR valve opening.

NOTICE:

Perform the inspection while the engine is stopped to avoid engine damages.


Standard:

The response delay should be less than 5 seconds.



Result:
Proceed to
OK
NG



OK

8.CHECK DIESEL THROTTLE BODY

NG

18.REPLACE EGR VALVE ASSEMBLY
8.CHECK DIESEL THROTTLE BODY
a.

Remove the diesel throttle body from the vehicle and check that it does not catch or that there is no foreign matter pinched.

(Push and move the throttle valve by hand with no power supplied)


b.

Check that there is no looseness between the throttle valve and shaft.


Result:
Proceed to
OK
NG



OK

9.CHECK FUEL SYSTEM (CHECK DATA)

NG

17.REPLACE DIESEL THROTTLE BODY
9.CHECK FUEL SYSTEM (CHECK DATA)
a.

Save GTS data for use during the fuel system inspection. (Engine speed pattern)

i.

Connect the GTS to the DLC3.


ii.

After engine has reached operating temperature (more than 82°C (180°F)).


iii.

Check that the loads from the air conditioning, headlights, PTO, etc. are turned off.


iv.

Enter the following menus: Powertrain / Engine / Active Test / Control the Target Engine Speed / Data List / Engine Speed / Common Rail Pressure and Target Common Rail Pressure.


v.

Check that the loads from the air conditioning, headlights, PTO, etc. are turned off.



A447921E03
0.375,2.073 3.125,2.271 2.75,0.198 10 false Engine Speed (rpm) 1.25,1.833 1.792,2.104 0.542,0.271 10 false 750 1.177,1.615 1.719,1.885 0.542,0.271 10 false 1000 1.177,1.365 1.719,1.635 0.542,0.271 10 false 1500 1.177,1.042 1.719,1.313 0.542,0.271 10 false 2000 1.188,0.75 1.729,1.021 0.542,0.271 10 false 2500 0.208,0.125 2.823,0.542 2.615,0.417 10 false Engine speed pattern: 5.073,0.313 6.813,0.719 1.74,0.406 10 false Measure each engine speed for 20 seconds. 3.583,2.104 4.125,2.375 0.542,0.271 10 false Time

b.

Save GTS data for use during the fuel system inspection. (Acceleration pattern)

i.

Connect the GTS to the DLC3.


ii.

After engine has reached operating temperature (more than 82°C (180°F)).


iii.

Check that the loads from the air conditioning, headlights, PTO, etc. are turned off.


iv.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed, Common Rail Pressure, Target Common Rail Pressure and Target Accelerator Position.


v.

Idle and then run with no load at the highest speed for 20 seconds at a time. Repeat this at least 3 times and save the data.



A447922E02
0.052,2.271 2.063,2.552 2.01,0.281 10 false Target Accelerator Position 1.063,2.042 1.521,2.24 0.458,0.198 10 false 0 % 0.906,0.917 1.365,1.115 0.458,0.198 10 false 100 % 2.458,1.667 3.135,2.125 0.677,0.458 10 false 20 sec 3.167,1.656 3.844,2.115 0.677,0.458 10 false 20 sec 0.156,0.073 1.531,0.271 1.375,0.198 10 false Acceleration pattern: 2.333,0.396 5.792,0.729 3.458,0.333 10 false At least three times, repeating the Wide-Open Throttle

Result:
Proceed to
NEXT



NEXT

10.CHECK FUEL SYSTEM (CHECK DATA)
10.CHECK FUEL SYSTEM (CHECK DATA)
a.

Check the saved data.

i.

Engine speed pattern:

Pressure is reduced by 5 MPa or more continually for 5 seconds or more.

A447923E01
0.188,0.115 1.875,0.313 1.688,0.198 10 false Engine speed pattern: 3.115,2.083 3.698,2.313 0.583,0.229 10 false Time 5.688,0.948 6.708,1.354 1.021,0.406 10 false Target Common Rail Pressure 0.073,1.792 1.042,2.198 0.969,0.406 10 false Common Rail Pressure (MPa) 5.677,0.302 6.698,0.708 1.021,0.406 10 false Actual Common Rail Pressure

Replace:

Supply pump assembly



ii.

Engine speed pattern:

Pressure is increased by 5 MPa or more continually for 5 seconds or more.

A447924E02
0.188,0.115 1.875,0.313 1.688,0.198 10 false Engine speed pattern: 3.115,2.083 3.698,2.313 0.583,0.229 10 false Time 5.688,0.948 6.708,1.354 1.021,0.406 10 false Target Common Rail Pressure 0.073,1.792 1.042,2.198 0.969,0.406 10 false Common Rail Pressure (MPa) 5.688,0.365 6.708,0.771 1.021,0.406 10 false Actual Common Rail Pressure

Replace:

Suction control valve



iii.

Accelerator pattern:

The maximum common rail pressure exceeds 222 MPa for even a moment during pressure increase.

A447925E01
0.104,0.083 1.792,0.281 1.688,0.198 10 false Accelerator pattern: 3.115,2.083 3.698,2.313 0.583,0.229 10 false Time 5.688,0.948 6.708,1.354 1.021,0.406 10 false Target Common Rail Pressure 0.073,1.792 1.042,2.198 0.969,0.406 10 false Common Rail Pressure (MPa) 2.823,0.385 3.896,0.583 1.073,0.198 10 false 222 MPa 5.688,0.375 6.708,0.781 1.021,0.406 10 false Actual Common Rail Pressure

Replace:

Suction control valve



iv.

Accelerator pattern:

After the maximum common rail pressure exceeds 222 MPa during pressure increase, the actual rail pressure falls below the target rail pressure.

A447926E01
0.104,0.083 1.792,0.281 1.688,0.198 10 false Accelerator pattern: 3.25,2.073 3.833,2.302 0.583,0.229 10 false Time 5.688,0.948 6.708,1.354 1.021,0.406 10 false Target Common Rail Pressure 0.073,1.792 1.042,2.198 0.969,0.406 10 false Common Rail Pressure (MPa) 2.823,0.385 3.896,0.583 1.073,0.198 10 false 222 MPa 5.688,0.375 6.708,0.781 1.021,0.406 10 false Actual Common Rail Pressure

Replace:

Suction control valve



v.

Accelerator pattern:

Before the maximum common rail pressure exceeds 222 MPa during pressure increase, the actual rail pressure falls below the target rail pressure rapidly.

A447927E01
0.104,0.083 1.792,0.281 1.688,0.198 10 false Accelerator pattern: 3.25,2.073 3.833,2.302 0.583,0.229 10 false Time 5.688,0.948 6.708,1.354 1.021,0.406 10 false Target Common Rail Pressure 0.073,1.792 1.042,2.198 0.969,0.406 10 false Common Rail Pressure (MPa) 2.823,0.385 3.896,0.583 1.073,0.198 10 false 222 MPa 5.688,0.375 6.708,0.781 1.021,0.406 10 false Actual Common Rail Pressure

Replace:

Common rail assembly



vi.

Accelerator pattern:

The maximum common rail pressure exceeds 222 MPa during pressure drop.

A447928E01
0.104,0.083 1.792,0.281 1.688,0.198 10 false Accelerator pattern: 3.115,2.083 3.698,2.313 0.583,0.229 10 false Time 5.688,0.948 6.708,1.354 1.021,0.406 10 false Target Common Rail Pressure 0.073,1.792 1.042,2.198 0.969,0.406 10 false Common Rail Pressure (MPa) 3.375,0.385 4.448,0.583 1.073,0.198 10 false 222 MPa 5.688,0.375 6.708,0.781 1.021,0.406 10 false Actual Common Rail Pressure

Check:

Return pipe



vii.

Engine speed pattern:

The pressure is disturbed at a given speed and the pressure decreases at higher speed.

A447929E01
0.104,0.083 1.792,0.281 1.688,0.198 10 false Engine speed pattern: 3.115,2.083 3.698,2.313 0.583,0.229 10 false Time 5.688,0.948 6.708,1.354 1.021,0.406 10 false Target Common Rail Pressure 0.073,1.792 1.042,2.198 0.969,0.406 10 false Common Rail Pressure (MPa) 2.042,0.927 3.115,1.125 1.073,0.198 10 false 10 MPa 5.688,0.375 6.708,0.781 1.021,0.406 10 false Actual Common Rail Pressure 3.063,1.719 3.646,1.948 0.583,0.229 10 false 5 sec

Replace:

Supply pump assembly



viii.

Engine speed pattern:

Hunting remains within 10 MPa or more for more than 5 seconds.

A447930E01
0.104,0.083 1.792,0.281 1.688,0.198 10 false Engine speed pattern: 3.115,2.083 3.698,2.313 0.583,0.229 10 false Time 5.688,0.948 6.708,1.354 1.021,0.406 10 false Target Common Rail Pressure 0.073,1.792 1.042,2.198 0.969,0.406 10 false Common Rail Pressure (MPa) 2.042,0.927 3.115,1.125 1.073,0.198 10 false 10 MPa 5.688,0.375 6.708,0.781 1.021,0.406 10 false Actual Common Rail Pressure 3.063,1.719 3.646,1.948 0.583,0.229 10 false 5 sec

Replace:

Suction control valve



ix.

Accelerator pattern:

The engine stops during pressure relief.

A447931E01
0.104,0.083 1.792,0.281 1.688,0.198 10 false Accelerator pattern: 4.177,2.063 4.76,2.292 0.583,0.229 10 false Time 5.688,0.948 6.708,1.354 1.021,0.406 10 false Target Common Rail Pressure 0.073,1.792 1.042,2.198 0.969,0.406 10 false Common Rail Pressure (MPa) 3.281,0.375 4.354,0.573 1.073,0.198 10 false 222 MPa 5.688,0.375 6.708,0.781 1.021,0.406 10 false Actual Common Rail Pressure

Replace:

Suction control valve



x.

Target common rail pressure during idling deviates from the standard value.

Replace:

Suction control valve




b.

Check SCV actuation current value

i.

Connect the GTS to the DLC3.


ii.

After engine has reached operating temperature. (more than 82°C (180°F))


iii.

Check that the loads from the air conditioning, headlights, PTO, etc. are turned off.


iv.

Enter the following menus: Powertrain / Engine / Active Test / Control the Target Engine Speed / Data List / Engine Speed and Target Pump SCV Current


v.

Set the engine speed to 750 rpm, and then check the Target Pump SCV Current value.

A447932E02
0.115,2.094 1.635,2.708 1.521,0.615 10 false Target Pump SCV Current (mA) 1.771,0.438 3.76,0.635 1.99,0.198 10 false Target current value 4.781,0.708 6.771,0.906 1.99,0.198 10 false Average current value (30sec) 3.563,1.677 5.552,1.875 1.99,0.198 10 false Fluctuation in current value 5.688,2.146 6.406,2.479 0.719,0.333 10 false Time

Standard:
Item Condition Reference Value
Target Pump SCV Current Average current value 1660 to 1820 mA
Fluctuation in current value Below 80 mA




Result:
Proceed to
OK
NG



OK

11.READ VALUE USING GTS (INJECTION VOLUME AND ENGINE SPEED)

NG

16.REPAIR OR REPLACE TROUBLE AREAS
11.READ VALUE USING GTS (INJECTION VOLUME AND ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed and Injection Volume


d.

Read the value displayed on the GTS.


Standard:
Item Condition Reference Value
Engine Speed
·

Engine speed: 1500 rpm

·

Engine coolant temperature: 80°C or higher

·

Shift position N

·

A/C OFF

·

Air compressor OFF


Speed fluctuation amount is 15 rpm or less
Injection Volume 5 mm3/st or more


Result:
Proceed to
OK
NG



OK

12.CHECK DTC OUTPUT

NG

15.REPLACE INJECTOR ASSEMBLY
12.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P2457 is output A
DTCs are not output B




A

13.REPLACE ECM

B

END

13.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
14.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

15.REPLACE INJECTOR ASSEMBLY
a.

Replace the injector assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
16.REPAIR OR REPLACE TROUBLE AREAS
a.

Repair or replace the trouble areas.


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
17.REPLACE DIESEL THROTTLE BODY

Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
18.REPLACE EGR VALVE ASSEMBLY
a.

Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
19.REPAIR OR REPLACE EGR VALVE ASSEMBLY
a.

Remove foreign substances and clean the passageway.

HINT:

If damaged, replace the EGR valve assembly.



Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
20.REPAIR OR REPLACE TROUBLE AREAS
a.

Repair or replace the trouble areas.


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
21.REPAIR OR REPLACE TROUBLE AREAS
a.

Repair or replace the trouble areas.


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
22.REPLACE EXHAUST GAS TEMPERATURE SENSOR (FOR EGR COOLER SIDE)
a.

Replace the exhaust gas temperature sensor (for EGR cooler side).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
23.REPAIR OR REPLACE EXHAUST GAS TEMPERATURE SENSOR (FOR EGR COOLER SIDE)
a.

Repair or replace the exhaust gas temperature sensor (for EGR cooler side).


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
24.CONNECT SECURELY
a.

Connect securely the exhaust gas temperature sensor (for EGR cooler side) connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT