Home › Vehicle Exterior › WINDOW / GLASS › REAR SIDE WINDOW GLASS (for No. 3 RH) › from 2019.08
RM2850E _59 Vehicle Exterior _073195 WINDOW / GLASS _0356217 REAR SIDE WINDOW GLASS(for No. 3 RH) A

WINDOW / GLASS  REAR SIDE WINDOW GLASS(for No. 3 RH)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for RHD vehicles.



PROCEDURE

Hide 1.INSTALL REAR SIDE FRONT WINDOW GLASS RH

a.

Clean and shape the contact surface of the vehicle body.

i.
B455055C06
0.583,1.177 0.583,1.448 false 0.5,1.479 0.813,1.677 0.313,0.198 10 false *a 3.115,0.375 3.26,0.552 0.146,0.177 10 false a
*a Vehicle Body
V100155

Adhesive


On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

Standard Dimension:
Area Specified Condition
a 1.0 to 3.0 mm (0.0394 to 0.118 in.)



ii.

Clean the contact surface of the vehicle body with non-residue solvent.



b.

Using non-residue solvent, clean the rear side front window glass RH installation surface of the vehicle body.


c.

Install the body primer to the rear side front window glass RH installation surface of the vehicle body.

NOTICE:
·

Do not apply too much primer.

·

Do not apply primer to the adhesive.

·

When applying the primer, take care of the seams of the panel and spot welds.




d.

Install the suction cups to the rear side front window glass RH.


e.

for Slide Type:

i.

Using a brush or sponge, apply primer to the contact surface of the rear side front window glass RH.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.



B475092C02
1.073,0.927 1.229,1.125 0.156,0.198 10 false A 1.073,1.323 1.229,1.521 0.156,0.198 10 false A 0.354,1.74 0.521,1.906 0.167,0.167 10 false B 0.771,1.74 0.927,1.906 0.156,0.167 10 false B 2.396,2.49 2.552,2.688 0.156,0.198 10 false C 2.396,2.885 2.552,3.083 0.156,0.198 10 false C 2.969,2.125 3.125,2.323 0.156,0.198 10 false D 3.344,2.125 3.5,2.323 0.156,0.198 10 false D 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 3.906,0.344 4.24,0.51 0.333,0.167 10 false A-A 3.927,2.125 4.26,2.292 0.333,0.167 10 false C-C 5.615,0.344 5.948,0.51 0.333,0.167 10 false B-B 5.604,2.115 5.938,2.281 0.333,0.167 10 false D-D
*a Backside - -
V100155

Primer Application Area - -



ii.

Apply adhesive to the rear side front window glass RH.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or Equivalent



iii.
B214800C84
1.354,0.583 1.177,0.479 false 2.917,0.375 2.521,0.542 true 0.583,0.667 0.74,0.854 0.156,0.188 10 false a 1.271,1.448 1.417,1.635 0.146,0.188 10 false a 1.125,0.865 1.25,1.063 0.125,0.198 10 false b 0.771,1.031 0.917,1.177 0.146,0.146 10 false b 1.406,0.531 1.604,0.698 0.198,0.167 10 false *b 2.979,0.302 3.177,0.469 0.198,0.167 10 false *a
*a Sealer Gun
*b Nozzle
V100155

Adhesive


Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension:
Area Specified Condition
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)



iv.

Apply adhesive to the rear side front window glass RH as shown in the illustration.

NOTICE:

Allow the primer to dry for 3 minutes or more.


B475088C01
4.25,1.25 4.438,1.198 false 5.938,1.25 6.125,1.198 false 4.635,2.917 4.833,2.948 false 6.313,2.917 6.51,2.948 false 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 1.083,0.927 1.25,1.094 0.167,0.167 10 false A 1.083,1.323 1.25,1.49 0.167,0.167 10 false A 0.365,1.74 0.531,1.906 0.167,0.167 10 false B 0.771,1.76 0.938,1.927 0.167,0.167 10 false B 2.396,2.49 2.563,2.656 0.167,0.167 10 false C 2.396,2.875 2.563,3.042 0.167,0.167 10 false C 2.969,2.135 3.135,2.302 0.167,0.167 10 false D 3.365,2.135 3.531,2.302 0.167,0.167 10 false D 3.896,0.344 4.292,0.51 0.396,0.167 10 false A-A 5.604,0.333 6,0.5 0.396,0.167 10 false B-B 3.906,2.104 4.302,2.271 0.396,0.167 10 false C-C 5.594,2.104 5.99,2.271 0.396,0.167 10 false D-D 4.469,0.667 4.635,0.833 0.167,0.167 10 false a 6.24,0.677 6.406,0.844 0.167,0.167 10 false b 4.521,2.406 4.688,2.573 0.167,0.167 10 false a 6.552,2.583 6.719,2.75 0.167,0.167 10 false c 6.063,2.26 6.229,2.427 0.167,0.167 10 false d 4.052,1.188 4.271,1.354 0.219,0.167 10 false *b 5.771,1.208 5.99,1.375 0.219,0.167 10 false *b 4.875,2.896 5.094,3.063 0.219,0.167 10 false *b 6.573,2.885 6.792,3.052 0.219,0.167 10 false *b
*a Backside *b R End
V100155

Adhesive - -


Standard Dimension:
Area Specified Condition
a 9.0 mm (0.354 in.)
b 13.0 mm (0.512 in.)
c 5.0 mm (0.197 in.)




f.

Fixed Type:

i.

Using a brush or sponge, apply glass primer to the contact surface of the rear side front window glass RH.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.



B475080C01
0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 2.125,0.948 2.281,1.146 0.156,0.198 10 false A 2.125,1.344 2.281,1.542 0.156,0.198 10 false A 0.302,1.625 0.458,1.823 0.156,0.198 10 false B 0.667,1.625 0.823,1.823 0.156,0.198 10 false B 2.177,2.542 2.333,2.74 0.156,0.198 10 false C 2.177,2.927 2.333,3.125 0.156,0.198 10 false C 2.99,2.229 3.146,2.427 0.156,0.198 10 false D 3.406,2.229 3.563,2.427 0.156,0.198 10 false D 3.896,0.333 4.24,0.5 0.344,0.167 10 false A-A 5.604,0.333 5.948,0.5 0.344,0.167 10 false B-B 3.885,2.115 4.229,2.281 0.344,0.167 10 false C-C 5.594,2.104 5.938,2.271 0.344,0.167 10 false D-D
*a Backside - -
V100155

Glass Primer Application Area - -



ii.

Apply adhesive to the rear side front window glass RH.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or Equivalent



iii.
B214800C84
1.354,0.583 1.177,0.479 false 2.917,0.375 2.521,0.542 true 0.583,0.667 0.74,0.854 0.156,0.188 10 false a 1.271,1.448 1.417,1.635 0.146,0.188 10 false a 1.125,0.865 1.25,1.063 0.125,0.198 10 false b 0.771,1.031 0.917,1.177 0.146,0.146 10 false b 1.406,0.531 1.604,0.698 0.198,0.167 10 false *b 2.979,0.302 3.177,0.469 0.198,0.167 10 false *a
*a Sealer Gun
*b Nozzle
V100155

Adhesive


Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension Dimension:
Area Specified Condition
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)



iv.

Apply adhesive to the rear side front window glass RH as shown in the illustration.

NOTICE:

Allow the primer to dry for 3 minutes or more.


B475084C01
4.51,1.417 4.625,1 true 6.219,1.427 6.333,1.021 true 4.354,3.198 4.469,2.781 true 6.094,2.792 5.885,3.156 5.885,3.156 5.979,2.781 true 0.135,0.104 0.375,0.271 0.24,0.167 10 false *a 2.135,0.948 2.375,1.115 0.24,0.167 10 false A 2.135,1.344 2.375,1.51 0.24,0.167 10 false A 0.302,1.656 0.448,1.833 0.146,0.177 10 false B 0.677,1.656 0.823,1.833 0.146,0.177 10 false B 2.177,2.552 2.323,2.729 0.146,0.177 10 false C 2.177,2.938 2.323,3.115 0.146,0.177 10 false C 2.99,2.25 3.135,2.427 0.146,0.177 10 false D 3.396,2.24 3.542,2.417 0.146,0.177 10 false D 3.875,0.333 4.208,0.5 0.333,0.167 10 false A-A 5.615,0.333 5.948,0.5 0.333,0.167 10 false B-B 3.885,2.125 4.219,2.292 0.333,0.167 10 false C-C 5.615,2.115 5.948,2.281 0.333,0.167 10 false D-D 4.417,1.458 4.656,1.625 0.24,0.167 10 false *b 6.135,1.458 6.375,1.625 0.24,0.167 10 false *b 4.281,3.229 4.521,3.396 0.24,0.167 10 false *b 5.813,3.198 6.052,3.365 0.24,0.167 10 false *b
*a Backside *b Adhesive Center
V100155

Adhesive - -




g.

Install the rear side front window glass RH to the vehicle body.


h.

Using suction cups, attach the 4 side window glass spacers and install the rear side front window glass RH.

i.
B474362

for Long Body:


ii.
B474363

for Standard Body, for Super Long Body:



i.

Press it in gently along the rim.

NOTICE:
·

Check that the spacers, retainers are attached to the vehicle body correctly.

·

Check that the vehicle body and glass have a small gap between them.



HINT:

Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.



j.

Using a scraper, remove any excess or protruding adhesive.

NOTICE:

Apply adhesive to the glass rim.



Hide 2.INSPECT FOR LEAKS AND REPAIR

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 62451C 3.INSTALL REAR ROOF SIDE RAIL GARNISH RH (for Long Body, w/o Rear Air Duct)

Hide 62431F 4.INSTALL ROOF SIDE RAIL GARNISH (for Long Body, w/o Rear Air Duct)

Hide 62451E 5.INSTALL REAR ROOF SIDE RAIL GARNISH (w/o Rear Air Duct)

Hide 62451B 6.INSTALL NO. 3 ROOF SIDE RAIL GARNISH RH (w/o Rear Air Duct)

Hide 63372G 7.INSTALL NO. 4 ROOF BOARD SET MOULDING (w/o Rear Air Duct)

Hide 63378C 8.INSTALL NO. 3 ROOF HEADLINING MOULDING (w/o Rear Air Duct)

Hide 63377C 9.INSTALL NO. 2 ROOF HEADLINING MOULDING (w/o Rear Air Duct)

Hide 63372A 10.INSTALL NO. 2 ROOF BOARD SET MOULDING (w/o Rear Air Duct)

Hide 63316A 12.INSTALL NO. 6 ROOF HEADLINING

Hide 62511R 13.INSTALL REAR BODY REAR INSIDE TRIM RH

Hide 62227 14.INSTALL QUARTER PILLAR COVER RH

Hide 62471D 15.INSTALL REAR UPPER PILLAR GARNISH RH

Hide 62472D 16.INSTALL REAR UPPER PILLAR GARNISH LH

Hide 62487A 17.INSTALL INNER ROOF SIDE GARNISH COVER RH (for Double Swing Out Type)

Hide 62488A 18.INSTALL INNER ROOF SIDE GARNISH COVER LH (for Double Swing Out Type)

Hide 63349A 19.INSTALL REAR ROOF HEADLINING GARNISH (for Double Swing Out Type)

Hide 65905B 20.INSTALL WINDOW CURTAIN RAIL SUB-ASSEMBLY (for Lift Up Type, w/ Curtain)

Hide 64735A 21.INSTALL CENTER BACK INNER RAIL GARNISH (for Lift Up Type)

Hide 66301D 22.INSTALL ROPE HOOK SUB-ASSEMBLY (w/ Rope Hook)

Hide 58614A 23.INSTALL NO. 4 MAT SET PLATE

Hide 63917 24.INSTALL NO. 3 INNER COOLER DUCT RH (w/ Rear Air Duct)

Hide 63930 25.INSTALL NO. 4 INNER COOLER DUCT RH (for Super Long Body)

Hide 63930 26.INSTALL NO. 4 INNER COOLER DUCT RH (for Long Body, w/ Rear Air Duc)

Hide 63323 27.INSTALL NO. 3 ROOF BOARD (w/ Rear Air Duct)

Hide 65936 28.INSTALL NO. 1 CURTAIN RAIL (w/ Curtain)

Hide 65939 29.INSTALL NO. 4 CURTAIN RAIL (w/ Curtain)

Hide 63324 30.INSTALL NO. 4 ROOF BOARD (for Super Long Body)

Hide 63324 31.INSTALL NO. 4 ROOF BOARD (for Long Body, w/ Rear Air Duct)

Hide 63372A 32.INSTALL NO. 2 ROOF BOARD SET MOULDING (for Super Long Body)

Hide 63372F 33.INSTALL NO. 3 ROOF BOARD SET MOULDING (w/ Rear Air Duct)

Hide 63372A 34.INSTALL NO. 2 ROOF BOARD SET MOULDING (w/ Rear Air Duct)

Hide 35.INSTALL ROOM RACK ASSEMBLY (w/ Room Rack)

Hide 45619K 36.INSTALL KNUCKLE STOPPER COVER (w/ Room Rack)

Hide 37.INSTALL REAR SEAT ASSEMBLY (for Rear End)