Power is supplied to the pressure sensor (urea pump) power supply circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate | Memory |
|---|---|---|---|---|---|---|
| P0643A3 | Sensor Reference Voltage "A" Circuit High System Voltage High | Diagnosis Condition:
·
Ignition switch ON. ·
Battery voltage is 9 V to 16 V. Malfunction Status: ·
The pressure sensor (urea pump) power supply circuit voltage is higher than 5.62 V. Malfunction Duration: ·
At least 5 seconds. |
·
Open or short in pressure sensor (urea pump) circuit ·
Pressure sensor (urea pump) ·
DCU (emission control ECU assembly) |
Class A | AdBlue consumption warning light:
Comes on |
DTC stored |
High voltage failure of pressure sensor (urea pump) power supply circuit is detected.
Immediately after normal operation is restored.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0643A3 | Ignition switch ON for 5 seconds or more. |
For the circuit diagram of the pressure sensor (urea pump) refer to DTC P0642A2.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P0642A2
For the circuit diagram of the DCU (emission control ECU assembly) power source refer to the DTC P0562A2.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P0562A2
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the urea pump connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0643A3 is output | A |
| DTC P0643A3 is not output | B |
A
B
| *a | Signal Check Harness No. 2 Lead Connector |
| *a | Signal Check Harness No. 2 Lead Connector |
Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E-17 (+BU1) - E-49 (GND8) | Ignition switch off | 10 kΩ or higher |
| E-18 (+BU2) - E-49 (GND8) | Ignition switch off | 10 kΩ or higher |
| E-19 (+BU3) - E-49 (GND8) | Ignition switch off | 10 kΩ or higher |
| E-30 (BATT) - E-49 (GND8) | Ignition switch off | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Signal Check Harness No. 2 Lead Connector |
Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E-25 (VCPU) - E-17 (+BU1) | Ignition switch off | 10 kΩ or higher |
| E-25 (VCPU) - E-18(+BU2) | Ignition switch off | 10 kΩ or higher |
| E-25 (VCPU) - E-19(+BU3) | Ignition switch off | 10 kΩ or higher |
| E-25 (VCPU) - E-30 (BATT) | Ignition switch off | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the DCU (emission control ECU assembly).
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the urea pump.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.
Read the DTCs.
DTCs are not output
| Proceed to |
|---|
| NEXT |
NEXT