Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM J

N04C-VJ ENGINE CONTROL  ECD SYSTEM  Abnormal Temperature Detection by Exhaust Temperature Sensor (Upstream)  


CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

If the exhaust temperature sensor detects an abnormally high temperature, conduct the following inspection.

·

Check the amount of engine oil after troubleshooting is finished.

·

If the amount of engine oil is more than the specified level, replace the engine oil.



PROCEDURE

1.CHECK OTHER DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs.


Result:
Result Proceed to
DTC P2428, P244A, P244B, P244D, P2458, P2463 or P24A2 is output A
DTC P2428, P244A, P244B, P244D, P2458, P2463 or P24A2 and other DTCs are output B



A

2.CLEAR DTC

B

2.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clearing the DTCs turns off the message in the multi-information display.


Result:
Proceed to
NEXT




NEXT

3.CHECK FUEL SYSTEM
3.CHECK FUEL SYSTEM
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.


e.

Perform the Active Test with the engine idling.

Standard:
Item Condition Reference Value
Test the Fuel Leak With the engine speed at 2000 rpm in the Active Test, the fuel pressure in the common rail is set to (maintained at) 200000 kPa.
NOTICE:

Engine speed cannot be set by operating the accelerator pedal.


2000 rpm
(Fuel pressure 200000 kPa)
HINT:

If performed when cold, combustion may be unstable, but this is not a malfunction. Only check that the pressure increases to the target and that there is no fuel leak.




HINT:

Repair or replace if there is a malfunction.



f.

Check the fuel filter assembly for dirt or clogging.

HINT:

Repair or replace if there is a malfunction.



g.

After resolving the malfunction, proceed to the next step.


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR ENGINE OIL LEAK
4.CHECK FOR ENGINE OIL LEAK
a.

Check that the intake system pipes and hoses are not excessively contaminated with oil.

HINT:
·

If the pipes or hoses are contaminated with oil, clean them.

·

If pipes or hoses are contaminated with a large amount of oil, repair or replace the parts and areas where the engine oil is leaking from.




b.

Check if the engine oil is leaking from the turbocharger.


Result:
Proceed to
NEXT



NEXT

5.READ VALUE USING GTS (DIFFERENTIAL PRESSURE)
5.READ VALUE USING GTS (DIFFERENTIAL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.




f.

After the forcible regeneration is completed, allow the engine to idle for at least 5 minutes.


g.

Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.


h.

Check the differential pressure when the exhaust gas temperature sensor indicates 200°C or less.

HINT:
·

If the exhaust gas temperature is high, the differential pressure cannot be measured correctly.

·

If the differential pressure is outside the normal range, the center exhaust pipe assembly (catalytic converter) may have deteriorated or the center exhaust pipe assembly (catalytic converter) may be clogged with PM.

·

Fully depress the accelerator pedal and when the engine speed becomes stable, promptly read the differential pressure.




Result:
Engine Speed (no engine load) Differential Pressure Proceed to
3300 to 3400 rpm (Exhaust gas temperature (up stream) is 200°C or less) Less than 15 kPa (MIL is not illuminated) A
15 kPa or more (MIL is not illuminated) B
MIL remains ON C



A

END

B

REPLACE CENTER EXHAUST PIPE ASSEMBLY

C