Home › Engine / Hybrid System › N04C-WA (EMISSION CONTROL) › UREA SELECTIVE CATALYTIC REDUCTION SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082614 N04C-WA EMISSION CONTROL _0400651 UREA SELECTIVE CATALYTIC REDUCTION SYSTEM C

N04C-WA EMISSION CONTROL  UREA SELECTIVE CATALYTIC REDUCTION SYSTEM  P007315  Ambient Air Temperature Sensor Circuit "A" High Circuit Short to Battery or Open  


DESCRIPTION

The ambient air temperature sensor inputs the outside air temperature data into the DCU (emission control ECU assembly) to determine the heating time when performing thermal insulation of the urea solution in the SCR system.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
P007315 Ambient Air Temperature Sensor Circuit "A" High Circuit Short to Battery or Open Diagnosis Condition:
·

Ignition switch ON.


Malfunction Status:
·

The ambient temperature sensor voltage is higher than 4.87 V.


Malfunction Duration:
·

5 seconds or more.


·

Open or short in ambient temperature sensor circuit

·

Ambient temperature sensor

·

DCU (emission control ECU assembly)


Class C AdBlue consumption warning light:
Comes on
DTC stored

MONITOR DESCRIPTION

Description of malfunction

Ambient temperature sensor malfunction detected.


Reset condition

After having restored to the normal conditions.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P007315 Ignition switch ON for 5 seconds or more.

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (AMBIENT TEMPERATURE SENSOR)
a.

Check the connector connection and contact pressure of the ambient temperature sensor (cooler thermistor) connector.

OK:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.INSPECT AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)

NG

14.CONNECT SECURELY
2.INSPECT AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)
a.

Check the installation condition (rattling and looseness) of the ambient temperature sensor (cooler thermistor).


b.

Check that the sensing part of the ambient temperature sensor (cooler thermistor) is free of dirt, blockage and damage.


OK:

The sensing part of the ambient temperature sensor (cooler thermistor) is normal and the ambient temperature sensor (cooler thermistor) is correctly installed.


Result:
Proceed to
OK
NG



OK

3.INSPECT AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)

NG

13.REPAIR OR REPLACE AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)
3.INSPECT AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)
a.

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR) POWER SOURCE VOLTAGE)

NG

12.REPLACE AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)
4.CHECK HARNESS AND CONNECTOR (AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR) POWER SOURCE VOLTAGE)
a.
A444331C01
0.396,1.042 0.771,1.281 0.375,0.24 1.073,1.792 1.563,1.375 true 2.5,1.792 1.948,1.365 true 0.156,0.135 0.479,0.427 0.323,0.292 10 false *a 0.51,1.094 0.802,1.26 0.292,0.167 10 false a8 0.875,1.833 1.26,2.01 0.385,0.177 10 false HH1+ 2.438,1.844 2.823,2.021 0.385,0.177 10 false HH1-
*a Front view of wire harness connector
(to Ambient Temperature Sensor (Cooler Thermistor))


Disconnect the ambient temperature sensor (cooler thermistor) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
a8-1 (HH1+) - a8-2 (HH1-) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

7.CLEAR DTC

NG

5.CHECK HARNESS AND CONNECTOR (AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR) - DCU (EMISSION CONTROL ECU ASSEMBLY))
5.CHECK HARNESS AND CONNECTOR (AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR) - DCU (EMISSION CONTROL ECU ASSEMBLY))
a.
A405887C01
1.521,0.125 1.885,0.396 0.365,0.271 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 1.677,0.198 1.833,0.396 0.156,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-55 (AMBT) - Body ground Ignition switch off 10 kΩ or higher
E-60 (SGN4) - Body ground Ignition switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR) - DCU (EMISSION CONTROL ECU ASSEMBLY))

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK HARNESS AND CONNECTOR (AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR) - DCU (EMISSION CONTROL ECU ASSEMBLY))
a.
A405887C01
1.521,0.125 1.885,0.396 0.365,0.271 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 1.677,0.198 1.833,0.396 0.156,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


Connect the ambient temperature sensor (cooler thermistor) connector.


b.

Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-55 (AMBT) - E-60 (SGN4) 0°C 5.30 to 6.05 kΩ
10°C 4.18 to 4.56 kΩ
25°C 3.13 to 3.26 kΩ



Result:
Proceed to
OK
NG



OK

7.CLEAR DTC

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P007315)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P007315)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

Result:
Result Proceed to
DTC P007315 is output A
DTCs are not output B




A

9.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)

B

END

9.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)
a.

Replace the DCU (emission control ECU assembly).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.CLEAR DTC
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

15.CLEAR DTC
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

15.CLEAR DTC
12.REPLACE AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)
a.

Replace the ambient temperature sensor (cooler thermistor).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>AMBIENT TEMPERATURE SENSOR (for Urea SCR System)>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.CLEAR DTC
13.REPAIR OR REPLACE AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)
a.

Clean the sensing part of the ambient temperature sensor (cooler thermistor) and correctly install it.

HINT:

If the ambient temperature sensor (cooler thermistor) is damaged, replace it.



Result:
Proceed to
NEXT



NEXT

15.CLEAR DTC
14.CONNECT SECURELY
a.

Securely connect the ambient temperature sensor (cooler thermistor) connector.

HINT:

Repair parts as necessary.



Result:
Proceed to
NEXT



NEXT

15.CLEAR DTC
15.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

16.CHECK WHETHER DTC OUTPUT RECURS (DTC P007315)
16.CHECK WHETHER DTC OUTPUT RECURS (DTC P007315)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

OK:

DTCs are not output



Result:
Proceed to
NEXT



NEXT

END