Home › Engine / Hybrid System › N04C-WA (EMISSION CONTROL) › UREA SELECTIVE CATALYTIC REDUCTION SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082614 N04C-WA EMISSION CONTROL _0400651 UREA SELECTIVE CATALYTIC REDUCTION SYSTEM C

N04C-WA EMISSION CONTROL  UREA SELECTIVE CATALYTIC REDUCTION SYSTEM  P203B64  Reductant Level Sensor "A" Circuit Range/Performance Signal Plausibility Failure  


DESCRIPTION

The level sensor (integrated in urea pump) measures the quantity of urea solution remaining in the urea tank.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
P203B64 Reductant Level Sensor "A" Circuit Range/Performance Signal Plausibility Failure Diagnosis Condition:
·

Urea solution is not frozen.

·

Urea solution is charged to the specified level or more.

·

Vehicle is running.


Malfunction Status:
·

Abnormality in the output of level sensor (integrated in urea pump) or detection is made that the level does not change.


Malfunction Duration:
·

-


·

Open or short in level sensor (urea pump) circuit

·

Level sensor (urea pump)

·

DCU (emission control ECU assembly)


Class C AdBlue consumption warning light:
Comes on
DTC stored

MONITOR DESCRIPTION

Description of malfunction

Malfunction of level sensor (urea pump) is detected.


Reset condition

Immediately after the normal operation is resumed.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P203B64 Vehicle being driven.

CAUTION / NOTICE / HINT

NOTICE:
Handling urea solution
·

Wear protective equipment as necessary (protective glasses and gloves).

·

Do not dilute urea solution.

·

If urea solution contacts your eyes or skin, immediately wash the contacted area with a large amount of water and consult a doctor as necessary.

·

If urea solution dries, it deposits a white powder. Also, if urea solution contacts metals such as copper and aluminum for a long period of time, it may promote corrosion. Therefore, if urea solution is spilled, dampen a cloth or other item and wipe it up or rinse the area with cool or warm water.


Handling the urea injector assembly
·

The urea injector assembly is a precision instrument. Take necessary precautions for installation and shipping. Do not use the part if it has been struck or dropped.

·

If the urea solution remaining inside the urea injector assembly dries out, it may become unable to inject urea solution. Therefore, conduct urea tube with heater assembly installation and removal quickly.

·

If the urea solution dries out and deposition occurs, urea may cling to the O-ring of the pipe and cause seal problems. Therefore, clean the urea tube with heater assembly and intake port of the urea injector assembly with water before attaching them.

·

Perform this procedure in an environment where urea solution will not freeze.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (REDUCTANT TANK LEVEL SENSOR VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Data List / Reductant Tank Level Sensor Voltage.


d.

Read the value.

OK:

4.8 V or less.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (REDUCTANT TANK LEVEL SENSOR VOLTAGE)

NG

16.INSPECT LEVEL SENSOR (UREA PUMP)
2.READ VALUE USING GTS (REDUCTANT TANK LEVEL SENSOR VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Data List / Reductant Tank Level Sensor Voltage.


d.

Read the Data List and check that it matches the urea solution gauge of the combination meter.

Standard Value:
Condition Urea solution gauge Reductant Tank Level Sensor Voltage
IG ON 3/4 to F 3.81 to 4.76 V
2/4 to 3/4 2.86 to 3.80 V
1/4 to 2/4 1.91 to 2.85 V
E to 1/4 0.96 to 1.90 V



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (REDUCTANT TANK LEVEL SENSOR VOLTAGE)

NG

3.CHECK HARNESS AND CONNECTOR (LEVEL SENSOR (UREA PUMP) - DCU (EMISSION CONTROL ECU ASSEMBLY))
3.CHECK HARNESS AND CONNECTOR (LEVEL SENSOR (UREA PUMP) - DCU (EMISSION CONTROL ECU ASSEMBLY))
a.
A405886C01
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


A360358C13
1.479,0.833 1.896,1.094 0.417,0.26 1.615,1.813 1.156,2.531 true 0.146,0.177 0.458,0.375 0.313,0.198 10 false *a 1.583,0.896 1.896,1.094 0.313,0.198 10 false P11 1,2.563 1.74,2.76 0.74,0.198 10 false VCLU
*a Front view of wire harness connector
(to Urea Pump)


Disconnect the level sensor (urea pump) connector.


b.

Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-24 (VCLU) - P11-13 (VCLU) Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (REDUCTANT TANK LEVEL SENSOR VOLTAGE)

NG

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.READ VALUE USING GTS (REDUCTANT TANK LEVEL SENSOR VOLTAGE)
a.
A444327C01
0.365,1.156 0.563,1.156 0.563,1.156 1.49,1.656 false 2.802,0.583 2.594,0.583 2.594,0.583 1.635,1.115 false 0.188,1.073 0.5,1.229 0.313,0.156 10 false *1 2.854,0.51 3.167,0.667 0.313,0.156 10 false *2
*1 Float
*2 Level Sensor


Remove the urea pump from the urea tank.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP>REMOVAL


b.

Connect the urea pump connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Data List / Reductant Tank Level Sensor Voltage.


g.

Move the float of the level sensor from the upper end to the lower end and read the Data List.

OK:

Voltage value changes.



Result:
Proceed to
OK
NG



OK

5.CHECK CONNECTOR CONNECTION CONDITION (LEVEL SENSOR (UREA PUMP))

NG

14.REPAIR OR REPLACE LEVEL SENSOR (UREA PUMP)
5.CHECK CONNECTOR CONNECTION CONDITION (LEVEL SENSOR (UREA PUMP))
a.

Check the connector connection and contact pressure of the level sensor (urea pump) connector.

OK:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

6.CHECK CONNECTOR CONNECTION CONDITION (DCU (EMISSION CONTROL ECU ASSEMBLY))

NG

13.CONNECT SECURELY
6.CHECK CONNECTOR CONNECTION CONDITION (DCU (EMISSION CONTROL ECU ASSEMBLY))
a.

Check the connector connection and contact pressure of the DCU (emission control ECU assembly) connector.

OK:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

7.INSPECT LEVEL SENSOR (UREA PUMP)

NG

12.CONNECT SECURELY
7.INSPECT LEVEL SENSOR (UREA PUMP)
a.
A355506C07
1.479,1.74 1.979,1.177 false 2.51,1.708 2.083,1 false 0.135,0.135 0.448,0.333 0.313,0.198 10 false *a 1.333,1.771 1.708,1.938 0.375,0.167 10 false LVU 2.448,1.74 2.823,1.906 0.375,0.167 10 false ELU
*a Component without harness connected
(Level Sensor (Urea Pump))


Disconnect the level sensor (urea pump) connector.


b.

Remove the urea pump from the urea tank.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
14 (LVU) - 6 (ELU) Uppermost position 85.90 to 89.94 kΩ
Lowermost position 1.40 to 1.46 kΩ



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (LEVEL SENSOR (UREA PUMP) - DCU (EMISSION CONTROL ECU ASSEMBLY))

NG

11.REPLACE LEVEL SENSOR (UREA PUMP)
8.CHECK HARNESS AND CONNECTOR (LEVEL SENSOR (UREA PUMP) - DCU (EMISSION CONTROL ECU ASSEMBLY))
a.
A405886C01
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


A405887C01
1.521,0.125 1.885,0.396 0.365,0.271 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 1.677,0.198 1.833,0.396 0.156,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


Connect the level sensor (urea pump) connector.


b.

Disconnect the DCU (emission control ECU assembly) connector.


c.

Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-58 (LVU) -E-36 (ELU) Uppermost position 85.90 to 89.94 kΩ
Lowermost position 1.40 to 1.46 kΩ



Result:
Proceed to
OK
NG



OK

9.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)
a.

Replace the DCU (emission control ECU assembly).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

19.CLEAR DTC
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

19.CLEAR DTC
11.REPLACE LEVEL SENSOR (UREA PUMP)
a.

Replace the level sensor (urea pump).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

19.CLEAR DTC
12.CONNECT SECURELY
a.

Securely connect the DCU (emission control ECU assembly) connector.

HINT:

Repair parts as necessary.



Result:
Proceed to
NEXT



NEXT

19.CLEAR DTC
13.CONNECT SECURELY
a.

Securely connect the level sensor (urea pump) connector.

HINT:

Repair parts as necessary.



Result:
Proceed to
NEXT



NEXT

19.CLEAR DTC
14.REPAIR OR REPLACE LEVEL SENSOR (UREA PUMP)
a.

Repair or replace the level sensor (urea pump).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

19.CLEAR DTC
15.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

19.CLEAR DTC
16.INSPECT LEVEL SENSOR (UREA PUMP)
a.
A444327C01
0.365,1.156 0.563,1.156 0.563,1.156 1.49,1.656 false 2.802,0.583 2.594,0.583 2.594,0.583 1.635,1.115 false 0.188,1.073 0.5,1.229 0.313,0.156 10 false *1 2.854,0.51 3.167,0.667 0.313,0.156 10 false *2
*1 Float
*2 Level Sensor


Remove the urea pump from the urea tank.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP>REMOVAL


b.

Move the float of the level sensor from the upper end to the lower end.

OK:

Level sensor float is normal and moves smoothly.



Result:
Proceed to
OK
NG



OK

17.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)

NG

18.REPLACE LEVEL SENSOR (UREA PUMP)
17.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)
a.

Replace the DCU (emission control ECU assembly).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

19.CLEAR DTC
18.REPLACE LEVEL SENSOR (UREA PUMP)
a.

Replace the level sensor (urea pump).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

19.CLEAR DTC
19.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

20.CHECK WHETHER DTC OUTPUT RECURS (DTC P203B64)
20.CHECK WHETHER DTC OUTPUT RECURS (DTC P203B64)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

OK:

DTCs are not output



Result:
Proceed to
NEXT



NEXT

END