Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM J

N04C-VJ ENGINE CONTROL  ECD SYSTEM  Fuel Injection System  


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the suction control valve or the injection or supply pump assembly, the ECM needs initialization (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injector assembly, the ECM needs registration (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press and Target Common Rail Pressure.


e.

Confirm the values for "Fuel Press" and "Target Common Rail Pressure" when the engine is started.

A255599E04
2.552,2.458 2.792,2.219 false 2.198,2.677 2.521,2.969 false 0.104,0.479 0.74,0.844 0.635,0.365 10 false Fuel Pressure 5.583,3.375 5.979,3.563 0.396,0.188 10 false Time 2.552,2.896 4.49,3.052 1.938,0.156 10 false Target Common Rail Pressure 2.844,2.156 3.583,2.344 0.74,0.188 10 false Fuel Press 3.427,0.552 4.26,0.75 0.833,0.198 10 false 222000 kPa 2.594,0.896 6.271,1.49 3.677,0.594 10 false There is a possibility that the fuel pressure is not being regulated, and the fuel pressure is only decreasing because the pressure limiter opened. 1.396,3.448 2.229,3.604 0.833,0.156 10 false Engine Start

Result:
Result Proceed to
Except below A
"Fuel Press" at engine start is more than 222000 kPa B


HINT:
·

Normally, "Fuel Press" does not reach 222000 kPa when the engine is started.

·

If "Fuel Press" reaches 222000 kPa when the engine is started, the suction control valve may not be operating (current may not be reaching the suction control valve).





A

2.READ VALUE USING GTS

B

9.CHECK COMMON RAIL ASSEMBLY
2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press and Target Common Rail Pressure.


e.

Confirm the values for "Fuel Press" and "Target Common Rail Pressure" when the engine is started, and when accelerating and decelerating the vehicle.

A255597E03
0.104,0.292 1.073,0.469 0.969,0.177 10 false Fuel Pressure 2.906,2.135 3.302,2.323 0.396,0.188 10 false Time 5.115,5.885 7.052,6.083 1.938,0.198 10 false Target Common Rail Pressure 5.125,5.552 5.865,5.74 0.74,0.188 10 false Fuel Press 5.365,0.615 6.198,0.813 0.833,0.198 10 false 222000 kPa 0.104,2.417 1.063,2.615 0.958,0.198 10 false Fuel Pressure 2.906,4.25 3.302,4.438 0.396,0.188 10 false Time 0.104,4.531 1.073,4.708 0.969,0.177 10 false Fuel Pressure 2.906,6.344 3.302,6.531 0.396,0.188 10 false Time 3.427,0.427 4.396,0.604 0.969,0.177 10 false Fuel Pressure 6.167,2.385 6.563,2.573 0.396,0.188 10 false Time 3.427,2.979 4.406,3.177 0.979,0.198 10 false Fuel Pressure 6.167,4.938 6.563,5.125 0.396,0.188 10 false Time 0.448,0.094 0.875,0.292 0.427,0.198 10 false Fig. 1 0.448,2.24 0.854,2.438 0.406,0.198 10 false Fig. 2 3.74,0.104 4.24,0.313 0.5,0.208 10 false Fig. 3 3.74,2.75 4.156,2.979 0.417,0.229 10 false Fig. 4 0.448,4.333 0.896,4.531 0.448,0.198 10 false Fig. 5 5.385,3.094 6.219,3.292 0.833,0.198 10 false 222000 kPa 0.563,0.521 2.792,0.885 2.229,0.365 10 false When depressing and releasing the accelerator pedal 3.854,0.896 6.552,1.094 2.698,0.198 10 false After starting the engine, and then idling it 0.552,2.604 2.792,2.969 2.24,0.365 10 false When depressing and releasing the accelerator pedal 0.865,4.844 2.979,5.031 2.115,0.188 10 false When accelerating at full throttle 3.99,4.979 4.875,5.188 0.885,0.208 10 false Engine Start 3.969,2.427 4.896,2.656 0.927,0.229 10 false Engine Start

Result:
Result Proceed to
Except below A
Fuel Press" is constantly fluctuating and differs from "Target Common Rail Pressure" as shown in figure 1 B
"Fuel Press" greatly overshoots "Target Common Rail Pressure" and differs substantially from "Target Common Rail Pressure" as shown in figure 2
Engine does not start, takes a long time to start, or starts but "Fuel Press" is less than "Target Common Rail Pressure" as shown in figure 3
After the engine starts, "Fuel Press" becomes much higher than "Target Common Rail Pressure" and hardly decreases at all as shown in figure 4
"Fuel Press" fluctuates during acceleration or right after accelerating as shown in figure 5 C


HINT:
·

The cases shown in figure 3 and 4 may occur when the learned value for the injection or supply pump assembly is incorrect immediately after the suction control valve, the injection or supply pump assembly, the fuel filter, or the ECM is replaced.

·

If "Fuel Press" fluctuates during acceleration as shown in figure 5, there may be air in the fuel system due to an increase in fuel suction vacuum.





A

3.PERFORM ACTIVE TEST USING GTS

B

11.PERFORM INITIALIZATION

C

7.CHECK FOR CLOGS IN FUEL SUCTION PIPES AND AIR IN FUEL
3.PERFORM ACTIVE TEST USING GTS
HINT:

By performing this Active Test, the engine speed is maintained at 2000 rpm and the common rail assembly internal fuel pressure is raised to the maximum operating pressure. As a result, a fuel leak check can be conducted while retaining the high common rail pressure.


a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.


e.

Visually check the injection or supply pump assembly, injector assembly and fuel line located between the injection or supply pump assembly and common rail assembly for fuel leaks and fuel pressure leaks. Also, perform the same check on the fuel line between the common rail assembly and the injector assembly.

HINT:

There may be fuel leaks inside the components, such as the injection or supply pump assembly.



Result:
Result Proceed to
No fuel leaks exist A
Fuel leaks exist B



A

4.READ VALUE USING GTS

B

REPAIR FUEL LEAK

4.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press and Target Common Rail Pressure.


e.

Confirm the values for "Fuel Press" and "Target Common Rail Pressure" when the accelerator pedal is depressed and then released.

A255598E05
3.844,1.708 4.198,1.302 false 3.24,1.875 2.885,2.24 false 0.073,0.333 0.708,0.698 0.635,0.365 10 false Fuel Pressure 5.458,3.323 5.854,3.51 0.396,0.188 10 false Time 0.969,2.177 2.917,2.385 1.948,0.208 10 false Target Common Rail Pressure 4.25,1.24 4.99,1.427 0.74,0.188 10 false Fuel Press 4.135,0.5 4.969,0.698 0.833,0.198 10 false 222000 kPa


Result:
Result Proceed to
After the accelerator pedal is depressed, "Fuel Press" exceeds 222000 kPa and then decreases. A
Except above B



A

5.CHECK FOR CLOGGING IN INJECTOR RETURN PIPE

B

6.READ VALUE USING GTS
5.CHECK FOR CLOGGING IN INJECTOR RETURN PIPE
a.

Check for clogs in the return line for the injector assembly.

OK:

No clogs in the fuel line



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS

NG

REPAIR OR REPLACE FUEL PIPING CLOG

6.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press and Target Common Rail Pressure.


e.

Confirm the values for "Fuel Press" and "Target Common Rail Pressure" when the engine speed is gradually raised from idle to 3000 rpm.

A255600E04
0.052,0.656 1.021,0.833 0.969,0.177 10 false Fuel Pressure 3.042,2.615 3.438,2.802 0.396,0.188 10 false Time 4.51,5.281 6.448,5.5 1.938,0.219 10 false Target Common Rail Pressure 4.542,4.813 5.281,5 0.74,0.188 10 false Fuel Press 0.052,3.25 1.021,3.427 0.969,0.177 10 false Fuel Pressure 3.042,5.135 3.438,5.323 0.396,0.188 10 false Time 3.563,0.656 4.531,0.854 0.969,0.198 10 false Fuel Pressure 6.302,2.615 6.698,2.802 0.396,0.188 10 false Time 0.146,0.167 0.594,0.365 0.448,0.198 10 false Fig. 1 0.146,2.844 0.51,3.052 0.365,0.208 10 false Fig. 3 3.688,0.167 4.167,0.385 0.479,0.219 10 false Fig. 2 0.604,0.396 3.563,0.615 2.958,0.219 10 false When the engine speed is gradually increased 3.823,0.417 6.76,0.625 2.938,0.208 10 false When the engine speed is gradually increased 0.604,2.948 3.5,3.167 2.896,0.219 10 false When the engine speed is gradually increased

Result:
Result Proceed to
"Fuel Press" becomes unstable in a certain engine speed range and stops following "Target Common Rail Pressure" as shown in figure 1 A
"Fuel Press" is continually low and does not follow "Target Common Rail Pressure" as shown in figure 2
"Fuel Press" changes with no relation to "Target Common Rail Pressure" as shown in figure 3 B
Except above C


HINT:
·

The cases shown in figure 1 and 2 occur when the amount of fuel supplied by the injection or supply pump assembly is insufficient.

·

When the amount of fuel supplied is insufficient, the fuel filter or a fuel pipe being clogged is usually the cause.





A

7.CHECK FOR CLOGS IN FUEL SUCTION PIPES AND AIR IN FUEL

C

11.PERFORM INITIALIZATION

B

8.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
7.CHECK FOR CLOGS IN FUEL SUCTION PIPES AND AIR IN FUEL
a.

Check that there are no clogs in the fuel filter, fuel pipes and fuel suction port in the fuel tank.


b.

Check that the amount of fuel is sufficient.


c.

Inspect the fuel tank, the fuel pipes, the injection or supply pump assembly, the common rail assembly and the injector assemblies for fuel leaks and seepage.


d.

Check if fuel waxing has occurred due to low temperatures.

HINT:

Once fuel waxing occurs, the engine needs to be run for a long time in order for the wax to melt.



e.

Check if the fuel pipes are bent or deformed, preventing fuel from flowing.


Result:
Proceed to
OK
NG



OK

11.PERFORM INITIALIZATION

NG

CHECK AND REPAIR FUEL PIPING CLOG (INCLUDING FUEL FREEZING)

8.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the fuel pressure sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B105-16 (PCR1) - B93-2 (PCR1) Always Below 1 Ω
B104-13 (VC) - B93-1 (VC1) Always Below 1 Ω
B104-14 (E2) - B93-3 (E1) Always Below 1 Ω
B105-2 (PCR2) - B93-5 (PCR2) Always Below 1 Ω
B105-13 (VC2) - B93-6 (VC2) Always Below 1 Ω
B105-14 (E21) - B93-4 (E2) Always Below 1 Ω
B105-16 (PCR1) or B93-2 (PCR1) - Body ground Always 10 kΩ or higher
B104-13 (VC) or B93-1 (VC1) - Body ground Always 10 kΩ or higher
B105-2 (PCR2) or B93-5 (PCR2) - Body ground Always 10 kΩ or higher
B105-13 (VC2) or B93-6 (VC2) - Body ground Always 10 kΩ or higher
B104-14 (E2) or B93-3 (E1) - Other terminals Always 10 kΩ or higher
B105-14 (E21) or B93-4 (E2) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK COMMON RAIL ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL PRESSURE SENSOR - ECM)

9.CHECK COMMON RAIL ASSEMBLY
OK:

Fuel does not return from the fuel line of the pressure limiter.


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)

NG

REPLACE COMMON RAIL ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
a.

Disconnect the suction control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B103-23 (PCV+) - B52-1 (SCV+) Always Below 1 Ω
B103-12 (PCV-) - B52-2 (SCV-) Always Below 1 Ω
B103-23 (PCV+) or B52-1 (SCV+) - Body ground Always 10 kΩ or higher
B103-12 (PCV-) or B52-2 (SCV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.PERFORM INITIALIZATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SUCTION CONTROL VALVE - ECM)

11.PERFORM INITIALIZATION
a.

Perform fuel supply pump initialization (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


Result:
Proceed to
NEXT



NEXT

12.READ VALUE USING GTS
12.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press and Target Common Rail Pressure.


e.

Perform procedures 1, 2, 4 and 6 and check if the problem symptom disappears.

Result:
Result Proceed to
Problem symptom does not disappear A
Problem symptom disappears B


HINT:
·

If the problem symptom disappears, a fuel line may be clogged.

·

After checking for clogs in the fuel lines and performing repairs, perform fuel supply pump initialization (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).





A

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY

B

7.CHECK FOR CLOGS IN FUEL SUCTION PIPES AND AIR IN FUEL