Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM J

2GR-FE ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the engine switch is turned on (IG), the battery voltage is applied to terminal IGSW of the ECM. The output signal from terminal MREL of the ECM causes a current to flow to the coil, closing the contacts of the EFI MAIN relay and supplying power to either terminal +B or +B2 of the ECM.

WIRING DIAGRAM

A159631E03
2.188,0.886 2.506,1.051 0.318,0.165 10 G57 2.543,0.886 2.861,1.051 0.318,0.165 10 AM1 2.286,0.699 2.604,0.864 0.318,0.165 10 6 2.188,1.278 2.506,1.443 0.318,0.165 10 G58 2.543,1.278 2.861,1.443 0.318,0.165 10 AM2 2.286,1.091 2.604,1.257 0.318,0.165 10 1 5.307,2.976 5.625,3.141 0.318,0.165 10 A7 5.636,2.878 6.070,3.043 0.434,0.165 10 IGSW 5.322,2.809 5.639,2.974 0.318,0.165 10 28 5.307,4.741 5.625,4.906 0.318,0.165 10 A7 5.355,4.574 5.673,4.739 0.318,0.165 10 1 5.307,5.179 5.625,5.345 0.318,0.165 10 A7 5.636,4.741 5.954,4.906 0.318,0.165 10 +B2 5.307,4.097 5.625,4.262 0.318,0.165 10 A7 5.355,3.93 5.673,4.095 0.318,0.165 10 2 5.636,4.097 5.954,4.262 0.318,0.165 10 +B 5.636,5.179 6.057,5.345 0.420,0.165 10 MREL 5.963,6.197 6.439,6.363 0.476,0.165 10 ECM 5.322,5.012 5.639,5.178 0.318,0.165 10 44 5.307,5.663 5.625,5.828 0.318,0.165 10 D1 5.636,5.663 5.844,5.828 0.208,0.165 10 E1 5.322,5.496 5.639,5.661 0.318,0.165 10 81 3.472,1.084 3.790,1.249 0.318,0.165 10 G58 3.071,1.084 3.495,1.249 0.424,0.165 10 IG2D 3.533,0.897 3.850,1.062 0.318,0.165 10 11 3.662,2.859 3.980,3.024 0.318,0.165 10 3 3.211,3.643 3.529,3.808 0.318,0.165 10 IG2 4.38,3.147 4.698,3.312 0.318,0.165 10 IGN 2.317,3.147 2.635,3.312 0.318,0.165 10 IG2 2.317,4.912 2.635,5.077 0.318,0.165 10 EFI 3.662,3.3 3.980,3.466 0.318,0.165 10 1 2.948,2.859 3.266,3.024 0.318,0.165 10 5 2.948,3.3 3.266,3.466 0.318,0.165 10 2 3.662,4.624 3.980,4.790 0.318,0.165 10 3 3.043,5.409 3.698,5.590 0.656,0.182 10 EFI MAIN 0.808,3.769 1.464,3.919 0.656,0.149 10 F/B BATT 0.808,2.045 1.584,2.191 0.776,0.146 10 AM2 No. 2 2.426,1.617 3.522,1.761 1.096,0.144 10 Main Body ECU 0.808,4.68 1.408,4.834 0.600,0.154 10 FL MAIN 0.934,5.692 1.423,5.861 0.489,0.170 10 Battery 3.662,5.066 3.980,5.231 0.318,0.165 10 1 2.948,4.624 3.266,4.790 0.318,0.165 10 5 2.948,5.066 3.266,5.231 0.318,0.165 10 2 2.195,4.652 2.513,4.818 0.318,0.165 10 1 2.625,4.652 2.943,4.818 0.318,0.165 10 2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (EFI FUSE - BODY GROUND)
a.
A137346E02
0.346,0.421 2.461,0.615 2.115,0.194 10 Engine Room No. 1 Relay Block 0.447,3.192 0.693,3.350 0.246,0.158 10 EFI

Remove the EFI fuse from the engine room No. 1 relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
EFI fuse terminal (1) - Body ground Engine switch on (IG) 11 to 14 V




OK

2.INSPECT FUSE (EFI)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI FUSE - BATTERY)

2.INSPECT FUSE (EFI)
a.

Inspect the EFI fuse.



OK

3.INSPECT EFI MAIN RELAY

NG

REPLACE FUSE

3.INSPECT EFI MAIN RELAY

OK

4.CHECK HARNESS AND CONNECTOR (+B, +B2 AND MREL CIRCUIT)

NG

REPLACE EFI MAIN RELAY

4.CHECK HARNESS AND CONNECTOR (+B, +B2 AND MREL CIRCUIT)
a.

Remove the EFI MAIN relay from the engine room No. 1 relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A7-44 (MREL) - EFI MAIN relay holder terminal (1) Always Below 1 Ω
A7-2 (+B) - EFI MAIN relay holder terminal (3) Always Below 1 Ω
A7-1 (+B2) - EFI MAIN relay holder terminal (3) Always Below 1 Ω
EFI MAIN relay holder terminal (2) - Body ground Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A7-44 (MREL) or EFI MAIN relay holder terminal (1) - Body ground Always 10 kΩ or higher
A7-2 (+B) or EFI MAIN relay holder terminal (3) - Body ground Always 10 kΩ or higher
A7-1 (+B2) or EFI MAIN relay holder terminal (3) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D1-81 (E1) - Body ground Always Below 1 Ω




OK

6.CHECK TERMINAL VOLTAGE (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK TERMINAL VOLTAGE (IGSW VOLTAGE)
a.
U188265E02
2.01,1.656 2.417,2.281 false 2.24,3.552 2.698,3.333 false 0.063,0.083 1.385,0.271 1.323,0.188 10 false Wire Harness Side: 1.333,0.531 2.406,0.75 1.073,0.219 10 false ECM Connector 2.385,2.271 2.604,2.448 0.219,0.177 10 false E1 2.771,3.229 3.198,3.406 0.427,0.177 10 false IGSW 1.479,2.646 2.552,2.865 1.073,0.219 10 false ECM Connector 1.177,2.125 1.906,2.344 0.729,0.219 10 false Front View 1.427,4.302 2.156,4.521 0.729,0.219 10 false Front View 0.823,0.542 1.073,0.719 0.25,0.177 10 false D1 0.969,2.646 1.198,2.823 0.229,0.177 10 false A7

Disconnect the ECM connectors.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-28 (IGSW) - D1-81 (E1) Engine switch on (IG) 11 to 14 V




NG

7.INSPECT FUSE (IGN AND IG2 FUSE)

OK

7.INSPECT FUSE (IGN AND IG2 FUSE)
a.

Inspect the IGN and IG2 fuse.



OK

8.INSPECT IG2 RELAY

NG

REPLACE FUSE

8.INSPECT IG2 RELAY

OK

9.CHECK HARNESS AND CONNECTOR (ECM - ENGINE ROOM NO. 1 RELAY BLOCK (IG2 RELAY))

NG

REPLACE IG2 RELAY

9.CHECK HARNESS AND CONNECTOR (ECM - ENGINE ROOM NO. 1 RELAY BLOCK (IG2 RELAY))
a.

Remove the IG2 relay from the engine room No. 1 relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
IG2 relay holder terminal (3) - A7-28 (IGSW) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
IG2 relay holder terminal (3) or A7-28 (IGSW) - Body ground Always 10 kΩ or higher




NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

10.CHECK HARNESS AND CONNECTOR (IG2 RELAY CIRCUIT)
10.CHECK HARNESS AND CONNECTOR (IG2 RELAY CIRCUIT)
a.

Remove the IG2 relay from the engine room No. 1 relay block.


b.

Remove the instrument panel junction block (main body ECU).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
IG2 relay holder terminal (1) - G58-11 (IG2D) Always Below 1 Ω
IG2 relay holder terminal (2) - Body ground Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
G58-11 (IG2D) - Body ground Always 10 kΩ or higher




NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK