Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0110  Intake Air Temperature Circuit Malfunction  P0112  Intake Air Temperature Circuit Low Input  P0113  Intake Air Temperature Circuit High Input  


DESCRIPTION

A373795E01
1.344,1.813 1.813,1.563 false 0.552,3.906 0.906,4.167 0.354,0.26 10 false -20 0.625,4.063 0.781,4.26 0.156,0.198 10 false -4 0.969,4.063 1.188,4.271 0.219,0.208 10 false 32 1.344,4.063 1.615,4.323 0.271,0.26 10 false 68 1.677,4.063 1.958,4.302 0.281,0.24 10 false 104 3.052,4.063 3.406,4.313 0.354,0.25 10 false (°F) 3.042,3.875 3.385,4.125 0.344,0.25 10 false (°C) 1.552,4.354 2.448,4.583 0.896,0.229 10 false Temperature 0.073,0.01 0.615,0.281 0.542,0.271 10 false Fig. 1: 0.083,0.26 1.146,0.552 1.063,0.292 10 false Resistance 0.396,0.479 0.969,0.792 0.573,0.313 10 false (kΩ) 0.281,0.646 0.521,0.906 0.24,0.26 10 false 30 0.281,0.854 0.51,1.125 0.229,0.271 10 false 20 0.281,1.177 0.5,1.385 0.219,0.208 10 false 10 0.354,1.51 0.594,1.76 0.24,0.25 10 false 5 0.344,1.76 0.604,2 0.26,0.24 10 false 3 0.344,2 0.594,2.26 0.25,0.26 10 false 2 0.354,2.313 0.656,2.583 0.302,0.271 10 false 1 0.25,3.458 0.5,3.698 0.25,0.24 10 false 0.1 0.25,3.135 0.49,3.385 0.24,0.25 10 false 0.2 0.25,2.917 0.5,3.167 0.25,0.25 10 false 0.3 0.26,2.677 0.531,2.927 0.271,0.25 10 false 0.5 1.865,1.448 2.688,1.75 0.823,0.302 10 false Acceptable 1,3.896 1.354,4.156 0.354,0.26 10 false 0 1.344,3.896 1.698,4.156 0.354,0.26 10 false 20 1.729,3.896 2.083,4.156 0.354,0.26 10 false 40 2.104,3.896 2.458,4.156 0.354,0.26 10 false 60 2.448,3.896 2.802,4.156 0.354,0.26 10 false 80 2.729,3.896 3.083,4.156 0.354,0.26 10 false 100 2.042,4.063 2.323,4.302 0.281,0.24 10 false 140 2.385,4.063 2.667,4.302 0.281,0.24 10 false 176 2.729,4.063 3.01,4.302 0.281,0.24 10 false 212

The intake air temperature sensor, mounted on the mass air flow meter sub-assembly, monitors the intake air temperature. The intake air temperature sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (see Fig. 1).

The intake air temperature sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.

Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes, the voltage at terminal THA varies accordingly. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

HINT:

When DTC P0110, P0112 or P0113 is stored, the ECM enters fail-safe mode. During fail-safe mode, the intake air temperature is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is detected.



DTC No. DTC Detection Condition Trouble Area
P0110 Open or short in intake air temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Open or short in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

ECM


P0112 Short in intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic)
·

Short in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

ECM


P0113 Open in intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic)
·

Open in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

ECM



HINT:

When any of these DTCs are output, check the intake air temperature using the intelligent tester. Enter the following menus: Powertrain / Engine / Data List / All Data / Intake Air.

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) Short circuit


WIRING DIAGRAM

A255126E39
0.117,2.726 0.388,2.874 0.271,0.147 10 D3 0.117,2.894 2.699,3.233 2.582,0.339 10 Intake Air Temperature Sensor (Built into Mass Air Flow Meter Sub-assembly) 1.603,1.48 1.906,1.633 0.303,0.153 10 THA 1.709,2.088 1.907,2.235 0.198,0.147 10 E2 1.987,1.485 2.094,1.634 0.107,0.149 10 1 1.987,2.088 2.094,2.238 0.107,0.149 10 2 5.409,1.48 5.712,1.633 0.303,0.153 10 THA 5.13,1.484 5.306,1.630 0.175,0.146 10 71 5.13,2.088 5.338,2.234 0.208,0.146 10 74 5.409,2.088 5.814,2.242 0.406,0.153 10 ETHA 5.989,1.359 6.116,1.513 0.128,0.155 10 R 6.014,1.069 6.259,1.219 0.245,0.150 10 5 V 6.058,3.109 6.396,3.264 0.339,0.155 10 ECM 5.81,3.109 6.066,3.257 0.256,0.147 10 D1

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Intake Air.


e.

Read the value displayed on the tester.

OK:

Same as actual intake air temperature.


Result
Result Proceed to
-40°C (-40°F) A
140°C (284°F) B
Same as actual intake air temperature C

HINT:
·

If there is an open circuit, the tester indicates -40°C (-40°F).


·

If there is a short circuit, the tester indicates 140°C (284°F).





A

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
a.
U188315E01
0.404,0.258 1.159,0.439 0.755,0.182 10 MAF Meter 2.551,0.133 2.906,0.308 0.355,0.174 10 ECM 2.448,0.984 2.780,1.144 0.332,0.161 8 THA 2.445,1.173 2.848,1.320 0.404,0.147 8 ETHA 0.043,2 1.357,2.168 1.314,0.168 10 Wire Harness Side: 0.841,2.396 2.270,2.557 1.429,0.161 10 MAF Meter Connector 2.502,2.746 3.195,2.906 0.693,0.161 10 Front View 0.394,3.353 0.597,3.515 0.203,0.162 10 D3 0.52,3.869 0.856,4.029 0.336,0.161 10 THA 1.305,4.052 1.525,4.212 0.221,0.161 10 E2 0.866,3.917 1.373,3.456 false 1.425,4.028 1.576,3.485 false

Disconnect the mass air flow meter sub-assembly connector.


b.

Connect terminals 1 (THA) and 2 (E2) of the mass air flow meter sub-assembly wire harness side connector.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the tester on.


f.

Enter the following menus: Powertrain / Engine / Data List / All Data / Intake Air.


g.

Read the value displayed on the tester.

Standard value:

140°C (284°F)




OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D1-71 (THA) - D3-1 (THA) Always Below 1 Ω
D1-74 (ETHA) - D3-2 (E2) Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
a.
A242995E03
0.406,0.115 0.74,0.281 0.333,0.167 10 false D3 0.406,0.313 1.115,0.479 0.708,0.167 10 false MAF Meter 2.521,0.177 2.875,0.344 0.354,0.167 10 false ECM 2.521,1.073 2.875,1.24 0.354,0.167 10 false THA 2.5,1.521 2.969,1.667 0.469,0.146 10 false ETHA

Disconnect the mass air flow meter sub-assembly connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine / Data List / All Data / Intake Air.


f.

Read the value displayed on the tester.

Standard value:

-40°C (-40°F)




OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-71 (THA) or D3-1 (THA) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR