Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM J

2GR-FE ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

WIRING DIAGRAM

PROCEDURE

1.CHECK FUEL PUMP (FUEL PUMP OPERATION)
a.

Check if there is pressure in the fuel inlet hose.

HINT:

If there is fuel pressure, you will hear the sound of fuel flowing.




NG

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CIRCUIT OPENING RELAY)

OK

9.INSPECT F/PMP RELAY
2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CIRCUIT OPENING RELAY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the intelligent tester ON.


c.

Enter the following menus: Power train / Engine / Active Test / Control the Fuel Pump / Speed.


d.

Check the operation of the relay while operating it using the intelligent tester.

OK:

Operating noise can be heard from the relay.




NG

3.CHECK C/OPN RELAY TERMINAL

OK

6.CHECK C/OPN RELAY TERMINAL
3.CHECK C/OPN RELAY TERMINAL
a.
A135435E01
0.576,0.542 2.586,0.708 2.010,0.166 10 Engine Room No. 1 Relay Block 0.178,2.009 1.062,2.339 0.883,0.330 10 C/OPN Relay Holder

Remove the C/OPN relay from the engine room No. 1 relay block.


b.

Measure the voltage of the engine room No. 1 relay block terminal when the engine switch is turned on (IG) and off.

Standard voltage:
Tester Connection Condition Specified Condition
C/OPN relay holder terminal (1) - Body ground Engine switch off Below 1 V
C/OPN relay holder terminal (1) - Body ground Engine switch on (IG) 11 to 14 V




OK

4.INSPECT C/OPN RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGN FUSE - C/OPN RELAY)

4.INSPECT C/OPN RELAY
a.
B016200

Remove the C/OPN relay from the engine room No. 1 relay block.


b.

Measure the resistance.

Standard resistance:
Tester Connection Specified Condition
3 - 5 10 kΩ or higher
Below 1 Ω
(when battery voltage is applied to terminals 1 and 2)


HINT:

Relay coil circuit between 1 and 2 is not through IGN fuse.




OK

5.CHECK HARNESS AND CONNECTOR (ECM - C/OPN RELAY)

NG

REPLACE C/OPN RELAY

5.CHECK HARNESS AND CONNECTOR (ECM - C/OPN RELAY)
a.

Remove the C/OPN relay from the engine room No. 1 relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance.

Standard resistance (Check for open):
Tester Connection Condition Specified Condition
C/OPN relay holder terminal (2) - A7-7 (FC) Always Below 1 Ω


Standard resistance (Check for short):
Tester Connection Condition Specified Condition
C/OPN relay holder terminal (2) or A7-7 (FC) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK C/OPN RELAY TERMINAL
a.
A135435E01
0.576,0.542 2.586,0.708 2.010,0.166 10 Engine Room No. 1 Relay Block 0.178,2.009 1.062,2.339 0.883,0.330 10 C/OPN Relay Holder

Remove the C/OPN relay from the engine room No. 1 relay block.


b.

Measure the voltage of the engine room No. 1 relay block terminals when the engine switch is turned on (IG) and off.

Standard voltage:
Tester Connection Condition Specified Condition
C/OPN relay holder terminal (5) - Body ground Engine switch off Below 1 V
C/OPN relay holder terminal (5) - Body ground Engine switch on (IG) 11 to 14 V




OK

7.INSPECT FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI MAIN RELAY - C/OPN RELAY)

7.INSPECT FUEL PUMP

OK

8.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - FUEL PUMP - BODY GROUND)

NG

8.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - FUEL PUMP - BODY GROUND)
a.

Check the harness and the connectors between the C/OPN relay and the fuel pump.

i.

Remove the C/OPN relay and F/PMP relay from the engine room No. 1 relay block.


ii.

Disconnect the fuel pump connector.


iii.

Measure the resistance.

Standard resistance (Check for open):
Tester Connection Condition Specified Condition
C/OPN relay holder terminal (3) - F/PMP relay holder terminal (3) Always Below 1 Ω
F/PMP relay holder terminal (4) - M17-4 Always Below 1 Ω


Standard resistance (Check for short):
Tester Connection Condition Specified Condition
C/OPN relay holder terminal (3) or F/PMP relay holder terminal (3) - Body ground Always 10 kΩ or higher
F/PMP relay holder terminal (4) or M17-4 - Body ground Always 10 kΩ or higher




b.

Check the harness and the connectors between the fuel pump and body ground.

i.

Disconnect the fuel pump connector.


ii.

Measure the resistance.

Standard resistance (Check for open):
Tester Connection Condition Specified Condition
M17-5 - Body ground Always Below 1 Ω





OK

CHECK AND REPLACE FUEL FILTER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT F/PMP RELAY
a.
A087121E50
2.333,0.604 2.333,0.292 false 2.49,1.135 2.958,1.135 false 2.49,1.635 2.958,1.635 false 2.031,0.625 1.854,0.313 false 2.625,0.625 2.802,0.313 false 0.313,1.417 0.51,1.625 0.198,0.208 10 false 1 1.792,0.104 1.99,0.313 0.198,0.208 10 false 1 1.313,1.417 1.51,1.625 0.198,0.208 10 false 2 2.792,0.104 2.99,0.313 0.198,0.208 10 false 2 0.313,0.865 0.51,1.073 0.198,0.208 10 false 3 3.01,1.552 3.208,1.76 0.198,0.208 10 false 3 0.938,0.385 1.135,0.594 0.198,0.208 10 false 4 2.302,0.104 2.5,0.313 0.198,0.208 10 false 4 1.313,0.865 1.51,1.073 0.198,0.208 10 false 5 3.01,1.042 3.208,1.25 0.198,0.208 10 false 5

Remove the F/PMP relay from the engine room No. 1 relay block.


b.

Measure the resistance of the F/PMP relay.

Standard resistance:
Tester Connection Specified Condition
3 - 4 Below 1 Ω
3 - 4 10 kΩ or higher
(when battery voltage applied to terminals 1 and 2)
3 - 5 10 kΩ or higher
3 - 5 Below 1 Ω
(when battery voltage applied to terminals 1 and 2)




OK

10.INSPECT FUEL PUMP RESISTOR

NG

INSPECT F/PMP RELAY

10.INSPECT FUEL PUMP RESISTOR
a.
A171796E01
0.144,0.072 1.759,0.346 1.614,0.274 10 Component Side: 0.144,2.069 1.286,2.280 1.142,0.211 10 Label: 0.609,2.868 0.942,2.963 0.333,0.095 2.076,2.687 2.911,2.782 0.836,0.095 0.944,2.928 1.713,2.41 1.713,2.41 2.144,2.911 false 1.042,2.195 2.447,2.410 1.405,0.215 10 Resistance value 2.15,2.868 2.484,2.963 0.333,0.095

Check the resistance value written on the label of the fuel pump resistor.


b.

Measure the resistance of the fuel pump resistor.

Standard resistance:
Label * Tester Connection Condition Specified Condition
0.64 Ω 1-2 always 0.62 to 0.66 Ω
0.32 Ω 1-2 always 0.30 to 0.34 Ω


*: Resistance value written on the label.



OK

11.CHECK HARNESS AND CONNECTOR (F/PMP RELAY - RESISTOR, RESISTOR - FUEL PUMP)

NG

11.CHECK HARNESS AND CONNECTOR (F/PMP RELAY - RESISTOR, RESISTOR - FUEL PUMP)
a.

Check the harness and the connectors between the F/PMP relay and the fuel pump resistor.

i.

Remove the F/PMP relay from the engine room No. 1 relay block.


ii.

Disconnect the fuel pump resistor connector.


iii.

Measure the resistance of the wire harness side connectors.

Standard resistance (Check for open):
Tester Connection Condition Specified Condition
F/PMP relay holder terminal (4) - A11-2 Always Below 1 Ω
F/PMP relay holder terminal (5) - A11-1 Always Below 1 Ω


Standard resistance (Check for short):
Tester Connection Condition Specified Condition
F/PMP relay holder terminal (4) or Fuel pump resistor () - A11-2 Always 10 kΩ or higher
F/PMP relay holder terminal (5) or A11-1 - Body ground Always 10 kΩ or higher





NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

PROCEED TO NEXT INSPECTION PROCEDURE SHOWN IN PROBLEM SYMPTOMS TABLE