Home › Engine / Hybrid System › N04C-WA (EMISSION CONTROL) › UREA SELECTIVE CATALYTIC REDUCTION SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082614 N04C-WA EMISSION CONTROL _0400651 UREA SELECTIVE CATALYTIC REDUCTION SYSTEM C

N04C-WA EMISSION CONTROL  UREA SELECTIVE CATALYTIC REDUCTION SYSTEM  P205B62  Reductant Tank Temperature Sensor "A" Circuit Range/Performance Signal Compare Failure  


DESCRIPTION

Temperature sensor (urea pump) rationality is checked by comparison with engine coolant temperature.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
P205B62 Reductant Tank Temperature Sensor "A" Circuit Range/Performance Signal Compare Failure Diagnosis Condition:
·

Ignition switch ON.

·

The difference between the SCR inlet exhaust gas temperature and the engine coolant temperature is less than 8°C (14.4°F).

·

The current engine coolant temperature is lower than the engine coolant temperature the last time the ignition switch was turned off by 20°C (36°F) or more.


Malfunction Status:
·

The difference between the temperature sensor (urea pump) and the temperature sensor (urea sensor assembly) is 30°C (54°F) or more, and also the difference between the engine coolant temperature and the temperature sensor (urea pump) is more than 42°C (75.6°F).


Malfunction Duration:
·

50 seconds or more.


·

Open or short in temperature sensor (urea pump) circuit

·

Temperature sensor (urea pump)

·

DCU (emission control ECU assembly)


Class B1 AdBlue consumption warning light:
Comes on
DTC stored

MONITOR DESCRIPTION

Description of malfunction

Temperature sensor (urea pump) malfunction detected.


Reset condition

When the ignition switch is ON, the difference between the temperature sensor (urea pump) and the engine coolant temperature is less than 42°C (75.6°F), and also that the difference between the temperature sensor (urea sensor assembly) and temperature sensor (urea pump) is 30°C (54°F) or less.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P205B62 After warming up the engine, turn the ignition switch off. After the engine sufficiently cools, turn the ignition switch to ON for 50 seconds or more.

WIRING DIAGRAM

A407162E04
0.333,2.146 2.51,2.365 2.177,0.219 10 false Temperature Sensor (Urea Pump) 0.333,1.969 0.646,2.167 0.313,0.198 10 false P11 1.948,0.781 2.26,0.979 0.313,0.198 10 false 1 1.938,1.365 2.25,1.563 0.313,0.198 10 false 2 4.865,0.917 5.177,1.115 0.313,0.198 10 false P12 4.854,1.5 5.167,1.698 0.313,0.198 10 false P12 5.25,0.927 5.76,1.125 0.51,0.198 10 false THU 4.906,0.729 5.219,0.927 0.313,0.198 10 false 54 4.906,1.323 5.219,1.521 0.313,0.198 10 false 43 4.469,0.917 4.781,1.115 0.313,0.198 10 false E-54 4.469,1.5 4.885,1.698 0.417,0.198 10 false E-43 4.563,2.406 7.042,2.615 2.479,0.208 10 false DCU (Emission Control ECU Assembly) 5.25,1.5 5.76,1.698 0.51,0.198 10 false ETHU 1.563,0.833 2.073,1.031 0.51,0.198 10 false THU 1.479,1.302 1.99,1.5 0.51,0.198 10 false ETHU

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (REDUCTANT TEMPERATURE AND REDUCTANT TANK TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Data List / Reductant Temperature and Reductant Tank Temperature.


e.

Read the value.

OK:

The difference between the Reductant Temperature and the Reductant Tank Temperature is 4°C (7.2°F) or less.



Result:
Proceed to
OK
NG


HINT:
·

[Reductant Temperature] indicates urea solution temperature integrated in the urea pump.

·

[Reductant Tank Temperature] indicates urea solution temperature integrated in the urea sensor assembly.




OK

11.CLEAR DTC

NG

2.CHECK CONNECTOR CONNECTION CONDITION (TEMPERATURE SENSOR (UREA PUMP))
2.CHECK CONNECTOR CONNECTION CONDITION (TEMPERATURE SENSOR (UREA PUMP))
a.

Check the connector connection and contact pressure of the temperature sensor (urea pump) connector.

OK:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTOR CONNECTION CONDITION (DCU (EMISSION CONTROL ECU ASSEMBLY))

NG

10.CONNECT SECURELY
3.CHECK CONNECTOR CONNECTION CONDITION (DCU (EMISSION CONTROL ECU ASSEMBLY))
a.

Check the connector connection and contact pressure of the DCU (emission control ECU assembly) connector.

OK:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

4.INSPECT TEMPERATURE SENSOR (UREA PUMP)

NG

9.CONNECT SECURELY
4.INSPECT TEMPERATURE SENSOR (UREA PUMP)
a.

Inspect the temperature sensor (urea pump).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (TEMPERATURE SENSOR (UREA PUMP) - DCU (EMISSION CONTROL ECU ASSEMBLY))

NG

8.REPLACE TEMPERATURE SENSOR (UREA PUMP)
5.CHECK HARNESS AND CONNECTOR (TEMPERATURE SENSOR (UREA PUMP) - DCU (EMISSION CONTROL ECU ASSEMBLY))
a.
A405887C01
1.521,0.125 1.885,0.396 0.365,0.271 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 1.677,0.198 1.833,0.396 0.156,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


Connect the temperature sensor (urea pump) connector.


b.

Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-54 (THU) -E-43 (ETHU) 20°C 2.468 to 2.556 kΩ
40°C 1.155 to 1.205 kΩ



Result:
Proceed to
OK
NG



OK

6.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)
a.

Replace the DCU (emission control ECU assembly).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CLEAR DTC
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

11.CLEAR DTC
8.REPLACE TEMPERATURE SENSOR (UREA PUMP)
a.

Replace the temperature sensor (urea pump).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CLEAR DTC
9.CONNECT SECURELY
a.

Securely connect the DCU (emission control ECU assembly) connector.

HINT:

Repair parts as necessary.



Result:
Proceed to
NEXT



NEXT

11.CLEAR DTC
10.CONNECT SECURELY
a.

Securely connect the temperature sensor (urea pump) connector.

HINT:

Repair parts as necessary.



Result:
Proceed to
NEXT



NEXT

11.CLEAR DTC
11.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (DTC P205B62)
12.CHECK WHETHER DTC OUTPUT RECURS (DTC P205B62)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

OK:

DTCs are not output



Result:
Proceed to
NEXT



NEXT

END