Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM J

N04C-VJ ENGINE CONTROL  ECD SYSTEM  Clogging by DPF Catalytic Converter  


DESCRIPTION

The differential pressure sensor is mounted on the exhaust pipe. It measures the pressure before and after the DPF catalytic converter (monolithic converter assembly), converts the difference in pressure into a voltage signal, and outputs it to the ECM. Based on this signal, the ECM determines whether the DPF catalytic converter is clogged. If the DPF catalytic converter is clogged, the ECM activates the forcible regeneration function of the DPF catalytic converter. In some cases, the forcible regeneration function may not be conducted depending on the driving conditions. In such cases, the indicator light in the combination meter and the DPF switch light blink to inform the driver that the converter is clogged. When the driver presses the DPF switch, the forcible regeneration function signal (RGSW) is transmitted to the ECM, and the forcible regeneration function starts. If the vehicle is driven continuously without performing the forcible regeneration function when the indicator lights are blinking, PM (Particulate Matter) accumulates and DTC P2463 is set. If the forcible regeneration function is activated when the amount of PM accumulation is too high, the temperature in the DPF catalytic converter rises beyond normal operating conditions, (it may reach 800 °C (1472 °F) or higher), and the DPF catalytic converter may melt down. Therefore, if the forcible regeneration function is activated with DTC P2463 set, the differential pressure when the engine is running at near the maximum no-load speed (3550 rpm) must be checked. If the pressure exceeds the threshold, the DPF catalytic converter must be cleaned.

A160134E05
3.292,2.948 3.958,2.625 false 5.573,1.625 4.781,0.958 false 0.896,3.385 1.042,3.563 0.146,0.177 10 false 0 0.823,3.063 1.031,3.24 0.208,0.177 10 false 10 0.823,2.698 1.031,2.875 0.208,0.177 10 false 20 0.823,2.365 1.031,2.542 0.208,0.177 10 false 30 0.833,2.031 1.042,2.208 0.208,0.177 10 false 40 0.833,1.698 1.042,1.875 0.208,0.177 10 false 50 0.844,1.365 1.052,1.542 0.208,0.177 10 false 60 1.01,3.51 1.156,3.688 0.146,0.177 10 false 0 1.99,3.531 2.198,3.708 0.208,0.177 10 false 50 2.99,3.521 3.271,3.698 0.281,0.177 10 false 100 4.01,3.531 4.292,3.708 0.281,0.177 10 false 150 5.042,3.521 5.323,3.698 0.281,0.177 10 false 200 6.094,3.521 6.375,3.698 0.281,0.177 10 false 250 0.167,1.104 1.885,1.281 1.719,0.177 10 false Differential Pressure (kPa) 5.917,3.823 6.74,4 0.823,0.177 10 false MAF (gm/s) 4.052,2.521 6.208,2.698 2.156,0.177 10 false Differential Pressure Limit Value 4.104,0.844 4.823,1.021 0.719,0.177 10 false Threshold

Engine Speed Standard Differential Pressure MAF
3300 to 3400 rpm 15 kPa or less 135 to 145 gm/s

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the supply pump, the ECM needs initialization (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injector, the ECM needs registration (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



PROCEDURE

1.PERFORM ENGINE RPM ACCELERATION
a.

Warm up the engine.


b.

Disconnect the negative battery terminal and wait for at least 1 minute.


c.

Reconnect the negative battery terminal.


d.

Initialize the learning value of the supply pump (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

HINT:

Perform initialization with the engine warmed up (engine coolant temperature is 60°C (140°F) or more and fuel temperature is 20°C (68°F) or more).



e.

Initialize the learning value of the diesel throttle body (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


f.

Accelerate the engine speed to the maximum rpm with no load 20 times.


g.

Check the volume of black smoke in the exhaust gas.

HINT:

If DTC P2463 is stored, be sure to clear the DTCs.



Result:
Result Proceed to
Black smoke remains in the exhaust gas A
Black smoke is not present B



A

2.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

B

8.CLEAR DTC
2.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
a.

Inspect the air cleaner filter element sub-assembly.


Result:
Proceed to
OK
NG



OK

3.CHECK INTAKE SYSTEM

NG

REPAIR OR CLEAN AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

3.CHECK INTAKE SYSTEM
a.

Check for air leak from the intake system and check that the intake system is installed properly.


Result:
Proceed to
OK
NG



OK

4.INSPECT FUEL FILTER ASSEMBLY

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

4.INSPECT FUEL FILTER ASSEMBLY
a.

Inspect the fuel filter assembly.


Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (FUEL PRESS)

NG

REPLACE FUEL FILTER ASSEMBLY

5.READ VALUE USING GTS (FUEL PRESS)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.


e.

Check that the internal fuel pressure of the common rail is within the specification below.

Standard:
Engine Speed Fuel Press
Idling Approximately 20000 to 30000 kPa
2800 rpm Approximately 110000 to 120000 kPa


NOTICE:

The fuel pressure is listed here as a standard value, but the standard value will vary depending on the vehicle condition and model.

When judging the fuel pressure, check that the common rail target fuel pressure and fuel pressure follow reliably with the accelerator position and engine speed at a constant setting.

However, the common rail target fuel pressure and fuel pressure will not follow immediately after operating the accelerator pedal.


HINT:

If the actual fuel pressure differs from the target fuel pressure by +/-5000 kPa or more, there may be a fuel pressure malfunction.

When injection feedback value [QCY] is greater than 7 mm3/st or [QCY] is less than -7 mm3/st, there may be a faulty injector.



Result:
Proceed to
OK
NG



OK

6.CHECK FOR ENGINE OIL LEAK

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

6.CHECK FOR ENGINE OIL LEAK
a.

Check that the intake system pipes and hoses are not excessively contaminated with oil.


Result:
Proceed to
OK
NG



OK

7.CHECK CONNECTION OF VACUUM HOSE (DIFFERENTIAL PRESSURE SENSOR - CATALYTIC CONVERTER)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

7.CHECK CONNECTION OF VACUUM HOSE (DIFFERENTIAL PRESSURE SENSOR - CATALYTIC CONVERTER)
a.

Check if the vacuum hose routing between the differential pressure sensor and the center exhaust pipe assembly (catalytic converter) is correct.


b.

Check that there is no exhaust gas leak between the differential pressure sensor and the center exhaust pipe assembly (catalytic converter).


Result:
Proceed to
OK
NG



OK

8.CLEAR DTC

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

8.CLEAR DTC
a.

Warm up the engine.


b.

Disconnect the negative battery terminal and wait for at least 1 minute.


c.

Reconnect the negative battery terminal.


d.

Initialize the learning value of the supply pump (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

HINT:

Perform initialization with the engine warmed up (engine coolant temperature is 60°C (140°F) or more and fuel temperature is 20°C (68°F) or more).



e.

Initialize the learning value of the diesel throttle body (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


Result:
Proceed to
NEXT



NEXT

9.READ VALUE USING GTS (DIFFERENTIAL PRESSURE)
9.READ VALUE USING GTS (DIFFERENTIAL PRESSURE)
a.
A234890C05
0.385,0.792 0.802,1.042 0.417,0.25 10 false *a 1.615,0.24 2.01,0.521 0.396,0.281 10 false *c 0.406,1.333 0.74,1.594 0.333,0.26 10 false *b
*a Differential Pressure
*b Engine speed
*c Period to read differential pressure


Allow the engine to idle for at least 5 minutes.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.

HINT:
·

If the exhaust gas temperature is high, the differential pressure cannot be measured correctly.

·

If the differential pressure is outside the normal range, the center exhaust pipe assembly (catalytic converter) may have deteriorated or the center exhaust pipe assembly (catalytic converter) may be clogged with PM.

·

Fully depress the accelerator pedal and when the engine speed becomes stable, promptly read the differential pressure.




Result:
Engine Speed (no engine load) Differential Pressure Proceed to
3300 to 3400 rpm (Exhaust gas temperature (up stream) is 200°C or less) 25 kPa or more A
Less than 25 kPa B



A

10.READ VALUE USING GTS (EXHAUST TEMPERATURE DURING FORCIBLE REGENERATION FUNCTION)

B

16.CLEAN EXHAUST SYSTEM
10.READ VALUE USING GTS (EXHAUST TEMPERATURE DURING FORCIBLE REGENERATION FUNCTION)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Perform the forcible regeneration function (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>DPF Switch and Buzzer Circuit).


e.

Enter the following menus: Powertrain / Engine and ECT / Data List.


f.

Enter the following menus, and read the value every minute during the forcible regeneration function.

·

Exhaust Temperature B1S3

·

Exhaust Temperature B1S4

·

Engine Speed


Result:
Result Proceed to
[Exhaust Temperature B1S4] did not exceed 800°C (1472°F). A
[Exhaust Temperature B1S4] reached 800°C (1472°F) or more. B


NOTICE:

If Initial Exhaust Temperature B1S4 exceeds 800°C (1472°F), cease the forcible regeneration function immediately.




A

11.READ VALUE USING GTS (ENGINE SPEED DURING FORCIBLE REGENERATION FUNCTION)

B

16.CLEAN EXHAUST SYSTEM
11.READ VALUE USING GTS (ENGINE SPEED DURING FORCIBLE REGENERATION FUNCTION)
a.

Read the engine speed during the forcible regeneration function.

Standard:
Condition Engine Speed
During forcible regeneration function 1200 rpm or more



Result:
Proceed to
OK
NG



OK

12.READ VALUE USING GTS (EXHAUST TEMPERATURE DURING FORCIBLE REGENERATION FUNCTION)

NG

18.READ VALUE USING GTS (INJECTION VOLUME)
12.READ VALUE USING GTS (EXHAUST TEMPERATURE DURING FORCIBLE REGENERATION FUNCTION)
a.

Read the exhaust gas temperature B1S3 after at least 5 minutes have elapsed since the forcible regeneration function was started.

Standard:
Condition Exhaust Temperature B1S3
During forcible regeneration function 220°C (428°F) or more



Result:
Proceed to
OK
NG



OK

13.READ VALUE USING GTS (EXHAUST TEMPERATURE DURING FORCIBLE REGENERATION FUNCTION)

NG

20.READ VALUE USING GTS (EXHAUST TEMPERATURE DURING FORCIBLE REGENERATION FUNCTION)
13.READ VALUE USING GTS (EXHAUST TEMPERATURE DURING FORCIBLE REGENERATION FUNCTION)
a.

Read the exhaust gas temperature just before the forcible regeneration function is completed.

Standard:
Condition Exhaust Temperature B1S3
During forcible regeneration function 480°C (896°F) or more



Result:
Proceed to
OK
NG



OK

14.READ VALUE USING GTS (DIFFERENTIAL PRESSURE)

NG

25.READ VALUE USING GTS (INJECTION VOLUME DURING FORCIBLE REGENERATION FUNCTION)
14.READ VALUE USING GTS (DIFFERENTIAL PRESSURE)
a.

After the forcible regeneration is completed, allow the engine to idle for at least 5 minutes.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.


f.

Check the differential pressure when the exhaust gas temperature sensor indicates 200°C or less.

HINT:
·

If the exhaust gas temperature is high, the differential pressure cannot be measured correctly.

·

If the differential pressure is outside the normal range, the center exhaust pipe assembly (catalytic converter) may have deteriorated or the center exhaust pipe assembly (catalytic converter) may be clogged with PM.

·

Fully depress the accelerator pedal and when the engine speed becomes stable, promptly read the differential pressure.



Standard:
Engine Speed Differential Pressure
3300 to 3400 rpm (no engine load) Less than 15 kPa



Result:
Proceed to
OK
NG



OK

15.CHECK ENGINE OIL LEVEL

NG

REPLACE CENTER EXHAUST PIPE ASSEMBLY

15.CHECK ENGINE OIL LEVEL
a.

Check the engine oil level.


Result:
Proceed to
OK
NG



OK

END

NG

REPLACE ENGINE OIL

16.CLEAN EXHAUST SYSTEM
a.

Remove the catalytic converter and the monolithic converter.


b.

Blow air to clean the catalytic converter, or soak it in water and wash off the soot.

NOTICE:
·

Make sure to clean both oxidation catalyst and DPF catalyst.

·

After installing the catalytic converter, increase idling speed until steam is no longer emitted.




c.

Reinstall the catalytic converter and the monolithic converter.


Result:
Proceed to
NEXT



NEXT

17.READ VALUE USING GTS (DIFFERENTIAL PRESSURE)
17.READ VALUE USING GTS (DIFFERENTIAL PRESSURE)
a.

Allow the engine to idle for at least 5 minutes.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.


e.

Read the value.

HINT:
·

If the exhaust gas temperature is high, the differential pressure cannot be measured correctly.

·

If the differential pressure is outside the normal range, the center exhaust pipe assembly (catalytic converter) may have deteriorated or the center exhaust pipe assembly (catalytic converter) may be clogged with PM.

·

Fully depress the accelerator pedal and when the engine speed becomes stable, promptly read the differential pressure.




Result:
Engine Speed (no engine load) Differential Pressure Proceed to
3300 to 3400 rpm (Exhaust gas temperature (up stream) is 200°C or less) 25 kPa or more A
Less than 25 kPa B



A

REPLACE CENTER EXHAUST PIPE ASSEMBLY

B

10.READ VALUE USING GTS (EXHAUST TEMPERATURE DURING FORCIBLE REGENERATION FUNCTION)
18.READ VALUE USING GTS (INJECTION VOLUME)
a.

Cease the forcible regeneration function.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Injection Volume.


f.

Read the value.

Standard:
Condition Injection Volume
Idling 5.0 to 12.0 mm3/st



Result:
Result Proceed to
NG A
OK B



A

19.REPLACE INJECTOR ASSEMBLY

B

21.ADJUST EXHAUST RETARDER ASSEMBLY
19.REPLACE INJECTOR ASSEMBLY
a.

Replace the injector assembly (Click here Engine / Hybrid System>N04C-VJ (FUEL)>FUEL INJECTOR>REMOVAL).


Result:
Proceed to
NEXT



NEXT

20.READ VALUE USING GTS (EXHAUST TEMPERATURE DURING FORCIBLE REGENERATION FUNCTION)
a.

Read the exhaust gas temperature B1S4 during the forcible regeneration function.

Standard:
Condition Exhaust Temperature B1S4
During forcible regeneration function 220°C (428°F) or more



Result:
Proceed to
OK
NG



OK

REPLACE NO. 3 EXHAUST TEMPERATURE SENSOR

NG

22.READ VALUE USING GTS (INJECTION VOLUME DURING FORCIBLE REGENERATION FUNCTION)
21.ADJUST EXHAUST RETARDER ASSEMBLY
a.

Adjust the exhaust retarder gap (widen the gap).

Click hereBrake>EXHAUST BRAKE>EXHAUST BRAKE RETARDER>INSPECTION


Result:
Proceed to
NEXT



NEXT

22.READ VALUE USING GTS (INJECTION VOLUME DURING FORCIBLE REGENERATION FUNCTION)
a.

Read the injection volume during the forcible regeneration function.

Standard:
Condition Injection Volume
During forcible regeneration function 13 to 20 mm3/st



Result:
Proceed to
OK
NG



OK

23.CHECK FOR EXHAUST GAS LEAK

NG

24.ADJUST EXHAUST RETARDER ASSEMBLY
23.CHECK FOR EXHAUST GAS LEAK
a.

Check the exhaust gas leak.


Result:
Proceed to
NEXT



NEXT

24.ADJUST EXHAUST RETARDER ASSEMBLY
a.

Adjust the exhaust retarder gap (widen the gap).

Click hereBrake>EXHAUST BRAKE>EXHAUST BRAKE RETARDER>INSPECTION


Result:
Proceed to
NEXT



NEXT

25.READ VALUE USING GTS (INJECTION VOLUME DURING FORCIBLE REGENERATION FUNCTION)
a.

Read the injection volume during the forcible regeneration function.

Standard:
Condition Injection Volume
During forcible regeneration function 13 to 20 mm3/st



Result:
Proceed to
OK
NG



OK

26.READ VALUE USING GTS (FUEL PRESS)

NG

28.ADJUST EXHAUST RETARDER ASSEMBLY
26.READ VALUE USING GTS (FUEL PRESS)
a.

Cease the forcible regeneration function.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menu items: Powertrain / Engine and ECT / Data List / Fuel Press.


f.

Check that the internal fuel pressure of the common rail is within the specification below.

Standard:
Engine Speed Fuel Pressure
Idling Approximately 20000 to 30000 kPa



Result:
Proceed to
OK
NG



OK

27.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY

NG

REPAIR OR REPLACE FUEL SYSTEM

27.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY
a.

Inspect the injection or supply pump assembly (Click here Engine / Hybrid System>N04C-VJ (FUEL)>FUEL SUPPLY PUMP>INSPECTION).


Result:
Result Proceed to
NG A
OK B



A

B

15.CHECK ENGINE OIL LEVEL
28.ADJUST EXHAUST RETARDER ASSEMBLY
a.

Adjust the exhaust retarder gap (widen the gap).

Click hereBrake>EXHAUST BRAKE>EXHAUST BRAKE RETARDER>INSPECTION


Result:
Proceed to
NEXT



NEXT