Home › Engine / Hybrid System › N04C-UH (FUEL) › FUEL INJECTOR › 2019.08–2021.01
RM2850E _51 Engine / Hybrid System _073175 N04C-UH FUEL _0356078 FUEL INJECTOR A

N04C-UH FUEL  FUEL INJECTOR  REMOVAL  


PROCEDURE

Hide 1.CHECK FOR INJECTOR COMPENSATION CODE

a.

Check that the injection compensation code registered in the injector assembly installed on each cylinder match the ones registered in the ECM.

Click hereEngine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION


b.

If they do not match, follow the procedures below to correct the registration details and recheck the symptom.

i.

Correct the registration details by following the procedures in "register injection compensation code".

Click hereEngine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION


ii.

After correcting the registration details, check if the same symptom occurs as when the vehicle was brought in.

HINT:

If it does not occur, the symptom may be caused by errors in injection compensation code registration.




Hide 58521D 2.REMOVE ENGINE SERVICE HOLE COVER MAT (w/ Carpet)

Hide 58410 3.REMOVE ENGINE SERVICE HOLE COVER

Hide 58734B 4.REMOVE ENGINE SERVICE COVER WEATHERSTRIP REAR

Hide 58521D 5.REMOVE ENGINE SERVICE HOLE COVER MAT (w/o Carpet)

Hide 58420 6.REMOVE NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY

Hide 58534A 7.REMOVE TRANSMISSION COVER MAT (for Manual Transmission)

Hide 33531B 8.REMOVE SHIFT AND SELECT LEVER SHAFT DUST BOOT (for LHD)

Hide 58848A 9.REMOVE SHIFT LEVER HOLE COVER WITH BOOTS (for RHD)

Hide 33820B 10.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for LHD)

Hide 33820B 11.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for RHD)

Hide 33504F 12.REMOVE SHIFT LEVER SUB-ASSEMBLY (for Manual Transmission)

Hide 58841A 13.REMOVE SHIFTING HOLE COVER (for Automatic Transmission)

Hide 33820B 14.REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transmission)

Hide 33503F 15.REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY (for Automatic Transmission)

Hide 58701A 16.REMOVE FRONT ENGINE SERVICE COVER PANEL SUB-ASSEMBLY (for LHD)

Hide 58701A 17.REMOVE FRONT ENGINE SERVICE COVER PANEL SUB-ASSEMBLY (for RHD)

Hide 16206C 19.SEPARATE WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 17113 20.REMOVE INTAKE PIPE

Hide 17271 21.REMOVE NO. 1 TURBO INSULATOR

Hide 25608 22.REMOVE EGR COOLER SUB-ASSEMBLY

Hide 12180E 23.REMOVE OIL FILLER CAP SUB-ASSEMBLY

a.
A146428

Remove the oil filler cap.


Hide 11202D 24.REMOVE NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A157042

Remove the 2 bolts, the 2 stays and the No. 2 cylinder head cover.


Hide 11201 25.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A157041

Disconnect the 5 connectors and remove the wire harness.


b.

Remove the cylinder head cover cushion rubber.


c.

Remove the 2 bolts, the 2 cushions, and the cylinder head cover.


d.

Remove the gasket from the cylinder head cover.


Hide 23741B 26.REMOVE INJECTION PIPE CLAMP

a.
A157024

Remove the 2 nuts and the 2 injection pipe clamps.


Hide 23670 27.REMOVE INJECTOR ASSEMBLY

a.
A146738

Using a union nut wrench (17 mm), loosen the union nuts and disconnect the No. 1, No. 2, No. 3 and No. 4 injection pipes.


b.
A146733

Using a small screwdriver, move the 4 holder seals.


c.
A146732

Remove the union bolt, 4 hollow screws, 5 gaskets and nozzle leakage pipe.

NOTICE:

After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector.



d.
A146734

Remove the 4 bolts and 4 nozzle holder clamps.

NOTICE:

Arrange the holder clamps and bolts in the correct order.



e.

Remove the 4 injectors.

NOTICE:

Arrange the injectors in the correct order.



f.

Remove the No. 2 cylinder head cover gasket from each injector.


g.
A101564

Engage tags to identify the cylinder (#1 to #4) to the injector assemblies so that each injector assembly can be inserted into the correct cylinder during installation.


h.
A430792E01
1.313,0.906 1.396,1.219 false 1.198,0.729 1.51,0.927 0.313,0.198 10 false *1

Remove the O-ring from each injector.

Text in Illustration
*1 O-ring

i.

Remove the 4 injection nozzle seats from the cylinder head.