Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › DIESEL THROTTLE BODY › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0403583 DIESEL THROTTLE BODY A

N04C-WA ENGINE CONTROL  DIESEL THROTTLE BODY  INSTALLATION  


PROCEDURE

Hide 26100 1.INSTALL DIESEL THROTTLE BODY

a.

Remove any seal packing material from the contact surface.


b.
A175532C01
1.802,0.906 1.5,0.167 1.5,0.167 1.417,0.167 true 1.26,0.063 1.469,0.25 0.208,0.188 10 false *a 0.927,1.802 1.219,1.958 0.292,0.156 10 false : *b
*a 70 mm (2.75 in.)
*b Seal Packing


Apply a continuous bead of seal packing (width: 1.5 to 2.5 mm (0.0591 to 0.0984 in.)) as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Remove any oil from contact surface.

·

Install the diesel throttle body within 3 minutes of applying the seal packing.

·

Do not run the engine for at least 2 hours after installation.




c.

Install the diesel throttle body with the 2 bolts and 2 nuts.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


d.

Connect the 2 connectors.


Hide 17030 2.INSTALL AIR HOSE ASSEMBLY

a.
A450234C02
2.625,2.906 2.719,0.917 2.719,0.917 2.865,0.917 true 1.563,0.208 1.875,0.406 0.313,0.198 10 false *a 1.479,3.281 1.792,3.479 0.313,0.198 10 false *a 2,0.906 2.313,1.104 0.313,0.198 10 false *b 1.99,3.771 2.302,3.969 0.313,0.198 10 false *b 2.938,0.833 3.094,1.031 0.156,0.198 10 false A
*a Upper Side
*b RH Side


Connect the air hose assembly and install the bolt.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Tighten the hose clamp (intercooler air hose side) as shown in the illustration.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)

HINT:

Tighten the screw at a rate of 2 seconds per turn.



c.

Tighten the hose clamp (diesel throttle body side) as shown in the illustration.

NOTICE:

Do not remove the hose clamp A.


Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.

Attach the 2 clamps and then connect the vacuum transmitting hose.


Hide 11409 3.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 44379A 4.INSTALL NO. 2 OIL RESERVOIR BRACKET

Hide 44360 5.INSTALL VANE PUMP OIL RESERVOIR ASSEMBLY

Hide 53712C 6.INSTALL FRONT FENDER APRON LH

a.

Install the front fender apron LH with the 6 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 51441D 7.INSTALL NO. 1 ENGINE UNDER COVER

Hide 58701A 8.INSTALL FRONT ENGINE SERVICE COVER PANEL SUB-ASSEMBLY

Hide 33820B 9.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 58841A 10.INSTALL SHIFTING HOLE COVER (for Automatic Transmission)

Hide 58123A 11.INSTALL SHIFT AND SELECT LEVER SUPPORT WITH BOOTS (for Manual Transmission)

Hide 58420 12.INSTALL NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY

Hide 58734B 13.INSTALL REAR ENGINE SERVICE COVER WEATHERSTRIP

Hide 58410 14.INSTALL ENGINE SERVICE HOLE COVER

Hide 58521D 15.INSTALL ENGINE SERVICE HOLE COVER MAT