Home › Engine / Hybrid System › N04C-WA (EMISSION CONTROL) › UREA SELECTIVE CATALYTIC REDUCTION SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082614 N04C-WA EMISSION CONTROL _0400651 UREA SELECTIVE CATALYTIC REDUCTION SYSTEM C

N04C-WA EMISSION CONTROL  UREA SELECTIVE CATALYTIC REDUCTION SYSTEM  P007162  Ambient Air Temperature Sensor Circuit "A" Range/Performance Signal Compare Failure  


DESCRIPTION

Ambient temperature sensor (cooler thermistor) rationality is checked by comparison with intake air temperature (mass air flow meter sub-assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
P007162 Ambient Air Temperature Sensor Circuit "A" Range/Performance Signal Compare Failure Diagnosis Condition:
·

Ignition switch ON.

·

The difference between the SCR inlet exhaust gas temperature and the engine coolant temperature is less than 8°C (14.4°F).

·

The current engine coolant temperature is lower than the engine coolant temperature the last time the ignition switch was turned off by 20°C (36°F) or more.


Malfunction Status:
·

The difference between the ambient temperature (cooler thermistor) and the intake air temperature (mass air flow meter sub-assembly) is 50°C (90°F) or higher.


Malfunction Duration:
·

69 seconds or more


·

Open or short in ambient temperature sensor circuit

·

Ambient temperature sensor (cooler thermistor)

·

Intake air temperature sensor (mass air flow meter sub-assembly)

·

DCU (emission control ECU assembly)


Class C AdBlue consumption warning light:
Comes on
DTC stored

MONITOR DESCRIPTION

Description of malfunction

Ambient temperature sensor (cooler thermistor) malfunction detected.


Reset condition

After normal determination subsequent to meeting of conditions.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P007162 After warming up the engine, turn the ignition switch off. After the engine sufficiently cools, start the engine and idle the engine for 69 seconds or more.

WIRING DIAGRAM

A444323E01
0.229,2.01 3.281,2.198 3.052,0.188 10 false Ambient Temperature Sensor (Cooler Thermistor) 0.365,4.25 3.083,4.552 2.719,0.302 10 false No. 5 Exhaust Gas Temperature Sensor 4.635,0.885 4.948,1.031 0.313,0.146 10 false E-55 4.625,1.458 4.938,1.604 0.313,0.146 10 false E-60 5.042,0.865 5.354,1.01 0.313,0.146 10 false P12 5.052,1.448 5.365,1.594 0.313,0.146 10 false P12 5.042,2.958 5.354,3.104 0.313,0.146 10 false P12 5.073,0.667 5.385,0.813 0.313,0.146 10 false 55 5.073,1.26 5.385,1.406 0.313,0.146 10 false 60 5.427,0.865 5.854,1.021 0.427,0.156 10 false AMBT 5.417,1.469 5.844,1.625 0.427,0.156 10 false SGN4 5.271,4.094 6.719,4.479 1.448,0.385 10 false DCU (Emission Control ECU Assembly) 1.76,0.792 2.188,0.948 0.427,0.156 10 false HH1+ 1.771,1.333 2.198,1.49 0.427,0.156 10 false HH1- 5.417,2.99 5.844,3.146 0.427,0.156 10 false EGT1 4.646,2.979 4.958,3.125 0.313,0.146 10 false E-57 5.083,2.771 5.396,2.917 0.313,0.146 10 false 57 1.781,2.865 2.208,3.021 0.427,0.156 10 false TUW 1.698,3.385 2.125,3.542 0.427,0.156 10 false ETUW 0.24,1.844 0.667,2 0.427,0.156 10 false a8 0.375,4.063 0.802,4.219 0.427,0.156 10 false A113 2.208,0.771 2.635,0.927 0.427,0.156 10 false 1 2.219,2.875 2.646,3.031 0.427,0.156 10 false 1 2.219,1.323 2.646,1.479 0.427,0.156 10 false 2 2.219,3.438 2.646,3.594 0.427,0.156 10 false 2

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (AMBIENT TEMPERATURE AND INTAKE AIR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Data List / Ambient Temperature.


e.

Read the value.


f.

Enter the following menus: Powertrain / Engine / Data List / Intake Air.


g.

Read the value.

OK:

The difference between the Ambient Temperature and the Intake Air is 8°C (14.4°F) or less.



Result:
Proceed to
OK
NG



OK

2.CHECK INTAKE AIR TEMPERATURE SENSOR (MASS AIR FLOW METER SUB-ASSEMBLY)

NG

3.CHECK CONNECTOR CONNECTION CONDITION (AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR))
2.CHECK INTAKE AIR TEMPERATURE SENSOR (MASS AIR FLOW METER SUB-ASSEMBLY)
a.

Check the intake air temperature sensor (mass air flow meter sub-assembly) and if there are any malfunctions, repair or replace it.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION


Result:
Proceed to
NEXT



NEXT

14.CLEAR DTC
3.CHECK CONNECTOR CONNECTION CONDITION (AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR))
a.

Check the connector connection and contact pressure of the ambient temperature sensor (cooler thermistor) connector.

OK:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

4.CHECK CONNECTOR CONNECTION CONDITION (DCU (EMISSION CONTROL ECU ASSEMBLY))

NG

13.CONNECT SECURELY
4.CHECK CONNECTOR CONNECTION CONDITION (DCU (EMISSION CONTROL ECU ASSEMBLY))
a.

Check the connector connection and contact pressure of the DCU (emission control ECU assembly) connector.

OK:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

5.INSPECT AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)

NG

12.CONNECT SECURELY
5.INSPECT AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)
a.

Check the installation condition (rattling and looseness) of the ambient temperature sensor (cooler thermistor).


b.

Check that the sensing part of the ambient temperature sensor (cooler thermistor) is free of dirt, blockage and damage.


OK:

The sensing part of the ambient temperature sensor (cooler thermistor) is normal and the ambient temperature sensor (cooler thermistor) is correctly installed.


Result:
Proceed to
OK
NG



OK

6.INSPECT AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)

NG

11.REPAIR OR REPLACE AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)
6.INSPECT AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)
a.

Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR) - DCU (EMISSION CONTROL ECU ASSEMBLY))

NG

10.REPLACE AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)
7.CHECK HARNESS AND CONNECTOR (AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR) - DCU (EMISSION CONTROL ECU ASSEMBLY))
a.
A405887C01
1.521,0.125 1.885,0.396 0.365,0.271 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 1.677,0.198 1.833,0.396 0.156,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


Connect the ambient temperature sensor (cooler thermistor) connector.


b.

Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-55 (AMBT) - E-60 (SGN4) 20°C 1.9 to 2.3 kΩ
40°C 0.8 to 1.0 kΩ



Result:
Proceed to
OK
NG



OK

8.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)
a.

Replace the DCU (emission control ECU assembly).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CLEAR DTC
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

14.CLEAR DTC
10.REPLACE AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)
a.

Replace the ambient temperature sensor (cooler thermistor).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>AMBIENT TEMPERATURE SENSOR (for Urea SCR System)>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CLEAR DTC
11.REPAIR OR REPLACE AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)
a.

Clean the sensing part of the ambient temperature sensor and correctly install it.

HINT:

If the ambient temperature sensor (cooler thermistor) is damaged, replace it.



Result:
Proceed to
NEXT



NEXT

14.CLEAR DTC
12.CONNECT SECURELY
a.

Securely connect the DCU (emission control ECU assembly) connector.

HINT:

Repair parts as necessary.



Result:
Proceed to
NEXT



NEXT

14.CLEAR DTC
13.CONNECT SECURELY
a.

Securely connect the ambient temperature sensor (cooler thermistor) connector.

HINT:

Repair parts as necessary.



Result:
Proceed to
NEXT



NEXT

14.CLEAR DTC
14.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

15.CHECK WHETHER DTC OUTPUT RECURS (DTC P007162)
15.CHECK WHETHER DTC OUTPUT RECURS (DTC P007162)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

OK:

DTCs are not output



Result:
Proceed to
NEXT



NEXT

END