Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › from 2019.08
RM2850E _57 Power Source / Network _073263 CAN COMMUNICATION _0356688 CAN COMMUNICATION SYSTEM C

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  U002988  Vehicle Communication Bus A Performance Bus off  U0073  Control Module Communication Bus OFF  U010031  Lost Communication with ECM/PCM "A" No Signal  U010A  Lost Communication with Exhaust Gas Recirculation Control Module "A"  U010C  Lost Communication with Turbocharger/Supercharger Control Module "A"  U010E  Lost Communication with Reductant Control Module  U029D  Lost Communication with NOx Sensor "A"  U029E  Lost Communication with NOx Sensor "B"  U02A2  Lost Communication with Reductant Quality Module  U02A231  Lost Communication with Reductant Quality Module No Signal  U02A3  Lost Communication with Particulate Matter Sensor  U1001  Lost Communication with Vehicle  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Note
U002988 Vehicle Communication Bus A Performance Bus off The emission control ECU assembly detects a bus off condition (emission local bus side).
·

Local bus main line and branch line

·

All ECUs and sensors in emission local bus

·

CAN junction connector

·

CAN junction terminal


DTC Output from:

Emission control ECU assembly


U0073 Control Module Communication Bus OFF The ECM detects a bus off condition (emission local bus side).
·

Local bus main line and branch line

·

All ECUs and sensors in emission local bus

·

CAN junction connector

·

CAN junction terminal


DTC Output from:

ECM


U010031 Lost Communication with ECM/PCM "A" No Signal The emission control ECU assembly is unable to receive data from the ECM.
·

Local bus main line and branch line

·

All ECUs and sensors in emission local bus

·

CAN junction connector

·

CAN junction terminal


DTC Output from:

Emission control ECU assembly


U010A Lost Communication with Exhaust Gas Recirculation Control Module "A" The ECM is unable to receive data from the EGR valve assembly.
·

Local bus main line and branch line

·

All ECUs and sensors in emission local bus

·

CAN junction connector

·

CAN junction terminal


DTC Output from:

ECM


U010C Lost Communication with Turbocharger/Supercharger Control Module "A" The ECM is unable to receive data from the turbocharger sub-assembly.
·

Local bus main line and branch line

·

All ECUs and sensors in emission local bus

·

CAN junction connector

·

CAN junction terminal


DTC Output from:

ECM


U010E Lost Communication with Reductant Control Module The ECM is unable to receive data from the emission control ECU assembly.
·

Local bus main line and branch line

·

All ECUs and sensors in emission local bus

·

CAN junction connector

·

CAN junction terminal


DTC Output from:

ECM


U029D Lost Communication with NOx Sensor "A" The ECM is unable to receive data from the No. 1 nitrogen oxides sensor.
·

Local bus main line and branch line

·

All ECUs and sensors in emission local bus

·

CAN junction connector

·

CAN junction terminal


DTC Output from:

ECM


U029E Lost Communication with NOx Sensor "B" The ECM is unable to receive data from the No. 2 nitrogen oxides sensor.
·

Local bus main line and branch line

·

All ECUs and sensors in emission local bus

·

CAN junction connector

·

CAN junction terminal


DTC Output from:

ECM


U02A2 Lost Communication with Reductant Quality Module The ECM is unable to receive data from the urea solution quality and temperature sensor.
·

Local bus main line and branch line

·

All ECUs and sensors in emission local bus

·

CAN junction connector

·

CAN junction terminal


DTC Output from:

ECM


U02A231 Lost Communication with Reductant Quality Module No Signal The emission control ECU assembly is unable to receive data from the particulate matter sensor.
·

Local bus main line and branch line

·

All ECUs and sensors in emission local bus

·

CAN junction connector

·

CAN junction terminal


DTC Output from:

Emission control ECU assembly


U02A3 Lost Communication with Particulate Matter Sensor The ECM is unable to receive data from the particulate matter sensor.
·

Local bus main line and branch line

·

All ECUs and sensors in emission local bus

·

CAN junction connector

·

CAN junction terminal


DTC Output from:

ECM


U1001 Lost Communication with Vehicle The ECM detects a bus off condition (emission local bus side).
·

Local bus main line and branch line

·

All ECUs and sensors in emission local bus

·

CAN junction connector

·

CAN junction terminal


DTC Output from:

ECM



WIRING DIAGRAM

C422617E02
0.302,0.844 1.219,1.042 0.917,0.198 10 false A118 0.281,1.01 2.51,1.281 2.229,0.271 10 false No. 4 CAN Junction Terminal 0.979,0.75 1.896,0.948 0.917,0.198 10 false VGND 1.521,0.542 1.833,0.74 0.313,0.198 10 false 2 0.99,0.208 1.906,0.406 0.917,0.198 10 false VOUT 1.5,0.208 1.813,0.406 0.313,0.198 10 false 3 3.708,0.542 4.021,0.74 0.313,0.198 10 false 4 3.698,0.188 4.01,0.385 0.313,0.198 10 false 2 4.396,0.229 4.708,0.427 0.313,0.198 10 false 6 4.396,0.563 4.708,0.76 0.313,0.198 10 false 8 5.688,0.563 6,0.76 0.313,0.198 10 false 5 5.688,0.219 6,0.417 0.313,0.198 10 false 4 5.896,0.302 6.385,0.5 0.49,0.198 10 false CANH 5.885,0.635 6.375,0.833 0.49,0.198 10 false CANL 5.438,0.781 5.927,0.979 0.49,0.198 10 false P13 5.448,0.948 7.063,1.365 1.615,0.417 10 false Urea Sensor Assembly 5.427,2.385 6.063,2.615 0.635,0.229 10 false P12 5.417,2.563 6.875,3.031 1.458,0.469 10 false Emission Control ECU Assembly 5.917,2.198 6.406,2.396 0.49,0.198 10 false CA2L 5.896,1.896 6.385,2.094 0.49,0.198 10 false CA2H 5.646,2.125 5.958,2.323 0.313,0.198 10 false 10 5.635,1.792 5.948,1.99 0.313,0.198 10 false 11 4.417,2.115 4.729,2.313 0.313,0.198 10 false 3 4.417,1.771 4.729,1.969 0.313,0.198 10 false 1 3.698,2.094 4.01,2.292 0.313,0.198 10 false 7 3.698,1.75 4.01,1.948 0.313,0.198 10 false 5 1.5,2.115 1.813,2.313 0.313,0.198 10 false 3 1.5,1.76 1.813,1.958 0.313,0.198 10 false 2 4.448,6.563 5.167,6.781 0.719,0.219 10 false 20 4.438,7.573 5.26,7.771 0.823,0.198 10 false 11 5.385,6.552 5.698,6.75 0.313,0.198 10 false 102 5.438,6.219 5.75,6.417 0.313,0.198 10 false 80 3.396,2.417 4.313,2.615 0.917,0.198 10 false P17 3.385,2.563 4.729,2.948 1.344,0.385 10 false No. 10 CAN Junction Connector 5.677,3.615 5.99,3.813 0.313,0.198 10 false 3 5.688,3.271 6,3.469 0.313,0.198 10 false 2 0.365,5.313 0.854,5.51 0.49,0.198 10 false j5 0.333,5.479 2.167,5.74 1.833,0.26 10 false Turbocharger Sub-assembly 5.885,3.698 6.375,3.896 0.49,0.198 10 false CANL 5.896,3.323 6.385,3.521 0.49,0.198 10 false CANH 5.646,6.948 6.208,7.135 0.563,0.188 10 false B142 5.656,7.094 6.073,7.333 0.417,0.24 10 false ECM 5.188,8.208 5.677,8.406 0.49,0.198 10 false B145 5.198,8.375 7.021,8.688 1.823,0.313 10 false No. 7 CAN Junction Terminal 1.042,6.667 1.531,6.865 0.49,0.198 10 false CANL 1.021,6.344 1.51,6.542 0.49,0.198 10 false CANH 1.51,6.573 1.823,6.771 0.313,0.198 10 false 2 1.521,6.198 1.833,6.396 0.313,0.198 10 false 5 3.104,1.76 3.417,1.958 0.313,0.198 10 false 2 3.094,2.104 3.406,2.302 0.313,0.198 10 false 3 2.417,1.75 2.729,1.948 0.313,0.198 10 false 6 2.417,2.104 2.729,2.302 0.313,0.198 10 false 7 0.292,2.365 1.208,2.563 0.917,0.198 10 false A116 0.281,2.542 2.323,2.74 2.042,0.198 10 false No. 1 Nitrogen Oxides Sensor 1.052,1.885 1.542,2.083 0.49,0.198 10 false CANH 1.063,2.208 1.552,2.406 0.49,0.198 10 false CANL 3.094,3.583 3.406,3.781 0.313,0.198 10 false 4 3.094,3.281 3.406,3.479 0.313,0.198 10 false 1 2.146,3.854 3.063,4.052 0.917,0.198 10 false A121 2.156,4.01 3.427,4.375 1.271,0.365 10 false No. 2 CAN Junction Connector 3.094,5.021 3.406,5.219 0.313,0.198 10 false 8 3.083,4.656 3.396,4.854 0.313,0.198 10 false 6 4.427,3.604 4.74,3.802 0.313,0.198 10 false 7 4.427,3.271 4.74,3.469 0.313,0.198 10 false 5 2.156,6.823 3.073,7.021 0.917,0.198 10 false B118 2.167,7 3.542,7.448 1.375,0.448 10 false No. 5 CAN Junction Connector 2.406,6.542 2.719,6.74 0.313,0.198 10 false 3 2.417,6.198 2.729,6.396 0.313,0.198 10 false 1 3.094,6.542 3.406,6.74 0.313,0.198 10 false 7 3.104,6.219 3.417,6.417 0.313,0.198 10 false 5 0.333,6.813 0.823,7.01 0.49,0.198 10 false B48 0.344,6.99 1.792,7.229 1.448,0.24 10 false EGR Valve Assembly 3.375,8.156 4.292,8.354 0.917,0.198 10 false B149 3.354,8.302 4.583,8.646 1.229,0.344 10 false No. 8 CAN Junction Connector 5.719,6.313 6.635,6.51 0.917,0.198 10 false CAN+ 5.74,6.646 6.656,6.844 0.917,0.198 10 false CAN- 4.417,6.198 4.615,6.427 0.198,0.229 10 false 9 4.469,7.896 5.24,8.094 0.771,0.198 10 false 22 5.521,7.573 5.833,7.771 0.313,0.198 10 false 3 5.542,7.906 5.854,8.104 0.313,0.198 10 false 2 5.729,8.115 6.219,8.313 0.49,0.198 10 false VGND 5.75,7.573 6.24,7.771 0.49,0.198 10 false VOUT 3.698,6.552 3.979,6.792 0.281,0.24 10 false 21 3.688,6.219 3.927,6.427 0.24,0.208 10 false 10 3.74,3.292 4.052,3.49 0.313,0.198 10 false 1 3.729,3.604 4.042,3.802 0.313,0.198 10 false 3 5.51,3.875 6.427,4.073 0.917,0.198 10 false P14 5.521,4.042 7,4.406 1.479,0.365 10 false No. 2 Nitrogen Oxides Sensor 3.74,5.01 4.052,5.208 0.313,0.198 10 false 4 3.74,4.667 4.052,4.865 0.313,0.198 10 false 2 1.521,5.042 1.833,5.24 0.313,0.198 10 false 3 1.51,4.708 1.823,4.906 0.313,0.198 10 false 4 1.01,4.802 1.5,5 0.49,0.198 10 false CANH 1.031,5.156 1.521,5.354 0.49,0.198 10 false CANL 3.458,5.302 4.375,5.5 0.917,0.198 10 false A122 3.469,5.458 5.604,5.781 2.135,0.323 10 false No. 6 CAN Junction Connector 2.417,5.021 2.729,5.219 0.313,0.198 10 false 4 2.417,4.677 2.729,4.875 0.313,0.198 10 false 2 2.406,3.563 2.719,3.76 0.313,0.198 10 false 8 2.396,3.219 2.708,3.417 0.313,0.198 10 false 5 0.25,3.844 1.167,4.042 0.917,0.198 10 false P15 1.01,3.667 1.5,3.865 0.49,0.198 10 false CANL 0.99,3.354 1.479,3.552 0.49,0.198 10 false CANH 1.521,3.594 1.833,3.792 0.313,0.198 10 false 4 1.51,3.25 1.823,3.448 0.313,0.198 10 false 3 0.26,4.01 1.969,4.24 1.708,0.229 10 false Particulate Matter Sensor

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Clear the DTCs.


b.

According to the display on the GTS, select "Health Check".


c.

Read the DTCs.


Result:
Result Proceed to
DTC is not output from ECM or emission control ECU assembly A
DTC U010031 or U02A231 is output from emission control ECU assembly B
DTC U010A, U010C, U010E, U029D, U029E, U02A2 or U02A3 is output from ECM C
·

DTC U002988, U0073 or U1001 is output

·

2 or more of the following DTCs are simultaneously output: U010031, U010A, U010C, U010E, U029D, U029E, U02A2, U02A231 or U02A3


D



A

B

C

D

2.CHECK CAN BUS (NO. 6 CAN JUNCTION CONNECTOR)
2.CHECK CAN BUS (NO. 6 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 6 CAN junction connector.

C358915C01
5.125,0.052 5.521,0.323 0.396,0.271 1.563,0.094 1.958,0.365 0.396,0.271 1.875,0.76 2.198,0.417 2.198,0.417 2.365,0.417 true 2.063,0.865 2.417,0.625 2.417,0.625 2.573,0.625 true 2.292,1.458 2.135,1.458 2.135,1.458 1.885,1.042 true 1.146,0.438 1.292,0.438 1.292,0.438 1.656,0.823 true 0.958,0.656 1.115,0.656 1.115,0.656 1.49,0.854 true 0.969,1.427 1.115,1.417 1.115,1.417 1.51,1.052 true 6.385,1.49 6.24,1.49 6.24,1.49 5.896,1.094 true 4.802,1.5 4.969,1.5 4.969,1.5 5.302,0.813 true 1.615,0.156 2.073,0.354 0.458,0.198 10 false A122 5.219,0.125 5.677,0.323 0.458,0.198 10 false J45 6.438,1.406 6.75,1.604 0.313,0.198 10 false BAT 0.458,0.094 0.771,0.292 0.313,0.198 10 false *a 4.042,0.115 4.354,0.313 0.313,0.198 10 false *b 0.615,0.375 1.531,0.573 0.917,0.198 10 false CANH*d 0.406,0.583 1.323,0.781 0.917,0.198 10 false CANH*c 0.406,1.375 1.323,1.573 0.917,0.198 10 false CANH*e 2.365,1.396 3.281,1.594 0.917,0.198 10 false CANL*e 2.646,0.573 3.563,0.771 0.917,0.198 10 false CANL*d 2.427,0.354 3.344,0.552 0.917,0.198 10 false CANL*c 4.563,1.417 4.875,1.615 0.313,0.198 10 false CG
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b Front view of DLC3
*c to No. 2 CAN Junction Connector *d to No. 5 CAN Junction Connector
*e to No. 2 Nitrogen Oxides Sensor - -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
A122-1 (CANH) - A122-3 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 2 CAN junction connector
A122-1 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A122-3 (CANL) - J45-16 (BAT)
A122-1 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A122-3 (CANL) - J45-4 (CG)
A122-2 (CANH) - A122-4 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 5 CAN junction connector
A122-2 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A122-4 (CANL) - J45-16 (BAT)
A122-2 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A122-4 (CANL) - J45-4 (CG)
A122-5 (CANH) - A122-7 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 2 nitrogen oxides sensor
A122-5 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A122-7 (CANL) - J45-16 (BAT)
A122-5 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A122-7 (CANL) - J45-4 (CG)



d.

Reconnect the No. 6 CAN junction connector.


Result:
Result Proceed to
OK A
NG (No. 2 CAN junction connector main wire) B
NG (No. 5 CAN junction connector main wire) C
NG (No. 2 nitrogen oxides sensor branch wire) D



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

3.CHECK CAN BUS (NO. 2 CAN JUNCTION CONNECTOR)

C

10.CHECK CAN BUS (NO. 5 CAN JUNCTION CONNECTOR)

D

16.CHECK CAN BUS (NO. 2 NITROGEN OXIDES SENSOR - NO. 6 CAN JUNCTION CONNECTOR)
3.CHECK CAN BUS (NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 2 CAN junction connector.

C358915C06
5.125,0.052 5.521,0.323 0.396,0.271 1.563,0.094 1.958,0.365 0.396,0.271 1.875,0.76 2.198,0.417 2.198,0.417 2.365,0.417 true 2.063,0.865 2.417,0.625 2.417,0.625 2.573,0.625 true 5.885,1.51 5.74,1.51 5.74,1.51 5.292,0.813 true 2.271,1.615 2.115,1.615 2.115,1.615 1.844,1.042 true 1.146,0.438 1.292,0.438 1.292,0.438 1.656,0.823 true 0.958,0.656 1.115,0.656 1.115,0.656 1.49,0.854 true 1,1.333 1.167,1.333 1.167,1.333 1.51,1.052 true 1.167,1.573 1.333,1.573 1.333,1.573 1.698,1.042 true 2.635,1.375 2.479,1.375 2.479,1.375 2.021,0.99 true 6.396,0.823 6.25,0.823 6.25,0.823 5.906,1.052 true 1.625,0.156 2.083,0.354 0.458,0.198 10 false A121 5.219,0.125 5.677,0.323 0.458,0.198 10 false J45 5.958,1.448 6.271,1.646 0.313,0.198 10 false CG 0.458,0.094 0.771,0.292 0.313,0.198 10 false *a 4.042,0.115 4.354,0.313 0.313,0.198 10 false *b 0.615,0.375 1.531,0.573 0.917,0.198 10 false CANH*d 0.406,0.583 1.323,0.781 0.917,0.198 10 false CANH*c 0.438,1.25 1.354,1.448 0.917,0.198 10 false CANH*e 2.344,1.542 3.26,1.74 0.917,0.198 10 false CANL*f 2.646,0.573 3.563,0.771 0.917,0.198 10 false CANL*c 2.427,0.354 3.344,0.552 0.917,0.198 10 false CANL*d 0.646,1.51 1.563,1.708 0.917,0.198 10 false CANH*f 2.708,1.281 3.625,1.479 0.917,0.198 10 false CANL*e 6.448,0.76 6.823,0.99 0.375,0.229 10 false BAT
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b Front view of DLC3
*c to No. 6 CAN Junction Connector *d to No. 10 CAN Junction Connector
*e to Particulate Matter Sensor *f to No. 1 Nitrogen Oxides Sensor



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
A121-1 (CANH) - A121-4 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 6 CAN junction connector
A121-1 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A121-4 (CANL) - J45-16 (BAT)
A121-1 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A121-4 (CANL) - J45-4 (CG)
A121-2 (CANH) - A121-3 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 10 CAN junction connector
A121-2 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A121-3 (CANL) - J45-16 (BAT)
A121-2 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A121-3 (CANL) - J45-4 (CG)
A121-5 (CANH) - A121-8 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Particulate matter sensor
A121-5 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A121-8 (CANL) - J45-16 (BAT)
A121-5 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A121-8 (CANL) - J45-4 (CG)
A121-6 (CANH) - A121-7 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 1 nitrogen oxides sensor
A121-6 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A121-7 (CANL) - J45-16 (BAT)
A121-6 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A121-7 (CANL) - J45-4 (CG)



c.

Reconnect the No. 2 CAN junction connector.


Result:
Result Proceed to
OK A
NG (No. 10 CAN junction connector main wire) B
NG (No. 6 CAN junction connector main wire) C
NG (No. 1 nitrogen oxides sensor branch wire) D
NG (Particulate matter sensor branch wire) E



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

4.CHECK CAN BUS (NO. 10 CAN JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 6 CAN JUNCTION CONNECTOR)

D

8.CHECK CAN BUS (NO. 1 NITROGEN OXIDES SENSOR - NO. 2 CAN JUNCTION CONNECTOR)

E

9.CHECK CAN BUS (PARTICULATE MATTER SENSOR - NO. 2 CAN JUNCTION CONNECTOR)
4.CHECK CAN BUS (NO. 10 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 10 CAN junction connector.

C358915C07
5.125,0.052 5.521,0.323 0.396,0.271 1.563,0.094 1.958,0.365 0.396,0.271 1.875,0.76 2.198,0.417 2.198,0.417 2.365,0.417 true 2.063,0.865 2.417,0.625 2.417,0.625 2.573,0.625 true 5.885,1.51 5.74,1.51 5.74,1.51 5.292,0.813 true 2.271,1.615 2.115,1.615 2.115,1.615 1.844,1.042 true 1.146,0.438 1.292,0.438 1.292,0.438 1.656,0.823 true 0.958,0.656 1.115,0.656 1.115,0.656 1.49,0.854 true 1,1.333 1.167,1.333 1.167,1.333 1.51,1.052 true 1.167,1.573 1.333,1.573 1.333,1.573 1.698,1.042 true 2.635,1.375 2.479,1.375 2.479,1.375 2.021,0.99 true 6.406,0.885 6.26,0.885 6.26,0.885 5.938,1.063 true 1.656,0.156 2.115,0.354 0.458,0.198 10 false P17 5.219,0.125 5.677,0.323 0.458,0.198 10 false J45 5.958,1.448 6.271,1.646 0.313,0.198 10 false CG 0.458,0.094 0.771,0.292 0.313,0.198 10 false *a 4.042,0.115 4.354,0.313 0.313,0.198 10 false *b 0.615,0.375 1.531,0.573 0.917,0.198 10 false CANH*d 0.406,0.583 1.323,0.781 0.917,0.198 10 false CANH*c 0.438,1.25 1.354,1.448 0.917,0.198 10 false CANH*e 2.344,1.542 3.26,1.74 0.917,0.198 10 false CANL*e 2.646,0.573 3.563,0.771 0.917,0.198 10 false CANL*d 2.427,0.354 3.344,0.552 0.917,0.198 10 false CANL*c 0.646,1.51 1.563,1.708 0.917,0.198 10 false CANH*f 2.708,1.281 3.625,1.479 0.917,0.198 10 false CANL*f 6.448,0.823 6.854,1.083 0.406,0.26 10 false BAT
*a Front view of wire harness connector
(to No. 10 CAN Junction Connector)
*b Front view of DLC3
*c to Emission Control ECU Assembly *d to No. 4 CAN Junction Terminal
*e to No. 2 CAN Junction Connector *f to Urea Sensor Assembly



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
P17-1 (CANH) - P17-3 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Emission control ECU assembly
P17-1 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
P17-3 (CANL) - J45-16 (BAT)
P17-1 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
P17-3 (CANL) - J45-4 (CG)
P17-2 (CANH) - P17-4 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 4 CAN junction terminal
P17-2 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
P17-4 (CANL) - J45-16 (BAT)
P17-2 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
P17-4 (CANL) - J45-4 (CG)
P17-5 (CANH) - P17-7 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 2 CAN junction connector
P17-5 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
P17-7 (CANL) - J45-16 (BAT)
P17-5 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
P17-7 (CANL) - J45-4 (CG)
P17-6 (CANH) - P17-8 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Urea sensor assembly
P17-6 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
P17-8 (CANL) - J45-16 (BAT)
P17-6 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
P17-8 (CANL) - J45-4 (CG)



c.

Reconnect the No. 10 CAN junction connector.


Result:
Result Proceed to
OK A
NG (No. 4 CAN junction terminal main wire) B
NG (Emission control ECU assembly branch wire) C
NG (Urea sensor assembly branch wire) D
NG (No. 2 CAN junction connector main wire) E



A

REPLACE NO. 10 CAN JUNCTION CONNECTOR

B

5.CHECK CAN BUS (NO. 4 CAN JUNCTION TERMINAL - NO. 10 CAN JUNCTION CONNECTOR)

C

6.CHECK CAN BUS (EMISSION CONTROL ECU ASSEMBLY - NO. 10 CAN JUNCTION CONNECTOR)

D

7.CHECK CAN BUS (UREA SENSOR ASSEMBLY - NO. 10 CAN JUNCTION CONNECTOR)

E

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (NO. 10 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

5.CHECK CAN BUS (NO. 4 CAN JUNCTION TERMINAL - NO. 10 CAN JUNCTION CONNECTOR)
a.
C251147C18
2.438,0.708 2.854,0.969 0.417,0.26 0.469,2.51 0.885,2.771 0.417,0.26 1.052,1.188 1.198,1.188 1.198,1.188 1.396,0.906 true 1.333,0.313 1.479,0.313 1.479,0.313 1.677,0.729 true 2.438,3.083 2.323,3.083 2.323,3.083 2.198,2.844 true 1.302,2.104 1.479,2.104 1.479,2.104 1.667,2.438 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 0.094,1.969 0.406,2.125 0.313,0.156 10 false *b 0.927,0.25 1.448,0.427 0.521,0.177 10 false VGND 0.594,1.125 1.042,1.375 0.448,0.25 10 false VOUT 2.5,0.771 2.948,1.021 0.448,0.25 10 false A118 0.531,2.563 0.979,2.813 0.448,0.25 10 false J45 1.052,2.031 1.5,2.281 0.448,0.25 10 false CG 2.479,3.01 2.927,3.26 0.448,0.25 10 false BAT
*a Rear view of wire harness connector
(to No. 4 CAN Junction Terminal)
*b Front view of DLC3


Disconnect the No. 4 CAN junction terminal connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A118-3 (VOUT) - A118-2 (VGND) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A118-3 (VOUT) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A118-2 (VGND) - J45-16 (BAT)
A118-3 (VOUT) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A118-2 (VGND) - J45-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 CAN JUNCTION TERMINAL

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (NO. 4 CAN JUNCTION TERMINAL - NO. 10 CAN JUNCTION CONNECTOR)

6.CHECK CAN BUS (EMISSION CONTROL ECU ASSEMBLY - NO. 10 CAN JUNCTION CONNECTOR)
SST
09843-E7020  

a.
C421149C03
1.542,0.375 1.927,0.594 0.385,0.219 0.583,1.333 0.583,0.667 0.583,0.667 0.833,0.667 true 2.844,1.094 2.677,0.448 2.677,0.448 2.927,0.448 true 2.792,1.594 2.51,2.281 2.51,2.281 2.76,2.281 true 2.385,1.75 2.083,2.333 2.083,2.333 1.917,2.333 true 1.688,0.417 1.844,0.615 0.156,0.198 10 false E 0.104,0.104 0.385,0.302 0.281,0.198 10 false *a 0.875,0.594 1.302,0.802 0.427,0.208 10 false CA2H 2.969,0.375 3.396,0.583 0.427,0.208 10 false CA2L 2.823,2.208 3.25,2.417 0.427,0.208 10 false BATT 1.635,2.25 2.063,2.458 0.427,0.208 10 false E01
*a Signal Check Harness Connector


Connect the signal check harness to the emission control ECU assembly vehicle side harness.

NOTICE:

Connect the signal check harness to prevent damage to the connector and improve work efficiency when performing the check.


HINT:

Refer to the following table for the ECU connector terminals and their corresponding signal check connector terminals.

ECU Connector Terminal Signal Check Harness Connector Terminal
P12-11 (CA2H) E11 (CA2H)
P12-10 (CA2L) E10 (CA2L)
P12-30 (BATT) E30 (BATT)
P12-38 (E01) E38 (E01)



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E11 (CA2H) - E10 (CA2L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E11 (CA2H) - E30 (BATT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E10 (CA2L) - E30 (BATT)
E11 (CA2H) - E38 (E01) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E10 (CA2L) - E38 (E01)



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (EMISSION CONTROL ECU ASSEMBLY - NO. 10 CAN JUNCTION CONNECTOR)

7.CHECK CAN BUS (UREA SENSOR ASSEMBLY - NO. 10 CAN JUNCTION CONNECTOR)
a.
C422459C01
1.427,0.25 1.802,0.552 0.375,0.302 1.438,2.573 1.813,2.875 0.375,0.302 2.771,4.385 2.521,4.385 2.521,4.385 2.25,3.677 true 2.677,2.208 2.427,2.208 2.427,2.208 2.313,1.604 true 1.854,2.323 2.021,2.323 2.021,2.323 2.115,1.594 true 1.104,2.875 1.271,2.875 1.271,2.875 1.594,3.26 true 0.333,0.354 0.646,0.552 0.313,0.198 10 false *a 0.313,2.719 0.625,2.917 0.313,0.198 10 false *b 1.479,0.333 1.792,0.531 0.313,0.198 10 false P13 1.51,2.625 1.823,2.823 0.313,0.198 10 false J45 2.813,4.313 3.125,4.51 0.313,0.198 10 false BAT 2.74,2.135 3.24,2.344 0.5,0.208 10 false CANH 1.469,2.26 1.969,2.469 0.5,0.208 10 false CANL 0.833,2.802 1.333,3.01 0.5,0.208 10 false CG
*a Front view of wire harness connector
(to Urea Sensor Assembly)
*b Front view of DLC3


Disconnect the urea sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P13-4 (CANH) - P13-5 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
P13-4 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
P13-5 (CANL) - J45-16 (BAT)
P13-4 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
P13-5 (CANL) - J45-4 (CG)



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (UREA SENSOR ASSEMBLY - NO. 10 CAN JUNCTION CONNECTOR)

8.CHECK CAN BUS (NO. 1 NITROGEN OXIDES SENSOR - NO. 2 CAN JUNCTION CONNECTOR)
a.
C422460C01
0.365,0.927 0.792,1.188 0.427,0.26 0.354,2.469 0.781,2.729 0.427,0.26 2.667,3.083 2.5,3.083 2.5,3.083 2.323,2.792 true 2.104,1.99 1.938,1.99 1.938,1.99 1.688,2.375 true 2.188,1.667 2.021,1.667 2.021,1.667 1.792,1.146 true 1.281,1.635 1.448,1.635 1.448,1.635 1.563,1.156 true 0.49,0.281 0.802,0.479 0.313,0.198 10 false *a 0.521,1.917 0.833,2.115 0.313,0.198 10 false *b 0.406,0.948 0.781,1.146 0.375,0.198 10 false A116 0.438,2.521 0.813,2.719 0.375,0.198 10 false J45 2.708,3.01 3.083,3.208 0.375,0.198 10 false BAT 2.156,1.927 2.531,2.125 0.375,0.198 10 false CG 2.25,1.573 2.688,1.771 0.438,0.198 10 false CANL 0.854,1.563 1.375,1.771 0.521,0.208 10 false CANH
*a Front view of wire harness connector
(to No. 1 Nitrogen Oxides Sensor)
*b Front view of DLC3


Disconnect the No. 1 nitrogen oxides sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A116-2 (CANH) - A116-3 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A116-2 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A116-3 (CANL) - J45-16 (BAT)
A116-2 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A116-3 (CANL) - J45-4 (CG)



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (NO. 1 NITROGEN OXIDES SENSOR - NO. 2 CAN JUNCTION CONNECTOR)

9.CHECK CAN BUS (PARTICULATE MATTER SENSOR - NO. 2 CAN JUNCTION CONNECTOR)
a.
C422460C04
0.365,0.927 0.792,1.188 0.427,0.26 0.354,2.469 0.781,2.729 0.427,0.26 2.667,3.083 2.5,3.083 2.5,3.083 2.323,2.792 true 2.104,1.99 1.938,1.99 1.938,1.99 1.688,2.375 true 2.438,1.667 2.271,1.667 2.271,1.667 2.042,1.146 true 1.469,1.635 1.635,1.635 1.635,1.635 1.75,1.156 true 0.49,0.281 0.802,0.479 0.313,0.198 10 false *a 0.521,1.917 0.833,2.115 0.313,0.198 10 false *b 0.438,0.958 0.813,1.156 0.375,0.198 10 false P15 0.438,2.521 0.813,2.719 0.375,0.198 10 false J45 2.708,3.01 3.083,3.208 0.375,0.198 10 false BAT 2.156,1.927 2.531,2.125 0.375,0.198 10 false CG 2.479,1.583 2.917,1.781 0.438,0.198 10 false CANL 1.073,1.563 1.594,1.771 0.521,0.208 10 false CANH
*a Front view of wire harness connector
(to Particulate Matter Sensor)
*b Front view of DLC3


Disconnect the particulate matter sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P15-3 (CANH) - P15-4 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
P15-3 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
P15-4 (CANL) - J45-16 (BAT)
P15-3 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
P15-4 (CANL) - J45-4 (CG)



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (PARTICULATE MATTER SENSOR - NO. 2 CAN JUNCTION CONNECTOR)

10.CHECK CAN BUS (NO. 5 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 5 CAN junction terminal connector.

C358915C08
5.125,0.052 5.521,0.323 0.396,0.271 1.563,0.094 2.021,0.365 0.458,0.271 1.875,0.76 2.198,0.417 2.198,0.417 2.365,0.417 true 2.063,0.865 2.417,0.625 2.417,0.625 2.573,0.625 true 6.333,1.458 6.188,1.458 6.188,1.458 5.906,1.073 true 2.271,1.615 2.115,1.615 2.115,1.615 1.844,1.042 true 1.146,0.438 1.292,0.438 1.292,0.438 1.656,0.823 true 0.958,0.656 1.115,0.656 1.115,0.656 1.49,0.854 true 1,1.333 1.167,1.333 1.167,1.333 1.51,1.052 true 1.167,1.573 1.333,1.573 1.333,1.573 1.698,1.042 true 2.635,1.375 2.479,1.375 2.479,1.375 2.021,0.99 true 6.021,0.375 5.875,0.375 5.875,0.375 5.344,0.698 true 1.625,0.156 2.083,0.354 0.458,0.198 10 false B118 5.219,0.125 5.677,0.323 0.458,0.198 10 false J45 6.396,1.375 6.708,1.573 0.313,0.198 10 false BAT 0.458,0.094 0.771,0.292 0.313,0.198 10 false *a 4.042,0.115 4.354,0.313 0.313,0.198 10 false *b 0.615,0.375 1.531,0.573 0.917,0.198 10 false CANH*d 0.406,0.583 1.323,0.781 0.917,0.198 10 false CANH*c 0.438,1.25 1.354,1.448 0.917,0.198 10 false CANH*e 2.344,1.542 3.26,1.74 0.917,0.198 10 false CANL*e 2.646,0.573 3.563,0.771 0.917,0.198 10 false CANL*d 2.427,0.354 3.344,0.552 0.917,0.198 10 false CANL*c 0.646,1.51 1.563,1.708 0.917,0.198 10 false CANH*f 2.708,1.281 3.625,1.479 0.917,0.198 10 false CANL*f 6.063,0.292 6.375,0.49 0.313,0.198 10 false CG
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b Front view of DLC3
*c to EGR Valve Assembly *d to Turbocharger Sub-assembly
*e to No. 8 CAN Junction Connector *f to No. 6 CAN Junction Connector



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
B118-1 (CANH) - B118-3 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher EGR valve assembly
B118-1 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B118-3 (CANL) - J45-16 (BAT)
B118-1 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B118-3 (CANL) - J45-4 (CG)
B118-2 (CANH) - B118-4 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Turbocharger sub-assembly
B118-2 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B118-4 (CANL) - J45-16 (BAT)
B118-2 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B118-4 (CANL) - J45-4 (CG)
B118-5 (CANH) - B118-7 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 8 CAN junction connector
B118-5 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B118-7 (CANL) - J45-16 (BAT)
B118-5 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B118-7 (CANL) - J45-4 (CG)
B118-6 (CANH) - B118-8 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 6 CAN junction connector
B118-6 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B118-8 (CANL) - J45-16 (BAT)
B118-6 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B118-8 (CANL) - J45-4 (CG)



c.

Reconnect the No. 5 CAN junction terminal connector.


Result:
Result Proceed to
OK A
NG (No. 8 CAN junction connector main wire) B
NG (Turbocharger sub-assembly branch wire) C
NG (EGR valve assembly branch wire) D
NG (No. 6 CAN junction connector main wire) E



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

11.CHECK CAN BUS (NO. 8 CAN JUNCTION CONNECTOR)

C

14.CHECK CAN BUS (TURBOCHARGER SUB-ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

D

15.CHECK CAN BUS (EGR VALVE ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

E

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - NO. 6 CAN JUNCTION CONNECTOR)

11.CHECK CAN BUS (NO. 8 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 8 CAN junction connector.

C358918C06
0.156,0.708 0.563,1.01 0.406,0.302 5.125,0.125 5.542,0.396 0.417,0.271 6.219,1.625 6.073,1.625 6.073,1.625 5.906,1.125 true 2.333,0.969 2.552,0.323 2.552,0.323 2.708,0.323 true 2.219,0.958 2.042,0.292 2.042,0.292 1.896,0.292 true 2.094,0.969 1.906,0.458 1.906,0.458 1.792,0.458 true 1.75,1.448 1.865,1.448 1.865,1.448 2.104,1.188 true 1.927,1.646 2.063,1.646 2.063,1.646 2.208,1.167 true 2.635,1.552 2.469,1.552 2.469,1.552 2.333,1.177 true 5.26,0.719 4.76,0.323 4.76,0.323 4.646,0.323 true 0.167,0.073 0.479,0.271 0.313,0.198 10 false *a 3.875,0.125 4.188,0.323 0.313,0.198 10 false *b 0.219,0.781 0.677,0.979 0.458,0.198 10 false B149 6.292,1.563 6.75,1.76 0.458,0.198 10 false BAT 5.229,0.188 5.688,0.385 0.458,0.198 10 false J45 1.333,0.208 2.25,0.406 0.917,0.198 10 false CANH*d 1.229,0.375 2.146,0.573 0.917,0.198 10 false CANH*c 2.75,0.25 3.667,0.448 0.917,0.198 10 false CANH*e 2.688,1.479 3.604,1.677 0.917,0.198 10 false CANL*e 1.229,1.375 2.146,1.573 0.917,0.198 10 false CANL*c 1.406,1.563 2.323,1.76 0.917,0.198 10 false CANL*d 4.396,0.26 5.313,0.458 0.917,0.198 10 false CG
*a Front view of wire harness connector
(to No. 8 CAN Junction Connector)
*b Front view of DLC3
*c to ECM *d to No. 5 CAN Junction Connector
*e to No. 7 CAN Junction Terminal - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
B149-9 (CANH) - B149-20 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher ECM
B149-9 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B149-20 (CANL) - J45-16 (BAT)
B149-9 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B149-20 (CANL) - J45-4 (CG)
B149-10 (CANH) - B149-21 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 5 CAN junction connector
B149-10 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B149-21 (CANL) - J45-16 (BAT)
B149-10 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B149-21 (CANL) - J45-4 (CG)
B149-11 (CANH) - B149-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 7 CAN junction terminal
B149-11 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B149-22 (CANL) - J45-16 (BAT)
B149-11 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B149-22 (CANL) - J45-4 (CG)



c.

Reconnect the No. 8 CAN junction terminal connector.


Result:
Result Proceed to
OK A
NG (No. 7 CAN junction terminal main wire) B
NG (ECM branch wire) C
NG (No. 5 CAN junction connector main wire) D



A

REPLACE NO. 8 CAN JUNCTION CONNECTOR

B

12.CHECK CAN BUS (NO. 7 CAN JUNCTION TERMINAL - NO. 8 CAN JUNCTION CONNECTOR)

C

13.CHECK CAN BUS (ECM - NO. 8 CAN JUNCTION CONNECTOR)

D

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (NO. 8 CAN JUNCTION CONNECTOR - NO. 5 CAN JUNCTION CONNECTOR)

12.CHECK CAN BUS (NO. 7 CAN JUNCTION TERMINAL - NO. 8 CAN JUNCTION CONNECTOR)
a.
C251147C19
2.438,0.708 2.854,0.969 0.417,0.26 0.469,2.51 0.885,2.771 0.417,0.26 1.052,1.188 1.198,1.188 1.198,1.188 1.396,0.906 true 1.333,0.313 1.479,0.313 1.479,0.313 1.677,0.729 true 2.438,3.083 2.323,3.083 2.323,3.083 2.198,2.844 true 1.302,2.104 1.479,2.104 1.479,2.104 1.667,2.438 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 0.094,1.969 0.406,2.125 0.313,0.156 10 false *b 0.927,0.25 1.448,0.427 0.521,0.177 10 false VGND 0.594,1.125 1.042,1.375 0.448,0.25 10 false VOUT 2.5,0.771 2.948,1.021 0.448,0.25 10 false B145 0.531,2.563 0.979,2.813 0.448,0.25 10 false J45 1.052,2.031 1.5,2.281 0.448,0.25 10 false CG 2.479,3.01 2.927,3.26 0.448,0.25 10 false BAT
*a Rear view of wire harness connector
(to No. 7 CAN Junction Terminal)
*b Front view of DLC3


Disconnect the No. 7 CAN junction terminal connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B145-3 (VOUT) - B145-2 (VGND) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
B145-3 (VOUT) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B145-2 (VGND) - J45-16 (BAT)
B145-3 (VOUT) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B145-2 (VGND) - J45-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE NO. 7 CAN JUNCTION TERMINAL

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (NO. 7 CAN JUNCTION TERMINAL - NO. 8 CAN JUNCTION CONNECTOR)

13.CHECK CAN BUS (ECM - NO. 8 CAN JUNCTION CONNECTOR)
SST
09843-E7010  

a.

Connect the signal check harness to the ECM vehicle side harness.

C379569C05
2.115,0.063 2.469,0.281 0.354,0.219 4.583,0.063 4.938,0.281 0.354,0.219 3.031,0.698 2.833,0.167 2.833,0.167 3,0.167 true 3.052,1.063 3.01,1.448 3.01,1.448 3.177,1.448 true 3.844,0.542 4.021,0.156 4.021,0.156 4.188,0.156 true 4.01,0.729 4.5,1.375 4.5,1.375 4.667,1.375 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 2.281,0.104 2.885,0.333 0.604,0.229 10 false E 4.708,0.104 5.313,0.333 0.604,0.229 10 false V 4.24,0.073 4.729,0.344 0.49,0.271 10 false +B 3.229,1.375 3.719,1.646 0.49,0.271 10 false CAN- 3.052,0.083 3.542,0.354 0.49,0.271 10 false CAN+ 4.719,1.302 5.208,1.573 0.49,0.271 10 false E01
*a Signal Check Harness Connector - -


NOTICE:

Connect the signal check wiring harness to prevent damage to the connector and improve work efficiency when performing the check.


HINT:

Refer to the following table for the ECU connector terminals and their corresponding signal check connector terminals.

ECU Connector Terminal Signal Check Harness Connector Terminal
B142-80 (CAN+) E59 (CAN+)
B142-102 (CAN-) E79 (CAN-)
A115-49 (+B) V1 (+B)
A115-12 (E01) V40 (E01)



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E59 (CAN+) - E79 (CAN-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E59 (CAN+) - V1 (+B) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E79 (CAN-) - V1 (+B)
E59 (CAN+) - V40 (E01) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E79 (CAN-) - V40 (E01)



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (ECM - NO. 8 CAN JUNCTION CONNECTOR)

14.CHECK CAN BUS (TURBOCHARGER SUB-ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)
a.
C422461C01
0.354,0.865 0.615,1.115 0.26,0.25 0.313,2.271 0.656,2.521 0.344,0.25 2.25,2.583 2.417,3 2.417,3 2.667,3 true 1.833,1.125 2.073,1.75 2.073,1.75 2.323,1.75 true 2.042,1.094 2.469,1.531 2.469,1.531 2.719,1.531 true 1.635,2.198 1.375,1.667 1.375,1.667 1.208,1.667 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 0.396,0.917 0.708,1.115 0.313,0.198 10 false j5 0.385,2.333 0.698,2.531 0.313,0.198 10 false J45 0.073,1.677 0.385,1.875 0.313,0.198 10 false *b 2.719,2.927 3.031,3.125 0.313,0.198 10 false BAT 2.365,1.667 2.885,1.896 0.521,0.229 10 false CANL 2.771,1.448 3.292,1.677 0.521,0.229 10 false CANH 0.979,1.594 1.5,1.823 0.521,0.229 10 false CG
*a Front view of wire harness connector
(to Turbocharger Sub-assembly)
*b Front view of DLC3


Disconnect the turbocharger sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j5-4 (CANH) - j5-3 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
j5-4 (CANH) - - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
j5-3 (CANL) - - J45-16 (BAT)
j5-4 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
j5-3 (CANL) - J45-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE TURBOCHARGER SUB-ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (TURBOCHARGER SUB-ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

15.CHECK CAN BUS (EGR VALVE ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)
a.
C422475C01
0.354,0.865 0.792,1.115 0.438,0.25 0.313,2.271 0.656,2.521 0.344,0.25 2.25,2.583 2.417,3 2.417,3 2.667,3 true 1.76,1.156 2,1.781 2,1.781 2.25,1.781 true 1.74,0.979 2,0.365 2,0.365 2.25,0.365 true 1.625,2.302 1.281,1.698 1.281,1.698 1.115,1.698 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 0.427,0.917 0.833,1.135 0.406,0.219 10 false B48 0.385,2.333 0.698,2.531 0.313,0.198 10 false J45 0.073,1.677 0.385,1.875 0.313,0.198 10 false *b 2.719,2.927 3.031,3.125 0.313,0.198 10 false BAT 2.333,0.292 2.854,0.521 0.521,0.229 10 false CANL 2.313,1.708 2.833,1.938 0.521,0.229 10 false CANH 0.823,1.635 1.344,1.865 0.521,0.229 10 false CG
*a Front view of wire harness connector
(to EGR Valve Assembly)
*b Front view of DLC3


Disconnect the EGR valve assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B48-5 (CANH) - B48-2 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
B48-5 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B48-2 (CANL) - J45-16 (BAT)
B48-5 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B48-2 (CANL) - J45-4 (CG)



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (EGR VALVE ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

16.CHECK CAN BUS (NO. 2 NITROGEN OXIDES SENSOR - NO. 6 CAN JUNCTION CONNECTOR)
a.
C422460C02
0.365,0.927 0.792,1.188 0.427,0.26 0.354,2.469 0.781,2.729 0.427,0.26 2.667,3.083 2.5,3.083 2.5,3.083 2.323,2.792 true 2.104,1.99 1.938,1.99 1.938,1.99 1.688,2.375 true 2.188,1.667 2.021,1.667 2.021,1.667 1.792,1.146 true 1.281,1.635 1.448,1.635 1.448,1.635 1.563,1.156 true 0.49,0.281 0.802,0.479 0.313,0.198 10 false *a 0.521,1.917 0.833,2.115 0.313,0.198 10 false *b 0.448,0.958 0.823,1.156 0.375,0.198 10 false P14 0.438,2.521 0.813,2.719 0.375,0.198 10 false J45 2.708,3.01 3.083,3.208 0.375,0.198 10 false BAT 2.156,1.927 2.531,2.125 0.375,0.198 10 false CG 2.25,1.573 2.688,1.771 0.438,0.198 10 false CANL 0.854,1.563 1.375,1.771 0.521,0.208 10 false CANH
*a Front view of wire harness connector
(to No. 2 Nitrogen Oxides Sensor)
*b Front view of DLC3


Disconnect the No. 2 nitrogen oxides sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P14-2 (CANH) - P14-3 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
P14-2 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
P14-3 (CANL) - J45-16 (BAT)
P14-2 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
P14-3 (CANL) - J45-4 (CG)



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (NO. 2 NITROGEN OXIDES SENSOR - NO. 6 CAN JUNCTION CONNECTOR)