Home › Drivetrain › M15# (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSMISSION ASSEMBLY (for M155) › from 2021.01
RM2850E _52 Drivetrain _073186 M15# MANUAL TRANSMISSION / TRANSAXLE _0356146 MANUAL TRANSMISSION ASSEMBLY(for M155) A

M15# MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION ASSEMBLY(for M155)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 2.DRAIN MANUAL TRANSMISSION OIL

a.

Remove the drain plug and gasket, and then drain the manual transmission oil.


b.

Install a new gasket and the drain plug.

Torque:

37 N*m (379 kgf*cm, 27 ft.*lbf)



Hide 37110F 3.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

Hide 17571 4.REMOVE NO. 1 EXHAUST PIPE SUPPORT BRACKET

a.

w/o Transmission Air Guide:

i.
C249235

Loosen the clamp bolt.


ii.

Remove the 2 bolts and the No. 1 exhaust pipe support bracket from the manual transmission assembly.



b.

w/ Transmission Air Guide:

i.
C249236

Loosen the clamp bolt.


ii.

Remove the 4 bolts, transmission air guide and the No. 1 exhaust pipe support bracket from the manual transmission assembly.



Hide 17410 5.REMOVE FRONT EXHAUST PIPE ASSEMBLY

a.

w/o Exhaust Brake:

i.
C249752

Remove the 4 bolts, 2 gaskets and the front exhaust pipe spacer from the exhaust pipe.


ii.
C249216

Remove the 3 nuts and the front exhaust pipe assembly from the exhaust manifold.


iii.

Remove the gasket.



b.

w/ Exhaust Brake:

i.
C249237

Disconnect the vacuum hose from the exhaust retarder assembly.


ii.

Remove the 4 bolts, 2 gaskets and the exhaust retarder assembly from the exhaust pipe.


iii.
C249216

Remove the 3 nuts and the front exhaust pipe assembly from the exhaust manifold.


iv.

Remove the gasket.



Hide 46501 6.REMOVE PARKING BRAKE DRUM SUB-ASSEMBLY (for Short Wheelbase)

Hide 46501 7.REMOVE PARKING BRAKE DRUM SUB-ASSEMBLY (for Long Wheelbase)

Hide 46503C 8.SEPARATE PARKING BRAKE PLATE SUB-ASSEMBLY

a.
C249239E02
0.188,0.156 0.427,0.354 0.24,0.198 10 false *A 0.188,2.323 0.469,2.521 0.281,0.198 10 false *B

Remove the 4 bolts and separate the parking brake plate sub-assembly from the manual transmission assembly.

Text in Illustration
*A for Short Wheelbase
*B for Long Wheelbase

HINT:

Using a piece of rope, hang the parking brake plate sub-assembly to the vehicle.



Hide 33820B 9.DISCONNECT SHIFT AND SELECT TRANSMISSION CONTROL CABLE (for LHD)

a.
C249218

Remove the 2 nuts and 2 clips, and disconnect the shift and select transmission control cables from the manual transmission assembly.


Hide 33709F 10.REMOVE FLOOR SHIFT CROSS SHAFT SUB-ASSEMBLY (for RHD)

a.
C249219

Remove the 2 nuts and disconnect the shift lever side of the shift and select transmission control links.


b.
C249220

Remove the 2 nuts and disconnect the transmission side of the shift and select transmission control links.


c.
C249221

Remove the 4 bolts and the floor shift cross shaft sub-assembly from the manual transmission assembly.


Hide 31470 11.SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY

a.
C249223

Remove the 2 bolts and separate the clutch release cylinder assembly.

HINT:

Using a piece of rope, hang the clutch release cylinder assembly to the vehicle.



Hide 28100 12.REMOVE STARTER ASSEMBLY

a.

Remove the nut and disconnect the starter wire from the terminal 30.


b.

Disconnect the terminal 50 connector from the starter assembly.


c.

Remove the bolt, nut, washer and the starter assembly from the manual transmission assembly.


Hide 13.DISCONNECT CONNECTOR

a.

Disconnect the connectors and wire harness clamps from the manual transmission assembly.


Hide 33119 14.REMOVE STIFFENER PLATE LH

C249243

a.

Remove the 4 bolts and the stiffener plate LH from the manual transmission assembly.


Hide 33118 15.REMOVE STIFFENER PLATE RH

C249244

a.

Remove the 4 bolts and the stiffener plate RH from the manual transmission assembly.


Hide 33110 16.SUPPORT MANUAL TRANSMISSION ASSEMBLY

a.

Support the manual transmission assembly with a transmission jack.


Hide 51204 17.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.
A102004

Remove the 12 bolts and separate the No. 3 frame crossmember sub-assembly from the frame.


b.
A102003

Remove the 4 nuts, 4 washers and the No. 3 frame crossmember sub-assembly from the engine mounting brackets.


Hide 11000 18.SUPPORT ENGINE ASSEMBLY

a.

Support the engine assembly with a transmission jack.

NOTICE:
·

Make sure to support the engine assembly securely to prevent it from tilting when the manual transmission assembly has been removed.

·

Do not tilt the engine assembly and the manual transmission assembly more than necessary.




Hide 33110 19.REMOVE MANUAL TRANSMISSION ASSEMBLY (for LHD)

a.
C249246

Remove the 5 bolts, 2 washers and the No. 1 transmission control cable bracket.


b.

Remove the manual transmission assembly.

NOTICE:
·

To avoid damage to the knock pins, do not pry between the manual transmission assembly and the engine assembly.

·

To avoid damage to the input shaft, do not forcefully shake the manual transmission assembly.




Hide 33110 20.REMOVE MANUAL TRANSMISSION ASSEMBLY (for RHD)

a.
C249247

Remove the 5 bolts.


b.

Remove the manual transmission assembly.

NOTICE:
·

To avoid damage to the knock pins, do not pry between the manual transmission assembly and the engine assembly.

·

To avoid damage to the input shaft, do not forcefully shake the manual transmission assembly.




Hide 12325 21.REMOVE NO. 3 ENGINE MOUNTING BRACKET

a.
C249228

Remove the 4 bolts and the No. 3 engine mounting bracket from the manual transmission assembly.


Hide 12321 22.REMOVE NO. 1 ENGINE MOUNTING BRACKET

a.
C249229

Remove the 4 bolts and the No. 1 engine mounting bracket from the manual transmission assembly.


Hide 31230 23.REMOVE CLUTCH RELEASE BEARING ASSEMBLY

C249230

a.

Separate the clutch release fork sub-assembly from the release fork support.


b.

Remove the clutch release bearing assembly with the clutch release fork sub-assembly from the manual transmission assembly.


Hide 31204 24.REMOVE CLUTCH RELEASE FORK SUB-ASSEMBLY

a.

Disengage the release bearing hub clip and remove the clutch release fork sub-assembly from the clutch release bearing assembly.


Hide 31126 25.REMOVE CLUTCH RELEASE FORK BOOT

a.

Remove the clutch release fork boot from the manual transmission assembly.


Hide 31236B 26.REMOVE RELEASE FORK SUPPORT

a.
C249231

Remove the release fork support from the manual transmission assembly.


Hide 31111 27.REMOVE CLUTCH HOUSING

C249232

a.

Remove the 9 bolts and the clutch housing from the manual transmission assembly.