Prolonged and repeated contact with engine oil will result in the loss of natural oil from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
Wear protective clothing and gloves. Avoid contact with used oil. If contact occurs, wash your skin thoroughly with soap or waterless hand cleaner. Never use gasoline, thinners, or solvents to wash the skin.
In order to protect the environment, dispose of used oil and used oil filters at designated disposal sites only.
58410
1.REMOVE ENGINE SERVICE HOLE COVER
58734B
2.REMOVE REAR ENGINE SERVICE COVER WEATHERSTRIP
3.DRAIN ENGINE OIL
Remove the oil filler cap sub-assembly.
Remove the drain plug and gasket from the oil pan and drain the engine oil into a container.
Clean the drain plug.
Install the drain plug with a new gasket.
15613
4.REMOVE OIL FILTER ELEMENT
| *a | Drain Adapter |
| *b | Pipe |
| *c | Hose |
Connect a hose with an inner diameter of 12 mm (0.472 in.) to the pipe.
Firmly insert the hose until it contacts the base of the drain adapter pipe.
Remove the oil filter plug and O-ring (for plug) from the oil filter cap assembly.
After removing the oil filter plug, a small amount of oil may drip out, so wipe it with a cloth.
| *1 | Oil Filter Cap Assembly |
| *a | Drain Adapter |
| *b | Pipe |
Install the drain adapter and its installed hose to the oil filter cap assembly, and then tighten it until the drain adapter contacts the surface. After making contact, tighten the drain adapter until it can no longer be turned by hand.
Do not install and tighten the drain adapter using tools such as pliers. Otherwise, the drain adapter may be damaged.
Use a container to catch the draining engine oil.
Check that the engine oil has been drained and remove the drain adapter.
Remove the oil filter cap assembly.
| *1 | Oil Filter Element |
| *2 | O-Ring (for cap) |
Remove the oil filter element and O-ring (for cap) from the oil filter cap assembly.
To prevent damage to the O-ring groove, remove the O-ring (for cap) by hand and do not use any tools.
15613
5.INSTALL OIL FILTER ELEMENT
Clean the inside of the oil filter cap assembly, the threads and O-ring groove.
| *1 | O-Ring (for cap) |
| *a | CORRECT |
| *b | INCORRECT |
Apply a light coat of engine oil to a new O-ring (for cap), and install it to the oil filter cap assembly.
Be sure to install the O-ring in the proper position, otherwise engine oil may leak.
Do not twist the O-ring.
Attach a new O-ring after brakes cleaner volatilized enough when use brakes cleaner to prevent the deterioration of the O-ring.
Set a new oil filter element to the oil filter cap assembly.
Remove any dirt or foreign matter from the installation surface and inside of the engine.
Again apply a light coat of engine oil to the O-ring (for cap), and install the oil filter cap assembly.
Make sure that the O-ring (for cap) is not pinched.
| *1 | Oil Filter Cap Assembly |
| *2 | O-Ring (for cap) |
| *3 | Oil Cooler Cover Sub-assembly |
| *a | No Gap |
Tighten the oil filter cap assembly.
After tightening the oil filter cap assembly, check for gaps between the installation surfaces and protrusion of O-ring (for cap).
| *1 | O-Ring (for plug) |
Apply a light coat of engine oil to a new O-ring (for plug), and install it to the oil filter cap assembly.
Remove any dirt or foreign matter from the installation surface.
Install the oil filter plug to the oil filter cap assembly.
Make sure that the O-ring (for plug) is not pinched.
6.ADD ENGINE OIL
Add fresh oil and install the oil filler cap sub-assembly.
| Oil Grade | |
|---|---|
| API CH-4, CI-4 or CI-4 PLUS, ACEA E-4, E-7
JASO DH-1 |
·
5W-30 ·
10W-30 ·
15W-40 |
| Item | Fill amount |
|---|---|
| Drain and refill with oil filter change | 7.0 liters (7.4 US qts, 6.2 Imp. qts) |
| Drain and refill without oil filter change | 5.8 liters (6.1 US qts, 5.1 Imp. qts) |
| Dry fill | 8.4 liters (8.9 US qts, 7.4 Imp. qts) |
7.INSPECT FOR OIL LEAK
Warm up the engine and check for engine oil leaks.
8.CHECK OIL LEVEL
58734B
9.INSTALL REAR ENGINE SERVICE COVER WEATHERSTRIP
58410
10.INSTALL ENGINE SERVICE HOLE COVER