Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P2483  Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 5  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2483 Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 5 Diagnosis Condition:
Engine start
·

Difference of the temperature is within 8°C (46.4°F) between ambient temperature and coolant temperature.

·

Difference of the temperature is within 8°C (46.4°F) between urea temperature and ambient temperature.

·

Difference of the temperature is within 8°C (46.4°F) between coolant temperature and urea temperature.

·

At least 10 seconds has elapsed since engine was started.

·

Maximum coolant temperature at previous DCY is greater than 70°C (158°F).


Engine running
·

The time after the activation of a DPR regeneration is 300 seconds or more.

·

The engine revolution is 1000 rpm or more.

·

The time after the engine start is 10 seconds or more.

·

The fuel injection quantity is 10 mg/cylinder/sec or more.

·

The value of the mass air flow meter is 300 kg/h or more.

·

The value of the No. 5 exhaust gas temperature sensor is 150°C (302°F) or more (Low) or below 350°C (662°F) (Lo).


Malfunction Status:
Engine start

Difference between the No. 5 exhaust gas temperature sensor and ambient temperature is higher than 100°C (212°F).


Engine running

Reference of High side:

The value of the No. 5 exhaust gas temperature sensor difference between sensor and calculated continues to be threshold or more for 10 seconds or more.

Reference of Lo side:

The value of the No. 5 exhaust gas temperature sensor difference between sensor and calculated continues to be threshold or more for 10 seconds or more.


Malfunction Duration:

1 second or more


Engine start:
·

No. 5 exhaust gas temperature sensor

·

Harness or connector

·

ECM

·

Ambient air temperature sensor

·

Coolant temperature sender

·

Urea pump (Urea temperature sensor)


Engine running:
·

No. 5 exhaust gas temperature sensor

·

Harness or connector

·

ECM

·

No. 4 exhaust gas temperature sensor

·

Ambient air temperature sensor


Class A DTC stored

MONITOR DESCRIPTION

·

Engine start:

No. 5 exhaust gas temperature sensor rationality is checked by comparison with ambient temperature.

·

Engine running:

No. 5 exhaust gas temperature sensor rationality is checked by temperature model calculated from No. 4 exhaust gas temperature sensor.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2483 Drive for a certain amount of time after starting the engine.

WIRING DIAGRAM

A444323E01
0.229,2.01 3.281,2.198 3.052,0.188 10 false Ambient Temperature Sensor (Cooler Thermistor) 0.365,4.25 3.083,4.552 2.719,0.302 10 false No. 5 Exhaust Gas Temperature Sensor 4.635,0.885 4.948,1.031 0.313,0.146 10 false E-55 4.625,1.458 4.938,1.604 0.313,0.146 10 false E-60 5.042,0.865 5.354,1.01 0.313,0.146 10 false P12 5.052,1.448 5.365,1.594 0.313,0.146 10 false P12 5.042,2.958 5.354,3.104 0.313,0.146 10 false P12 5.073,0.667 5.385,0.813 0.313,0.146 10 false 55 5.073,1.26 5.385,1.406 0.313,0.146 10 false 60 5.427,0.865 5.854,1.021 0.427,0.156 10 false AMBT 5.417,1.469 5.844,1.625 0.427,0.156 10 false SGN4 5.271,4.094 6.719,4.479 1.448,0.385 10 false DCU (Emission Control ECU Assembly) 1.76,0.792 2.188,0.948 0.427,0.156 10 false HH1+ 1.771,1.333 2.198,1.49 0.427,0.156 10 false HH1- 5.417,2.99 5.844,3.146 0.427,0.156 10 false EGT1 4.646,2.979 4.958,3.125 0.313,0.146 10 false E-57 5.083,2.771 5.396,2.917 0.313,0.146 10 false 57 1.781,2.865 2.208,3.021 0.427,0.156 10 false TUW 1.698,3.385 2.125,3.542 0.427,0.156 10 false ETUW 0.24,1.844 0.667,2 0.427,0.156 10 false a8 0.375,4.063 0.802,4.219 0.427,0.156 10 false A113 2.208,0.771 2.635,0.927 0.427,0.156 10 false 1 2.219,2.875 2.646,3.031 0.427,0.156 10 false 1 2.219,1.323 2.646,1.479 0.427,0.156 10 false 2 2.219,3.438 2.646,3.594 0.427,0.156 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK EXHAUST PIPE
a.

Check for exhaust pipe crack, exhaust gas leak (soot contamination) and improper coupling flange tightening.


Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTOR CONNECTION CONDITION (NO. 5 EXHAUST GAS TEMPERATURE SENSORCONNECTOR)

NG

41.REPAIR OR REPLACE EXHAUST PIPE
2.CHECK CONNECTOR CONNECTION CONDITION (NO. 5 EXHAUST GAS TEMPERATURE SENSORCONNECTOR)
a.

Check the connector connection for the No. 5 exhaust gas temperature sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

3.CHECK NO. 5 EXHAUST GAS TEMPERATURE SENSOR

NG

40.CONNECT SECURELY
3.CHECK NO. 5 EXHAUST GAS TEMPERATURE SENSOR
a.

Check the installation of the No. 5 exhaust gas temperature sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the No. 5 exhaust gas temperature sensor.


Result:
Proceed to
OK
NG



OK

4.INSPECT NO. 5 EXHAUST GAS TEMPERATURE SENSOR

NG

39.REPAIR OR REPLACE NO. 5 EXHAUST GAS TEMPERATURE SENSOR
4.INSPECT NO. 5 EXHAUST GAS TEMPERATURE SENSOR
a.

Inspect the No. 5 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
OK
NG



OK

5.CHECK NO. 5 EXHAUST GAS TEMPERATURE SENSOR

NG

38.REPLACE NO. 5 EXHAUST GAS TEMPERATURE SENSOR
5.CHECK NO. 5 EXHAUST GAS TEMPERATURE SENSOR
A450001C05
0.604,0.948 1.021,1.25 0.417,0.302 1.198,1.75 1.563,1.24 true 2.167,1.74 1.875,1.25 true 0.104,0.125 0.417,0.323 0.313,0.198 10 false *a 0.656,1.031 1.167,1.208 0.51,0.177 10 false A113 0.969,1.771 1.479,1.948 0.51,0.177 10 false TUW 2.125,1.771 2.635,1.948 0.51,0.177 10 false ETUW
*a Front view of wire harness connector
(to No. 5 Exhaust Gas Temperature Sensor)


a.

Disconnect the No. 5 exhaust gas temperature sensor.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A113-1 (TUW) - A113-2 (ETUW) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

6.CHECK CONNECTOR CONNECTION CONDITION (AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR))

NG

32.CHECK HARNESS OR CONNECTOR (NO. 5 EXHAUST GAS TEMPERATURE SENSOR - ECM)
6.CHECK CONNECTOR CONNECTION CONDITION (AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR))
a.

Check the connector connection and contact pressure of the ambient temperature sensor (cooler thermistor) connector.

OK:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

7.INSPECT AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)

NG

31.CONNECT SECURELY
7.INSPECT AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)
a.

Check the installation of the ambient temperature sensor (cooler thermistor).


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the ambient temperature sensor (cooler thermistor).


Result:
Proceed to
OK
NG



OK

8.INSPECT AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)

NG

30.REPAIR OR REPLACE AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)
8.INSPECT AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)
a.

Inspect the ambient temperature sensor (cooler thermistor).

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL


Result:
Proceed to
OK
NG



OK

9.CHECK CONNECTOR CONNECTION CONDITION (DCU (EMISSION CONTROL ECU ASSEMBLY))

NG

29.REPLACE AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)
9.CHECK CONNECTOR CONNECTION CONDITION (DCU (EMISSION CONTROL ECU ASSEMBLY))
a.

Check the connector connection and contact pressure of the DCU (emission control ECU assembly) connector.

OK:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR) - DCU (EMISSION CONTROL ECU ASSEMBLY))

NG

28.CONNECT SECURELY
10.CHECK HARNESS AND CONNECTOR (AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR) - DCU (EMISSION CONTROL ECU ASSEMBLY))
a.
A405887C01
1.521,0.125 1.885,0.396 0.365,0.271 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 1.677,0.198 1.833,0.396 0.156,0.198 10 false E
*a Signal Check Harness Lead Connector
(for DCU (Emission Control ECU Assembly))


Connect the signal check harness to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-55 - Body ground Ignition switch off 10 kΩ or higher
E-60 - Body ground Ignition switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR) - DCU (EMISSION CONTROL ECU ASSEMBLY))

NG

27.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.CHECK HARNESS AND CONNECTOR (AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR) - DCU (EMISSION CONTROL ECU ASSEMBLY))
a.
A405887C01
1.521,0.125 1.885,0.396 0.365,0.271 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 1.677,0.198 1.833,0.396 0.156,0.198 10 false E
*a Signal Check Harness Lead Connector
(for DCU (Emission Control ECU Assembly))


Connect the ambient temperature sensor (cooler thermistor) connector.


b.

Connect the signal check harness to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-55 - E-60 20°C (68°F) 1.9 to 2.3 kΩ
40°C (104°F) 0.8 to 1.0 kΩ



Result:
Proceed to
OK
NG



OK

12.CHECK CONNECTOR CONNECTION CONDITION (NO. 4 EXHAUST GAS TEMPERATURE SENSOR CONNECTOR)

NG

26.REPAIR OR REPLACE HARNESS OR CONNECTOR
12.CHECK CONNECTOR CONNECTION CONDITION (NO. 4 EXHAUST GAS TEMPERATURE SENSOR CONNECTOR)
a.

Check the connector connection for the No. 4 exhaust gas temperature sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

13.CHECK NO. 4 EXHAUST GAS TEMPERATURE SENSOR

NG

25.CONNECT SECURELY
13.CHECK NO. 4 EXHAUST GAS TEMPERATURE SENSOR
a.

Check the installation of the No. 4 exhaust gas temperature sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the No. 4 exhaust gas temperature sensor.


Result:
Proceed to
OK
NG



OK

14.INSPECT NO. 4 EXHAUST GAS TEMPERATURE SENSOR

NG

24.REPAIR OR REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR
14.INSPECT NO. 4 EXHAUST GAS TEMPERATURE SENSOR
a.

Inspect the No. 4 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

15.CHECK CONNECTOR CONNECTION CONDITION (ENGINE COOLANT TEMPERATURE SENSOR CONNECTOR)

NG

23.REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR
15.CHECK CONNECTOR CONNECTION CONDITION (ENGINE COOLANT TEMPERATURE SENSOR CONNECTOR)
a.

Check the connector connection for the engine coolant temperature sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

16.CHECK ENGINE COOLANT TEMPERATURE SENSOR

NG

22.CONNECT SECURELY
16.CHECK ENGINE COOLANT TEMPERATURE SENSOR
a.

Check the installation of the engine coolant temperature sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the engine coolant temperature sensor.


Result:
Proceed to
OK
NG



OK

17.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

NG

21.REPAIR OR REPLACE ENGINE COOLANT TEMPERATURE SENSOR
17.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Result:
Proceed to
OK
NG



OK

18.INSPECT MASS AIR FLOW METER

NG

20.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
18.INSPECT MASS AIR FLOW METER
a.

Check the installation of the mass air flow meter.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the mass air flow meter.


Result:
Proceed to
OK
NG



OK

34.CHECK DTC OUTPUT

NG

19.REPAIR OR REPLACE MASS AIR FLOW METER
19.REPAIR OR REPLACE MASS AIR FLOW METER
a.

Repair or replace the mass air flow meter.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the mass air flow meter.



Result:
Proceed to
NEXT



NEXT

42.CHECK DTC OUTPUT
20.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

42.CHECK DTC OUTPUT
21.REPAIR OR REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

Repair or replace the engine coolant temperature sensor.


Result:
Proceed to
NEXT



NEXT

42.CHECK DTC OUTPUT
22.CONNECT SECURELY
a.

Connect securely the engine coolant temperature sensor connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

42.CHECK DTC OUTPUT
23.REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR
a.

Replace the No. 4 exhaust gas temperature sensor.


Result:
Proceed to
NEXT



NEXT

42.CHECK DTC OUTPUT
24.REPAIR OR REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR
a.

Repair or replace the No. 4 exhaust gas temperature sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the No. 4 exhaust gas temperature sensor.



Result:
Proceed to
NEXT



NEXT

42.CHECK DTC OUTPUT
25.CONNECT SECURELY
a.

Connect securely the No. 4 exhaust gas temperature sensor connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

42.CHECK DTC OUTPUT
26.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

42.CHECK DTC OUTPUT
27.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

42.CHECK DTC OUTPUT
28.CONNECT SECURELY
a.

Securely connect the DCU (emission control ECU assembly) connector.

HINT:

Repair parts as necessary.



Result:
Proceed to
NEXT



NEXT

42.CHECK DTC OUTPUT
29.REPLACE AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)
a.

Replace the ambient temperature sensor (cooler thermistor).

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

42.CHECK DTC OUTPUT
30.REPAIR OR REPLACE AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)
a.

Clean the sensing part of the ambient temperature sensor (cooler thermistor) and correctly install it.

HINT:

If the ambient temperature sensor (cooler thermistor) is damaged, replace it.



Result:
Proceed to
NEXT



NEXT

42.CHECK DTC OUTPUT
31.CONNECT SECURELY
a.

Securely connect the ambient temperature sensor (cooler thermistor) connector.

HINT:

Repair parts as necessary.



Result:
Proceed to
NEXT



NEXT

42.CHECK DTC OUTPUT
32.CHECK HARNESS OR CONNECTOR (NO. 5 EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the No. 5 exhaust gas temperature sensor connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-57 - Body ground and other terminals Always 10 kΩ or higher
E-60 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

33.CHECK HARNESS OR CONNECTOR (NO. 5 EXHAUST GAS TEMPERATURE SENSOR - ECM)

NG

37.REPAIR OR REPLACE HARNESS OR CONNECTOR
33.CHECK HARNESS OR CONNECTOR (NO. 5 EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Turn the ignition switch off.


b.

Connect the No. 5 exhaust gas temperature sensor connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-57 - E-66 Always (20°C) 13.7 to 29.8 kΩ
E-57 - E-66 Always (50°C) 7.13 to 13.7 kΩ
E-57 - E-66 Always (80°C) 4.1 to 7.13 kΩ



Result:
Proceed to
OK
NG



OK

34.CHECK DTC OUTPUT

NG

36.REPAIR OR REPLACE HARNESS OR CONNECTOR
34.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P2483 is output A
DTCs are not output B




A

35.REPLACE ECM

B

END

35.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

42.CHECK DTC OUTPUT
36.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

42.CHECK DTC OUTPUT
37.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

42.CHECK DTC OUTPUT
38.REPLACE NO. 5 EXHAUST GAS TEMPERATURE SENSOR
a.

Replace the No. 5 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

42.CHECK DTC OUTPUT
39.REPAIR OR REPLACE NO. 5 EXHAUST GAS TEMPERATURE SENSOR
a.

Repair or replace the No. 5 exhaust gas temperature sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the No. 5 exhaust gas temperature sensor.



Result:
Proceed to
NEXT



NEXT

42.CHECK DTC OUTPUT
40.CONNECT SECURELY
a.

Connect securely the No. 5 exhaust gas temperature sensor connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

42.CHECK DTC OUTPUT
41.REPAIR OR REPLACE EXHAUST PIPE
a.

Repair the exhaust pipe.

HINT:

Replace it as needed.



Result:
Proceed to
NEXT



NEXT

42.CHECK DTC OUTPUT
42.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END