Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for RHD vehicles.
1.INSTALL REAR SIDE FRONT WINDOW GLASS LH
Clean and shape the contact surface of the vehicle body.
| *a | Vehicle Body |
|
Adhesive |
On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.
| Area | Specified Condition |
|---|---|
| a | 1.0 to 3.0 mm (0.0394 to 0.118 in.) |
Clean the contact surface of the vehicle body with non-residue solvent.
Using non-residue solvent, clean the rear side front window glass LH installation surface of the vehicle body.
Install the body primer to the rear side front window glass LH installation surface of the vehicle body.
Do not apply too much primer.
Do not apply primer to the adhesive.
When applying the primer, take care of the seams of the panel and spot welds.
Install the suction cups to the rear side front window glass LH.
for Slide Type:
Using a brush or sponge, apply primer to the contact surface of the rear side front window glass LH.
Do not apply too much primer.
Allow the primer to dry for 3 minutes or more.
| *a | Backside | - | - |
|
Primer Application Area | - | - |
Apply adhesive to the rear side front window glass LH.
Toyota Genuine Windshield Glass Adhesive or Equivalent
| *a | Sealer Gun |
| *b | Nozzle |
|
Adhesive |
Cut off the tip of the cartridge nozzle as shown in the illustration.
| Area | Specified Condition |
|---|---|
| a | 12.0 mm (0.472 in.) |
| b | 8.0 mm (0.315 in.) |
Apply adhesive to the rear side front window glass LH as shown in the illustration.
Allow the primer to dry for 3 minutes or more.
| *a | Backside | *b | R End |
|
Adhesive | - | - |
| Area | Specified Condition |
|---|---|
| a | 9.0 mm (0.354 in.) |
| b | 13.0 mm (0.512 in.) |
| c | 5.0 mm (0.197 in.) |
Fixed Type:
Using a brush or sponge, apply glass primer to the contact surface of the rear side front window glass LH.
Do not apply too much primer.
Allow the primer to dry for 3 minutes or more.
| *a | Backside | - | - |
|
Glass Primer Application Area | - | - |
Apply adhesive to the rear side front window glass LH.
Toyota Genuine Windshield Glass Adhesive or Equivalent
| *a | Sealer Gun |
| *b | Nozzle |
|
Adhesive |
Cut off the tip of the cartridge nozzle as shown in the illustration.
| Area | Specified Condition |
|---|---|
| a | 12.0 mm (0.472 in.) |
| b | 8.0 mm (0.315 in.) |
Apply adhesive to the rear side front window glass LH as shown in the illustration.
Allow the primer to dry for 3 minutes or more.
| *a | Backside | *b | Adhesive Center |
|
Adhesive | - | - |
Install the rear side front window glass LH to the vehicle body.
Using suction cups, attach the 4 side window glass spacers and install the rear side front window glass LH.
for Long Body:
for Standard Body, for Super Long Body:
Press it in gently along the rim.
Check that the spacers, retainers are attached to the vehicle body correctly.
Check that the vehicle body and glass have a small gap between them.
Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.
Using a scraper, remove any excess or protruding adhesive.
Apply adhesive to the glass rim.
2.INSTALL INSPECT FOR LEAKS AND REPAIR
After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
If water leaks into the cabin, allow the water to dry and add adhesive.
Remove the protective tape.
62451E
3.INSTALL REAR ROOF SIDE RAIL GARNISH (w/o Rear Air Duct)
62431F
4.INSTALL ROOF SIDE RAIL GARNISH (for Long Body, w/o Rear Air Duct)
62452B
5.INSTALL NO. 3 ROOF SIDE RAIL GARNISH LH (w/o Rear Air Duct)
63372G
6.INSTALL NO. 4 ROOF BOARD SET MOULDING (w/o Rear Air Duct)
63378C
7.INSTALL NO. 3 ROOF HEADLINING MOULDING (w/o Rear Air Duct)
63377C
8.INSTALL NO. 2 ROOF HEADLINING MOULDING (w/o Rear Air Duct)
62452C
9.INSTALL REAR ROOF SIDE RAIL GARNISH LH (w/o Rear Air Duct)
63372A
10.INSTALL NO. 2 ROOF BOARD SET MOULDING (w/o Rear Air Duct)
11.INSTALL SIDE PANEL
for RHD:
Click hereVehicle Interior>INTERIOR>SIDE PANEL (for RHD)>INSTALLATION
for LHD:
Click hereVehicle Interior>INTERIOR>SIDE PANEL (for LHD)>INSTALLATION
63316A
12.INSTALL NO. 6 ROOF HEADLINING
62512R
13.INSTALL REAR BODY REAR INSIDE TRIM LH
62228
14.INSTALL LOWER QUARTER PILLAR COVER LH
62471D
15.INSTALL REAR UPPER PILLAR GARNISH RH
62472D
16.INSTALL REAR UPPER PILLAR GARNISH LH
62487A
17.INSTALL INNER ROOF SIDE GARNISH COVER RH (for Double Swing Out Type)
62488A
18.INSTALL INNER ROOF SIDE GARNISH COVER LH (for Double Swing Out Type)
63349A
19.INSTALL REAR ROOF HEADLINING GARNISH (for Double Swing Out Type)
65905B
20.INSTALL WINDOW CURTAIN RAIL SUB-ASSEMBLY (for Lift Up Type, w/ curtain)
64735A
21.INSTALL CENTER BACK INNER RAIL GARNISH (for Lift Up Type)
66301D
22.INSTALL ROPE HOOK SUB-ASSEMBLY (w/ Rope Hook)
58614A
23.INSTALL NO. 4 MAT SET PLATE
63917A
24.INSTALL NO. 3 INNER COOLER DUCT LH
63940
25.INSTALL NO. 4 INNER COOLER DUCT LH (for Super Long Body)
63940
26.INSTALL NO. 4 INNER COOLER DUCT LH (for Long Body, w/ Rear Air Duc)
63323
27.INSTALL NO. 3 ROOF BOARD (w/ Rear Air Duct)
65936
28.INSTALL NO. 1 CURTAIN RAIL (w/ Curtain)
65937
29.INSTALL NO. 2 CURTAIN RAIL (w/ Curtain)
63324
30.INSTALL NO. 4 ROOF BOARD (for Super Long Body)
63324
31.INSTALL NO. 4 ROOF BOARD (for Long Body, w/ Rear Air Duc)
63372A
32.INSTALL NO. 2 ROOF BOARD SET MOULDING (for Super Long Body)
63372F
33.INSTALL NO. 3 ROOF BOARD SET MOULDING (w/ Rear Air Duct)
63372A
34.INSTALL NO. 2 ROOF BOARD SET MOULDING (w/ Rear Air Duct)
35.INSTALL ROOM RACK ASSEMBLY (w/ Room Rack)
45619K
36.INSTALL KNUCKLE STOPPER COVER (w/ Room Rack)
37.INSTALL REAR SEAT ASSEMBLY (for Rear End)
for Tumble Type 4-Passenger Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Tumble Type 4-Passenger Seat)>INSTALLATION
for Fixed Type 4-Passenger Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Fixed Type 4-Passenger Seat)>INSTALLATION