Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0562  System Voltage Low  P0563  System Voltage High  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0562 System Voltage Low Diagnosis Condition:

Engine speed 500 rpm or more.


Malfunction Status:

ECM power supply voltage 10 V or less.


Malfunction Duration:

3 seconds or more


·

Fuse

·

Harness or connector

·

Battery

·

Generator

·

ECM


Class B1 DTC stored
P0563 System Voltage High Diagnosis Condition:

Engine speed 500 rpm or more.


Malfunction Status:

ECM power supply voltage 16 V or more.


Malfunction Duration:

3 seconds or more


·

Fuse

·

Harness or connector

·

Battery

·

Generator

·

ECM


Class B1 DTC stored

MONITOR DESCRIPTION

Excessively low or high voltage has been detected in the ECU power supply.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0562
P0563
Idle the engine for 3 seconds or more.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT FUSE
a.

Check the fuse connection condition (defective or loose connection ).

Standard:

The fuse is installed correctly



Result:
Proceed to
OK
NG



OK

2.INSPECT BATTERY TERMINAL

NG

11.CONNECT SECURELY
2.INSPECT BATTERY TERMINAL
a.

Check the connection condition of the battery terminal and generator terminal (defective or loose connection).

Standard:

The battery terminal and generator terminal are installed correctly



Result:
Proceed to
OK
NG



OK

3.INSPECT GENERATOR

NG

10.CONNECT SECURELY
3.INSPECT GENERATOR
a.

Start the engine.


b.

Check the voltage of the generator terminal B during idling.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Generator terminal B - Body ground Idling 12 V or more



Result:
Proceed to
OK
NG



OK

4.INSPECT ECM (+B1,+B2, +B3 VOLTAGE)

NG

9.REPAIR OR REPLACE GENERATOR
4.INSPECT ECM (+B1,+B2, +B3 VOLTAGE)
a.
A405886C14
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


A405887C21
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false V
*a Signal Check Harness Lead Connector


Turn the ignition switch off.


b.

Connect the signal check harness to the ECM vehicle side harness.


c.

Start the engine.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
V-18 - V-40 Idling 11 to 14 V
V-38 - V-40 Idling 11 to 14 V
V-58 - V-40 Idling 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK DTC OUTPUT

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM POWER SUPPLY CIRCUIT)
5.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P0562 or P0563 is output A
DTCs are not output B




A

6.REPLACE ECM

B

END

6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

8.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM POWER SUPPLY CIRCUIT)
a.

Repair or replace the ECM power source circuit harness.


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
9.REPAIR OR REPLACE GENERATOR
a.

Repair or replace the generator.


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
10.CONNECT SECURELY
a.

Securely connect the battery terminal and generator terminal.


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
11.CONNECT SECURELY
a.

Securely install the fuse.

HINT:

Replace if necessary.



Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT