Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) › from 2019.08
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356878 ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)  C1210  Zero Point Calibration of Yaw Rate Sensor Undone  C1336  Zero Point Calibration of Acceleration Sensor Undone  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag ECU assembly) via CAN communication.

If there is a malfunction in the bus lines between the yaw rate and acceleration sensor (airbag ECU assembly) and the CAN communication system, DTC U0124 (Lost Communication with Lateral Acceleration Sensor Module) is output. When DTC U0124 is output together with C1210 and/or C1336, inspect and repair the trouble areas indicated by U0124 first.

These DTCs are also output when the calibration has not been completed.

DTC No. DTC Detection Condition Trouble Area
C1210 Zero point calibration of yaw rate sensor undone.
·

Sensor installation

·

Yaw rate sensor (Airbag ECU assembly)

·

Skid control ECU (Brake actuator assembly)


C1336 Zero point calibration of acceleration sensor undone.
·

Sensor installation

·

Acceleration sensor (Airbag ECU assembly)

·

Skid control ECU (Brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:

When replacing the yaw rate and acceleration sensor (airbag ECU assembly), perform zero point calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>CALIBRATION).


HINT:

When U0124 is output along with C1210 and/or C1336, inspect and repair trouble areas indicated by U0124 first (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>U0073).


PROCEDURE

1.PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR
a.

Perform zero point calibration of the yaw rate and acceleration sensor (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>CALIBRATION).


Result:
Proceed to
NEXT



NEXT

2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Turn the ignition switch off.


b.

Using the GTS, perform a Test Mode (signal check) inspection sensor check and check that all Test Mode (signal check) inspection items change from incomplete to complete (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>TEST MODE PROCEDURE).

OK:

All Test Mode (signal check) inspection items change from incomplete to complete.



Result:
Proceed to
OK
NG



OK

END

NG

3.CHECK AIRBAG ECU ASSEMBLY INSTALLATION
3.CHECK AIRBAG ECU ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the yaw rate and acceleration sensor (airbag ECU assembly) has been installed properly (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG ECU>INSTALLATION).

OK:

The sensor should be tightened to the specified torque.

The sensor should not be installed in a tilted position.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (YAW RATE AND ACCELERATION SENSOR)

NG

INSTALL AIRBAG ECU ASSEMBLY CORRECTLY

4.READ VALUE USING GTS (YAW RATE AND ACCELERATION SENSOR)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Deceleration Sensor Acceleration sensor / Min.: -18.525 m/s2, Max.: 18.387 m/s2 - During deceleration/acceleration: Changes continuously
Deceleration Sensor2 Acceleration sensor 2 / Min.: -18.525 m/s2, Max.: 18.387 m/s2 - During deceleration/acceleration: Changes continuously
Yaw Rate Sensor Yaw rate sensor / Min.: -128°/s, Max.: 127°/s Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-


g.

Check the yaw rate and acceleration sensor (airbag ECU assembly) output value displayed on the GTS.

OK:

The yaw rate and acceleration sensor (airbag ECU assembly) output value is normal.


Result:
Proceed to
OK
NG


NOTICE:

Check the yaw rate and acceleration sensor signal after replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>TEST MODE PROCEDURE).




OK

NG