Home › Vehicle Exterior › WINDOW / GLASS › BACK WINDOW GLASS (for Double Swing Out Type) › from 2019.08
RM2850E _59 Vehicle Exterior _073195 WINDOW / GLASS _0356207 BACK WINDOW GLASS(for Double Swing Out Type) A

WINDOW / GLASS  BACK WINDOW GLASS(for Double Swing Out Type)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for RHD vehicles.

·

Use the same procedure for RH and LH sides.

·

The procedure listed below is for LH side.



PROCEDURE

Hide 68294A 1.INSTALL BACK DOOR GLASS ADHESIVE DAM

a.

Using non-residue solvent, clean the back door glass adhesive dam installation surface of the back window corner glass LH.


b.

Install the glass primer to the back door glass adhesive dam installation surface of the back window corner glass LH.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

Remove the peeling paper from a new back door glass adhesive dam.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



d.

Install the 3 back door glass adhesive dams to the back window corner glass LH as shown in the illustration.

B471611C01
1.031,2 0.75,2.115 0.75,2.115 0.781,2.031 true 3.271,0.75 3.458,0.938 3.458,0.938 3.281,0.969 true 3.365,1.74 3.729,1.854 3.729,1.854 3.375,1.969 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 1.125,1.635 1.281,1.802 0.156,0.167 10 true B 1.208,2.177 1.365,2.344 0.156,0.167 10 true B 2.979,0.479 3.135,0.646 0.156,0.167 10 true A 3.5,0.458 3.656,0.625 0.156,0.167 10 true A 0.583,2.073 0.792,2.24 0.208,0.167 10 false *b 3.51,0.906 3.719,1.073 0.208,0.167 10 false *b 3.781,1.781 3.99,1.948 0.208,0.167 10 false *b 5,0.115 5.313,0.292 0.313,0.177 10 false A-A 5.042,1.469 5.354,1.646 0.313,0.177 10 false B-B 5.729,0.26 5.854,0.438 0.125,0.177 10 false a 5.75,1.615 5.875,1.792 0.125,0.177 10 false b
*a Backside *b Ceramic Notch


Standard Dimension:
Area Specified Condition
a 20 mm (0.787 in.)
b 19.5 mm (0.768 in.)



Hide 64828 2.INSTALL BACK WINDOW GLASS CLIP LH

a.

Using non-residue solvent, clean the back window glass clip LH installation surface of the back window corner glass LH.


b.

Install the glass primer to the back window glass clip LH installation surface of the back window corner glass LH.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

Remove the peeling paper from a new back window glass clip LH.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



d.
B471612C01
0.542,1.177 0.469,0.781 0.469,0.781 1.083,1.177 true 0.552,1.531 0.854,1.917 0.854,1.917 1.083,1.531 true 2.646,1.125 2.833,1.427 2.833,1.427 2.969,1.135 true 2.625,0.563 3.052,0.281 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 3.083,0.208 3.302,0.375 0.219,0.167 10 false *b 2.75,1.448 2.969,1.615 0.219,0.167 10 false *b 0.771,1.958 0.99,2.125 0.219,0.167 10 false *b 0.292,0.625 0.51,0.792 0.219,0.167 10 false *b
*a Backside
*b Ceramic Notch


Install the 2 back window glass clips LH to the back window corner glass LH as shown in the illustration.


Hide 64813D 3.INSTALL BACK WINDOW GLASS ADHESIVE DAM

a.

Using non-residue solvent, clean the back window glass adhesive dam installation surface of the back window corner glass LH.


b.

Install the glass primer to the back window glass adhesive dam installation surface of the back window corner glass LH.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

Remove the peeling paper from a new back window glass adhesive dam.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



d.
B471613C01
0.698,1.667 0.344,1.052 0.344,1.052 0.667,0.573 true 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 0.156,0.979 0.375,1.146 0.219,0.167 10 false *b 1.479,0.823 1.635,0.979 0.156,0.156 10 false A 1.167,0.823 1.323,0.979 0.156,0.156 10 false A 2.563,0.615 2.719,0.771 0.156,0.156 10 false a 2.344,0.313 2.698,0.469 0.354,0.156 10 false A-A
*a Backside
*b Ceramic Notch


Install the back window glass adhesive dam to the back window corner glass LH as shown in the illustration.

Standard Dimension:
Area Specified Condition
a 4.7 mm (0.185 in.)



Hide 64814A 4.INSTALL BACK WINDOW CORNER GLASS LH

a.

Clean and shape the contact surface of the vehicle body.

i.
B455055C06
0.583,1.177 0.583,1.448 false 0.5,1.479 0.813,1.677 0.313,0.198 10 false *a 3.115,0.375 3.26,0.552 0.146,0.177 10 false a
*a Vehicle Body
V100155

Adhesive


On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

Standard Dimension:
Area Specified Condition
a 1.0 to 3.0 mm (0.0394 to 0.118 in.)



ii.

Clean the contact surface of the vehicle body with non-residue solvent.



b.

Position the back window corner glass LH.

i.

Using suction cups, place the back window corner glass LH in the correct position.


ii.

Check that the entire contact surface of the glass rim is perfectly even.


iii.

Using suction cups, remove the back window corner glass LH.


iv.

Using a brush or sponge, apply body primer to the exposed part of the vehicle body.

NOTICE:
·

Do not apply too much primer.

·

Do not apply primer to the adhesive.

·

When applying the primer, take care of the seams of the panel and spot welds.




v.

Using a brush or sponge, apply glass primer to the contact surface of the glass.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.



B471614C01
0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 1.406,0.198 1.563,0.365 0.156,0.167 10 false A 1.406,0.594 1.563,0.76 0.156,0.167 10 false A 1.063,1.521 1.219,1.688 0.156,0.167 10 false B 1.427,1.521 1.583,1.688 0.156,0.167 10 false B 1.698,3.031 1.854,3.198 0.156,0.167 10 false C 1.75,3.458 1.906,3.625 0.156,0.167 10 false C 2.073,2.417 2.229,2.583 0.156,0.167 10 false D 2.469,2.417 2.625,2.583 0.156,0.167 10 false D 3.865,0.292 4.177,0.458 0.313,0.167 10 false A-A 5.604,0.292 5.917,0.458 0.313,0.167 10 false B-B 3.885,2.073 4.198,2.24 0.313,0.167 10 false C-C 5.583,2.063 5.896,2.229 0.313,0.167 10 false D-D 4.573,0.531 4.708,0.698 0.135,0.167 10 false a 4.854,0.781 4.99,0.948 0.135,0.167 10 false b 6.188,0.667 6.323,0.833 0.135,0.167 10 false c 4.667,2.25 4.802,2.417 0.135,0.167 10 false d 4.958,2.51 5.094,2.677 0.135,0.167 10 false b 6.198,2.281 6.333,2.448 0.135,0.167 10 false e 6.625,2.552 6.76,2.719 0.135,0.167 10 false f
*a Backside - -
V100155

Glass Primer Application Area - -


Standard Dimension:
Area Specified Condition
a 14.0 mm (0.551 in.)
b 6.0 mm (0.236 in.)
c 22.6 mm (0.890 in.)
d 13.5 mm (0.531 in.)
e 22.0 mm (0.866 in.)
f 7.0 mm (0.276 in.)




c.

Apply adhesive to the back window corner glass LH.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or Equivalent



d.
B214800C84
1.354,0.583 1.177,0.479 false 2.917,0.375 2.521,0.542 true 0.583,0.667 0.74,0.854 0.156,0.188 10 false a 1.271,1.448 1.417,1.635 0.146,0.188 10 false a 1.125,0.865 1.25,1.063 0.125,0.198 10 false b 0.771,1.031 0.917,1.177 0.146,0.146 10 false b 1.406,0.531 1.604,0.698 0.198,0.167 10 false *b 2.979,0.302 3.177,0.469 0.198,0.167 10 false *a
*a Sealer Gun
*b Nozzle
V100155

Adhesive


Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension:
Area Specified Condition
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)


HINT:

After cutting off the tip, use all adhesive within the time written in the table below.



e.

Load the sealer gun with the cartridge.


f.

Apply adhesive to the glass as shown in the illustration.

NOTICE:

Allow the primer to dry for 3 minutes or more.


B471615C01
4.74,1.49 4.594,1.25 true 6.458,1.448 6.313,1.208 true 4.667,3.344 4.521,3.104 true 6.26,3.094 6.292,3.344 6.292,3.344 6.115,3.094 true 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 1.396,0.198 1.552,0.354 0.156,0.156 10 false A 1.396,0.583 1.552,0.74 0.156,0.156 10 false A 1.052,1.521 1.208,1.677 0.156,0.156 10 false B 1.448,1.521 1.604,1.677 0.156,0.156 10 false B 1.677,3.031 1.833,3.188 0.156,0.156 10 false C 1.75,3.448 1.906,3.604 0.156,0.156 10 false C 2.073,2.427 2.229,2.583 0.156,0.156 10 false D 2.458,2.417 2.615,2.573 0.156,0.156 10 false D 3.885,0.292 4.208,0.448 0.323,0.156 10 false A-A 5.573,0.292 5.896,0.448 0.323,0.156 10 false B-B 3.875,2.073 4.198,2.229 0.323,0.156 10 false C-C 5.594,2.073 5.917,2.229 0.323,0.156 10 false D-D 4.688,0.646 4.844,0.802 0.156,0.156 10 false a 6.083,0.604 6.24,0.76 0.156,0.156 10 false b 4.604,2.5 4.76,2.656 0.156,0.156 10 false a 6.146,2.302 6.302,2.458 0.156,0.156 10 false c 6.365,2.615 6.521,2.771 0.156,0.156 10 false d 4.729,1.5 5.042,1.698 0.313,0.198 10 false *b 6.448,1.49 6.76,1.688 0.313,0.198 10 false *b 4.677,3.344 4.927,3.5 0.25,0.156 10 false *b 6.302,3.354 6.552,3.51 0.25,0.156 10 false *b
*a Backside *b Adhesive Center
V100155

Adhesive - -


Standard Dimension:
Area Specified Condition
a 13.0 mm (0.512 in.)
b 15.6 mm (0.614 in.)
c 8.0 mm (0.315 in.)
d 14.0 mm (0.551 in.)



g.

Install the back window corner glass LH to the vehicle body.


h.
B471607

Using suction cups, attach the 2 back window glass clips LH and install the back window corner glass LH.


i.

Press it in gently along the rim.

NOTICE:
·

Check that the 2 back window glass clips LH are attached to the vehicle body correctly.

·

Check that the vehicle body and glass have a small gap between them.



HINT:

Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.



j.

Using a scraper, remove any excess or protruding adhesive.

NOTICE:

Apply adhesive to the glass rim.



Hide 5.INSPECT FOR LEAKS AND REPAIR

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 63940 6.INSTALL NO. 4 INNER COOLER DUCT LH (for Long Body)

Hide 63940 7.INSTALL NO. 4 INNER COOLER DUCT LH (for Super Long Body)

Hide 65937 8.INSTALL NO. 2 CURTAIN RAIL (for Long Body, w/ Curtain)

Hide 65937 9.INSTALL NO. 2 CURTAIN RAIL (Super Long Body, w/ Curtain)

Hide 63316A 10.INSTALL NO. 6 ROOF HEADLINING

Hide 62512R 11.INSTALL REAR BODY REAR INSIDE TRIM LH

Hide 62228 12.INSTALL LOWER QUARTER PILLAR COVER LH

Hide 62472D 13.INSTALL REAR UPPER PILLAR GARNISH LH

Hide 62471D 14.INSTALL REAR UPPER PILLAR GARNISH RH

Hide 62488A 15.INSTALL INNER ROOF SIDE GARNISH COVER LH

Hide 62487A 16.INSTALL INNER ROOF SIDE GARNISH COVER RH

Hide 63349A 17.INSTALL REAR ROOF HEADLINING GARNISH

Hide 66301D 18.INSTALL ROPE HOOK SUB-ASSEMBLY (w/ Rope Hook)

Hide 58614A 19.INSTALL NO. 4 MAT SET PLATE

Hide 63324 20.INSTALL NO. 4 ROOF BOARD (for Long Body)

Hide 63324 21.INSTALL NO. 4 ROOF BOARD (for Super Long Body)

Hide 63372F 22.INSTALL NO. 3 ROOF BOARD SET MOULDING

Hide 63372A 23.INSTALL NO. 2 ROOF BOARD SET MOULDING (Super Long Body)

Hide 24.INSTALL ROOM RACK ASSEMBLY (w/ Room Rack)

Hide 45619K 25.INSTALL KNUCKLE STOPPER COVER (w/ Room Rack)

Hide 26.INSTALL REAR SEAT ASSEMBLY (for Rear End)