Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0120  Throttle / Pedal Position Sensor / Switch "A" Circuit Malfunction  P0121  Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem  P0122  Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input  P0123  Throttle / Pedal Position Sensor / Switch "A" Circuit High Input  P0220  Throttle / Pedal Position Sensor / Switch "B" Circuit  P0222  Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input  P0223  Throttle / Pedal Position Sensor / Switch "B" Circuit High Input  P2135  Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation  


DESCRIPTION

HINT:

These DTCs relate to the throttle position sensor.


The throttle position sensor is mounted on the throttle with motor body assembly, and detects the opening angle of the throttle valve. This sensor is a non-contact type sensor. It uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds.

The throttle position sensor has 2 sensor circuits, VTA1 and VTA2 each of which transmits a signal. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA1 and VTA2 terminals of the ECM.

As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air fuel ratio correction, power increase correction and fuel-cut control.

U172004E02
5.01,2.135 5.01,1.844 false 4.167,1.083 4.25,0.615 4.25,0.615 4.396,0.615 false 1.031,2.188 1.51,1.229 false 0.969,2.594 0.969,1.75 false 0.99,2.917 0.469,3.5 false 0.99,3.271 1.521,3.646 false 0.896,1.708 0.969,1.75 false 4.688,2.323 4.927,2.479 false 4.635,1.438 4.917,1.646 false 5.01,1.948 5.375,2.25 false 5.531,0.188 5.667,0.188 5.667,0.188 5.885,1.448 false 3.698,1.188 3.99,1.385 0.292,0.198 10 false 4.65 5.396,2.25 5.854,2.469 0.458,0.219 10 false 1.11 V 4.26,1.313 4.719,1.531 0.458,0.219 10 false VTA2 2.396,0.552 4.104,0.781 1.708,0.229 10 false Sensor Output Voltage (V) 4.469,0.542 5.708,0.771 1.24,0.229 10 false Fail-safe Angle 4.156,3.521 6.563,3.719 2.406,0.198 10 false Throttle Valve Opening Angle (°) 3.625,1.885 3.979,2.083 0.354,0.198 10 false 2.55* 3.625,2.396 4.063,2.594 0.438,0.198 10 false 0.93* 3.688,2.063 4.125,2.26 0.438,0.198 10 false 2.25 3.688,2.552 4.125,2.75 0.438,0.198 10 false 0.69 4.979,2.427 5.438,2.646 0.458,0.219 10 false VTA1 4.729,3.188 5.875,3.385 1.146,0.198 10 false Usable Range 3.979,3.292 4.083,3.49 0.104,0.198 10 false 0 4.167,2.833 4.26,3.031 0.094,0.198 10 false 6 6.271,3.281 6.448,3.479 0.177,0.198 10 false 84 0.083,4.385 0.594,4.583 0.51,0.198 10 false Note: 0.083,4.729 3.594,5.094 3.51,0.365 10 false The throttle valve opening angle transmitted through sensor terminal VTA1 is expressed as a percentage. 0.083,5.458 3.281,5.688 3.198,0.229 10 false Between 10% and 22%: Throttle valve fully closed 0.083,5.802 3.188,6.031 3.104,0.229 10 false Between 64% and 96%: Throttle valve fully open 0.083,6.188 3.083,6.417 3,0.229 10 false Approximately 18.6%: Fail safe angle (6°) 1.563,1.104 2.198,1.302 0.635,0.198 10 false Magnet 0.094,4.042 1.615,4.406 1.521,0.365 10 false Throttle Position Sensor 1.563,3.563 2.073,3.76 0.51,0.198 10 false Magnet 0.333,1.604 0.969,1.823 0.635,0.219 10 false IC No. 1 0.26,3.521 0.896,3.74 0.635,0.219 10 false IC No. 2 2.365,4.042 2.875,4.24 0.51,0.198 10 false ECM 1.698,1.969 2.104,2.188 0.406,0.219 10 false VCTA 1.771,3.083 2.125,3.302 0.354,0.219 10 false ETA 1.708,2.354 2.167,2.573 0.458,0.219 10 false VTA1 1.708,2.708 2.167,2.927 0.458,0.219 10 false VTA2 4.031,3.927 5.625,4.125 1.594,0.198 10 false *: During fail-safe control 3.75,5.563 7,5.74 3.25,0.177 10 false VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V 3.75,5.156 5.958,5.354 2.208,0.198 10 false Characteristics of sensor output: 3.844,0.104 5.531,0.313 1.688,0.208 10 false Line indicating VTA2 x 0.8 3.771,0.99 3.979,1.188 0.208,0.198 10 false 5.0

DTC No. DTC Detection Condition Trouble Area
P0120 The output voltage of VTA1 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds or more (1 trip detection logic).
·

Throttle position sensor (built into throttle with motor body assembly)

·

ECM


P0121 The difference between the VTA1 and VTA2 voltages is less than 0.8 V, or higher than 1.6 V for 2 seconds (1 trip detection logic).
·

Throttle position sensor (built into throttle with motor body assembly)

·

Throttle position sensor circuit

·

ECM


P0122 The output voltage of VTA1 is 0.2 V or less for 2 seconds or more (1 trip detection logic).
·

Throttle position sensor (built into throttle with motor body assembly)

·

Short in VTA1 circuit

·

Open in VCTA circuit

·

ECM


P0123 The output voltage of VTA1 is 4.54 V or higher for 2 seconds or more (1 trip detection logic).
·

Throttle position sensor (built into throttle with motor body assembly)

·

Open in VTA1 circuit

·

Open in ETA circuit

·

Short between VCTA and VTA1 circuits

·

ECM


P0220 The output voltage of VTA2 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds or more (1 trip detection logic).
·

Throttle position sensor (built into throttle with motor body assembly)

·

ECM


P0222 The output voltage of VTA2 is 1.75 V or less for 2 seconds or more (1 trip detection logic).
·

Throttle position sensor (built into throttle with motor body assembly)

·

Short in VTA2 circuit

·

Open in VCTA circuit

·

ECM


P0223 The output voltage of VTA2 is 4.8 V or higher, and VTA1 is between 0.2 V and 2.02 V for 2 seconds or more (1 trip detection logic).
·

Throttle position sensor (built into throttle with motor body assembly)

·

Open in VTA2 circuit

·

Open in ETA circuit

·

Short between VCTA and VTA2 circuits

·

ECM


P2135 Either of the following conditions is met (1 trip detection logic):
(a) The difference between the output voltages of VTA1 and VTA2 is 0.02 V or less for 0.5 seconds or more.
(b) The output voltage of VTA1 is 0.2 V or less, and VTA2 is 1.75 V or less for 0.4 seconds or more.
·

Short between VTA1 and VTA2 circuits

·

Throttle position sensor (built into throttle with motor body assembly)

·

ECM



HINT:
·

When any of these DTCs are output, check the throttle valve opening angle using the intelligent tester. Enter the following menus: Powertrain / Engine / Data List / All Data / Throttle Position No. 1 and Throttle Position No. 2.


·

Throttle Position No. 1 is the VTA1 signal, and Throttle Position No. 2 is the VTA2 signal.

Reference (Normal Condition):
Tester Display Accelerator Pedal Fully Released Accelerator Pedal Fully Depressed
Throttle Position No. 1 0.5 to 1.1 V 3.2 to 4.8 V
Throttle Position No. 2 2.1 to 3.1 V 4.6 to 4.98 V




FAIL-SAFE

When any of these DTCs or other DTCs relating to Electronic Throttle Control System (ETCS) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal angle, to allow the vehicle to continue operating at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

Fail-safe mode continues until a pass condition is detected, and the engine switch is then turned off.

WIRING DIAGRAM

A387425E03
0.073,3.396 4.396,3.729 4.323,0.333 10 false Throttle Position Sensor (Built into Throttle with Motor Body Assembly) 1.823,2.573 2.24,2.75 0.417,0.177 10 false E2 0.083,3.229 0.5,3.406 0.417,0.177 10 false D41 1.667,2.01 2.167,2.208 0.5,0.198 10 false VTA2 1.729,1.438 2.229,1.635 0.5,0.198 10 false VTA 1.802,0.854 2.302,1.052 0.5,0.198 10 false VC 2.125,0.719 2.625,0.917 0.5,0.198 10 false 5 2.125,1.302 2.625,1.5 0.5,0.198 10 false 6 2.125,1.885 2.625,2.083 0.5,0.198 10 false 4 2.125,2.438 2.625,2.635 0.5,0.198 10 false 3 5.354,3.323 5.771,3.5 0.417,0.177 10 false D1 5.625,3.323 6.042,3.5 0.417,0.177 10 false ECM 5.094,2.448 5.51,2.625 0.417,0.177 10 false ETA 5.094,1.292 5.625,1.49 0.531,0.198 10 false VTA1 5.094,1.865 5.625,2.063 0.531,0.198 10 false VTA2 5.094,0.729 5.625,0.927 0.531,0.198 10 false VCTA 4.76,0.74 5.292,0.938 0.531,0.198 10 false 96 4.771,1.302 5.302,1.5 0.531,0.198 10 false 98 4.771,1.875 5.302,2.073 0.531,0.198 10 false 99 4.781,2.438 5.313,2.635 0.531,0.198 10 false 97

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Throttle Position No. 1 and Throttle Position No. 2.


e.

Read the values displayed on the tester.

Result
When Accelerator Pedal Fully Released When Accelerator Pedal Fully Depressed Trouble Area Proceed to
Throttle Position No. 1
(VTA1)
Throttle Position No. 2
(VTA2)
Throttle Position No. 1
(VTA1)
Throttle Position No. 2
(VTA2)
0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V VCTA circuit open A
4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V ETA circuit open
0 to 0.2 V,
or 4.5 to 4.98 V
2.1 to 3.1 V
(Fail-safe)
0 to 0.2 V,
or 4.5 to 4.98 V
2.1 to 3.1 V
(Fail-safe)
VTA1 circuit open or shorted to ground
0.6 to 1.4 V
(Fail-safe)
0 to 0.2 V,
or 4.5 to 4.98 V
0.6 to 1.4 V
(Fail-safe)
0 to 0.2 V,
or 4.5 to 4.98 V
VTA2 circuit open or shorted to ground
0.5 to 1.1 V 2.1 to 3.1 V 3.2 to 4.8 V
(Not fail-safe)
4.6 to 4.98 V
(Not fail-safe)
Throttle position sensor circuit normal B

HINT:
·

DTC P0121 is stored when the VTA1 and VTA2 output voltages are not consistent with the sensor characteristics. Therefore, check the freeze frame data when this DTC is stored. Use the following formula to confirm the relative differences in voltage.

Characteristic Sensor Output:

VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V

VTA1: Throttle Position No. 1

VTA2: Throttle Position No. 2


·

If DTC P0121 is output, proceed to "Check Harness And Connector (Throttle Position Sensor - ECM)".





A

2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)

B

5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
a.

Disconnect the throttle with motor body assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D41-5 (VC) - D1-96 (VCTA) Always Below 1 Ω
D41-6 (VTA) - D1-98 (VTA1) Always Below 1 Ω
D41-4 (VTA2) - D1-99 (VTA2) Always Below 1 Ω
D41-3 (E2) - D1-97 (ETA) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
D41-5 (VC) or D1-96 (VCTA) - Body ground Always 10 kΩ or higher
D41-6 (VTA) or D1-98 (VTA1) - Body ground Always 10 kΩ or higher
D41-4 (VTA2) or D1-99 (VTA2) - Body ground Always 10 kΩ or higher




OK

3.INSPECT ECM (VC VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (VC VOLTAGE)
a.
U188260E01
0.83,1.051 1.607,1.303 false 2.747,1.051 1.969,1.303 false 0.074,0.054 2.155,0.219 2.081,0.165 10 Wire Harness Side Front View: 0.767,0.537 2.358,0.702 1.591,0.165 10 Throttle Body Connector 1.321,1.677 2.021,1.843 0.699,0.166 10 Front View 0.568,0.957 0.797,1.122 0.229,0.166 10 E2 2.799,0.957 3.028,1.122 0.229,0.166 10 VC 0.241,0.552 0.523,0.690 0.282,0.138 10 D41

Disconnect the throttle with motor body assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D41-5 (VC) - D41-3 (E2) Engine switch on (IG) 4.5 to 5.5 V




OK

4.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY

NG

4.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY
a.

Replace the throttle with motor body assembly (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>THROTTLE BODY>REMOVAL).



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester on.



d.

Turn the engine switch off and wait for at least 30 seconds.


e.

Start the engine.


f.

With the vehicle stationary, fully depress and released the accelerator pedal.


g.

Idle the engine for 2 seconds or more.


h.

Enter the following menus: Powertrain / Engine / DTC.


i.

Read the DTCs.

Result
Result Proceed to
DTC P0120, P0121, P0122, P0123, P0220, P0222, P0223, and/or P2135 are output A
DTC is not output B



A

B

END