Home › Engine / Hybrid System › N04C-WA (EMISSION CONTROL) › UREA SELECTIVE CATALYTIC REDUCTION SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082614 N04C-WA EMISSION CONTROL _0400651 UREA SELECTIVE CATALYTIC REDUCTION SYSTEM C

N04C-WA EMISSION CONTROL  UREA SELECTIVE CATALYTIC REDUCTION SYSTEM  P0652A2  Sensor Reference Voltage "B" Circuit Low System Voltage Low  


DESCRIPTION

Power is supplied to the level sensor (urea pump) power supply circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
P0652A2 Sensor Reference Voltage "B" Circuit Low System Voltage Low Diagnosis Condition:
·

Ignition switch ON.

·

Battery voltage is 9 V to 16 V.


Malfunction Status:
·

The level sensor (urea pump) power supply circuit voltage is 4.375 V or less.


Malfunction Duration:
·

At least 5 seconds.


·

Open or short in level sensor (urea pump) circuit

·

Level sensor (urea pump)

·

DCU (emission control ECU assembly)


Class B1 AdBlue consumption warning light:
Comes on
DTC stored

MONITOR DESCRIPTION

Description of malfunction

Low voltage failure of level sensor (urea pump) power supply circuit is detected.


Reset condition

Immediately after normal operation is restored.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0652A2 Ignition switch ON for 5 seconds or more.

WIRING DIAGRAM

·

Level sensor (urea pump) circuit.

A407156E04
1.177,2.51 2.948,2.729 1.771,0.219 10 false Level Sensor (Urea Pump) 1.188,2.323 1.646,2.521 0.458,0.198 10 false P11 2.448,1 2.906,1.198 0.458,0.198 10 false 13 2.448,1.396 2.906,1.594 0.458,0.198 10 false 14 2.5,1.75 2.958,1.948 0.458,0.198 10 false 6 5.375,1.5 5.833,1.698 0.458,0.198 10 false LVU 5,1.104 5.458,1.302 0.458,0.198 10 false P12 5.396,1.885 5.854,2.083 0.458,0.198 10 false ELU 5.26,2.719 6.729,3.188 1.469,0.469 10 false DCU (Emission Control ECU Assembly) 5,1.479 5.458,1.677 0.458,0.198 10 false P12 5,1.854 5.458,2.052 0.458,0.198 10 false P12 5.396,1.146 5.854,1.344 0.458,0.198 10 false VCLU 4.594,1.125 5.052,1.323 0.458,0.198 10 false E-24 4.604,1.875 5.063,2.073 0.458,0.198 10 false E-36 4.615,1.5 5.073,1.698 0.458,0.198 10 false E-58 5.042,0.917 5.5,1.115 0.458,0.198 10 false 24 5.042,1.292 5.5,1.49 0.458,0.198 10 false 58 5.042,1.667 5.5,1.865 0.458,0.198 10 false 36 1.99,1.125 2.448,1.323 0.458,0.198 10 false VCLU 2.083,1.479 2.542,1.677 0.458,0.198 10 false LVU 2.073,1.854 2.531,2.052 0.458,0.198 10 false ELU

·

For the circuit diagram of the DCU (emission control ECU assembly) power source refer to the DTC P0562A2.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P0562A2

·

For the circuit diagram of the SGN4 terminal refer to the DTC P007162.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P007162

·

For the circuit diagram of the EPU terminal refer to the DTC P0642A2.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P0642A2

·

For the circuit diagram of the ISG terminal refer to the DTC P202E71.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P202E71

·

For the circuit diagram of the ETHU terminal refer to the DTC P205B62.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P205B62

·

For the circuit diagram of the MSG terminal refer to the DTC P208C11.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P208C11


CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

2.CHECK DTC OUTPUT
2.CHECK DTC OUTPUT
a.

Disconnect the urea pump connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

Result:
Result Proceed to
DTC P0652A2 is output A
DTC P0652A2 is not output B




A

3.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE CIRCUIT)

B

8.REPLACE UREA PUMP
3.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE CIRCUIT)
a.
A405886C01
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


A405887C01
1.521,0.125 1.885,0.396 0.365,0.271 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 1.677,0.198 1.833,0.396 0.156,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-17 (+BU1) - E-49 (GND8) Ignition switch off 10 kΩ or higher
E-18 (+BU2) - E-49 (GND8) Ignition switch off 10 kΩ or higher
E-19 (+BU3) - E-49 (GND8) Ignition switch off 10 kΩ or higher
E-30 (BATT) - E-49 (GND8) Ignition switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PRESSURE SENSOR (UREA PUMP) - DCU (EMISSION CONTROL ECU ASSEMBLY))

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS AND CONNECTOR (PRESSURE SENSOR (UREA PUMP) - DCU (EMISSION CONTROL ECU ASSEMBLY))
a.
A405886C01
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


A405887C01
1.521,0.125 1.885,0.396 0.365,0.271 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 1.677,0.198 1.833,0.396 0.156,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-24 (VCLU) - Body ground Ignition switch off 10 kΩ or higher
E-24 (VCLU) - E-36 (ELU) Ignition switch off 10 kΩ or higher
E-24 (VCLU) - E-37 (ISG) Ignition switch off 10 kΩ or higher
E-24 (VCLU) - E-43 (ETHU) Ignition switch off 10 kΩ or higher
E-24 (VCLU) - E-44 (EPU) Ignition switch off 10 kΩ or higher
E-24 (VCLU) - E-45 (MSG) Ignition switch off 10 kΩ or higher
E-24 (VCLU) - E-60 (SGN4) Ignition switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)
a.

Replace the DCU (emission control ECU assembly).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CLEAR DTC
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CLEAR DTC
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CLEAR DTC
8.REPLACE UREA PUMP

Result:
Proceed to
NEXT



NEXT

9.CLEAR DTC
9.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0652A2)
10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0652A2)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

OK:

DTCs are not output



Result:
Proceed to
NEXT



NEXT

END