Home › Engine / Hybrid System › N04C-WA (EMISSION CONTROL) › UREA SELECTIVE CATALYTIC REDUCTION SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082614 N04C-WA EMISSION CONTROL _0400651 UREA SELECTIVE CATALYTIC REDUCTION SYSTEM C

N04C-WA EMISSION CONTROL  UREA SELECTIVE CATALYTIC REDUCTION SYSTEM  P203C11  Reductant Level Sensor "A" Circuit Low Circuit Short to Ground  P203D15  Reductant Level Sensor "A" Circuit High Circuit Short to Battery or Open  


DESCRIPTION

The level sensor (urea pump) is connected DCU (emission control ECU assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
P203C11 Reductant Level Sensor "A" Circuit Low Circuit Short to Ground Diagnosis Condition:
·

Ignition switch ON.


Malfunction Status:
·

The level sensor voltage is below 0.464 V.


Malfunction Duration:
·

3 seconds or more.


·

Open or short in level sensor (urea pump) circuit

·

Level sensor (urea pump)

·

DCU (emission control ECU assembly)


Class C AdBlue consumption warning light:
Comes on
DTC stored
P203D15 Reductant Level Sensor "A" Circuit High Circuit Short to Battery or Open Diagnosis Condition:
·

Ignition switch ON.


Malfunction Status:
·

The level sensor voltage is higher than 4.88 V.


Malfunction Duration:
·

3 seconds or more.


·

Open or short in level sensor (urea pump) circuit

·

Level sensor (urea pump)

·

DCU (emission control ECU assembly)


Class C AdBlue consumption warning light:
Comes on
DTC stored

MONITOR DESCRIPTION

Description of malfunction

High voltage or low voltage is detected with the level sensor (urea pump).


Reset condition

After having restored to the normal conditions.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P203C11 Ignition switch ON for 5 seconds or more.
P203D15

CAUTION / NOTICE / HINT

NOTICE:
Handling urea solution
·

Wear protective equipment as necessary (protective glasses and gloves).

·

Do not dilute urea solution.

·

If urea solution contacts your eyes or skin, immediately wash the contacted area with a large amount of water and consult a doctor as necessary.

·

If urea solution dries, it deposits a white powder. Also, if urea solution contacts metals such as copper and aluminum for a long period of time, it may promote corrosion. Therefore, if urea solution is spilled, dampen a cloth or other item and wipe it up or rinse the area with cool or warm water.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (LEVEL SENSOR (UREA PUMP))
a.

Check the connector connection and contact pressure of the level sensor (urea pump) connector.

OK:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.INSPECT LEVEL SENSOR (UREA PUMP)

NG

12.CONNECT SECURELY
2.INSPECT LEVEL SENSOR (UREA PUMP)
a.

Check that the sensing part of the level sensor (urea pump) is free of dirt, blockage and damage.


OK:

The sensing part of the level sensor (urea pump) is normal.


Result:
Proceed to
OK
NG



OK

3.INSPECT LEVEL SENSOR (UREA PUMP)

NG

11.REPAIR OR REPLACE LEVEL SENSOR (UREA PUMP)
3.INSPECT LEVEL SENSOR (UREA PUMP)
a.
A355506C07
1.479,1.74 1.979,1.177 false 2.51,1.708 2.083,1 false 0.135,0.135 0.448,0.333 0.313,0.198 10 false *a 1.333,1.771 1.708,1.938 0.375,0.167 10 false LVU 2.448,1.74 2.823,1.906 0.375,0.167 10 false ELU
*a Component without harness connected
(Level Sensor (Urea Pump))


Disconnect the level sensor (urea pump) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
14 (LVU) - 6 (ELU) Ignition switch off 1.40 to 89.94 kΩ



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (LEVEL SENSOR (UREA PUMP) POWER SOURCE VOLTAGE)

NG

10.REPLACE LEVEL SENSOR (UREA PUMP)
4.CHECK HARNESS AND CONNECTOR (LEVEL SENSOR (UREA PUMP) POWER SOURCE VOLTAGE)
a.
A360358C14
1.479,0.833 1.896,1.094 0.417,0.26 1.469,1.823 1.125,2.542 true 1.552,1.615 1.99,2.552 true 0.146,0.177 0.458,0.375 0.313,0.198 10 false *a 1.573,0.896 1.885,1.094 0.313,0.198 10 false P11 1.906,2.583 2.646,2.781 0.74,0.198 10 false ELU 0.99,2.583 1.729,2.781 0.74,0.198 10 false LVU
*a Front view of wire harness connector
(to Level Sensor (Urea Pump))


Disconnect the level sensor (urea pump) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
P11-14 (LVU) - P11-6 (ELU) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

5.CLEAR DTC

NG

7.CHECK HARNESS AND CONNECTOR (LEVEL SENSOR (UREA PUMP) - DCU (EMISSION CONTROL ECU ASSEMBLY))
5.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P203C11 OR P203D15)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P203C11 OR P203D15)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

Result:
Result Proceed to
DTC P203C11 or P203D15 is output A
DTCs are not output B




A

8.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)

B

END

7.CHECK HARNESS AND CONNECTOR (LEVEL SENSOR (UREA PUMP) - DCU (EMISSION CONTROL ECU ASSEMBLY))
a.
A405886C01
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


A405887C01
1.521,0.125 1.885,0.396 0.365,0.271 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 1.677,0.198 1.833,0.396 0.156,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


Connect the level sensor (urea pump) connector.


b.

Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-58 (LVU) -E-36 (ELU) Ignition switch off 1.40 to 89.94 kΩ



Result:
Proceed to
OK
NG



OK

8.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)
a.

Replace the DCU (emission control ECU assembly).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

13.CLEAR DTC
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CLEAR DTC
10.REPLACE LEVEL SENSOR (UREA PUMP)
a.

Replace the level sensor (urea pump).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

13.CLEAR DTC
11.REPAIR OR REPLACE LEVEL SENSOR (UREA PUMP)
a.

Clean the sensing part of the level sensor (urea pump).

HINT:

If the level sensor (urea pump) is damaged, replace it.



Result:
Proceed to
NEXT



NEXT

13.CLEAR DTC
12.CONNECT SECURELY
a.

Securely connect the level sensor (urea pump) connector.

HINT:

Repair parts as necessary.



Result:
Proceed to
NEXT



NEXT

13.CLEAR DTC
13.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P203C11 OR P203D15)
14.CHECK WHETHER DTC OUTPUT RECURS (DTC P203C11 OR P203D15)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

OK:

DTCs are not output



Result:
Proceed to
NEXT



NEXT

END