The ECM constantly uses 5 V from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.
When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that receive power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.
Under normal conditions, the MIL is illuminated when the engine switch is turned on (IG). The MIL goes off when the engine is started.
Check that the Malfunction Indicator Lamp (MIL) lights up when turning the engine switch on (IG).
MIL lights up.
NG
OK
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester on.
Check the communication between the tester and ECM.
| Result | Proceed to |
|---|---|
| Communication is possible | A |
| Communication is not possible | B |
B
A
Disconnect the throttle with motor body assembly connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
B
A
Disconnect the accelerator pedal position sensor connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
B
A
Disconnect the battery current sensor connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
B
A
Disconnect the VVT sensor for intake camshaft bank 1 connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
B
A
Disconnect the VVT sensor for exhaust camshaft bank 1 connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
B
A
Disconnect the VVT sensor for intake camshaft bank 2 connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
B
A
Disconnect the VVT sensor for exhaust camshaft bank 2 connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
B
A
Disconnect the throttle with motor body assembly connector.
Disconnect the accelerator pedal position sensor connector.
Disconnect the VVT sensor for intake camshaft bank 1 connector.
Disconnect the VVT sensor for exhaust camshaft bank 1 connector.
Disconnect the VVT sensor for intake camshaft bank 2 connector.
Disconnect the VVT sensor for exhaust camshaft bank 2 connector.
Disconnect the battery current sensor connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D1-80 (VCIB) - Body ground | Always | 10 kΩ or higher |
| D1-96 (VCTA) - Body ground | Always | 10 kΩ or higher |
| D1-115 (VCV1) - Body ground | Always | 10 kΩ or higher |
| D1-113 (VCV2) - Body ground | Always | 10 kΩ or higher |
| D1-114 (VCE1) - Body ground | Always | 10 kΩ or higher |
| D1-112 (VCE2) - Body ground | Always | 10 kΩ or higher |
| A7-57 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A7-58 (VCP2) - Body ground | Always | 10 kΩ or higher |
OK
NG