A flat type knock control sensor (non-resonant type) has a structure that can detect vibration between approximately 5 kHz and 15 kHz.
The knock control sensors are fitted onto the engine block to detect engine knocking.
The knock control sensor contains a piezoelectric element which generates a voltage when it becomes deformed.
The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0327
P0332 |
Output voltage of knock sensor 1 or 2 is 0.5 V or less
(1 trip detection logic) |
·
Short in knock sensor 1 or 2 circuit ·
Knock sensor 1 or 2 ·
ECM |
| P0328
P0333 |
Output voltage of knock sensor 1 or 2 is 4.5 V or more
(1 trip detection logic) |
·
Open in knock sensor 1 or 2 circuit ·
Knock sensor 1 or 2 ·
ECM |
When any of DTCs P0327, P0328, P0332 and P0333 are set, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the engine switch is turned off.
Reference: Inspection using an oscilloscope
The correct waveform is as shown.
| ECM Terminal Name | Between KNK1 and EKNK, or KNK2 and EKN2 |
| Tester Range | 1 V/DIV., 1 ms./DIV. |
| Condition | Engine speed maintained at 4000 rpm after warming up engine |
DTCs P0327 and P0328 are for the bank 1 knock control sensor circuit.
DTCs P0332 and P0333 are for the bank 2 knock control sensor circuit.
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Data List / All Data / Knock Feedback Value.
Read the value while driving the vehicle.
The value changes.
| Malfunction does not occur | Knock Feedback Value changes |
| Malfunctions occur | Knock Feedback Value does not change |
The Knock Feedback Value change can be confirmed by running the engine with a high load, for example, by activating the air conditioning system and racing the engine.
OK
NG
Disconnect the DU1 connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| DU1 female connector 2 - 1 | Engine switch on (IG) | 4.5 to 5.5 V |
| DU1 female connector 4 - 3 | Engine switch on (IG) | 4.5 to 5.5 V |
OK
NG
Inspect the knock control sensor (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>KNOCK SENSOR>INSPECTION).
OK
NG
Disconnect the DU1 connector.
Disconnect the knock sensor connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| DU1 male connector 2 - U2-2 | Always | Below 1 Ω |
| DU1 male connector 1 - U2-1 | Always | Below 1 Ω |
| DU1 male connector 4 - U1-2 | Always | Below 1 Ω |
| DU1 male connector 3 - U1-1 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| DU1 male connector 2 or U2-2 - Body ground | Always | 10 kΩ or higher |
| DU1 male connector 1 or U2-1 - Body ground | Always | 10 kΩ or higher |
| DU1 male connector 4 or U1-2 - Body ground | Always | 10 kΩ or higher |
| DU1 male connector 3 or U1-1 - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the DU1 connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| DU1 male connector 2 - D1-95 (KNK1) | Always | Below 1 Ω |
| DU1 male connector 1 - D1-94 (EKNK) | Always | Below 1 Ω |
| DU1 male connector 4 - D1-118 (KNK2) | Always | Below 1 Ω |
| DU1 male connector 3 - D1-117 (EKN2) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| DU1 male connector 2 or D1-95 (KNK1) - Body ground | Always | 10 kΩ or higher |
| DU1 male connector 1 or D1-94 (EKNK) - Body ground | Always | 10 kΩ or higher |
| DU1 male connector 4 or D1-118 (KNK2) - Body ground | Always | 10 kΩ or higher |
| DU1 male connector 3 or D1-117 (EKN2) - Body ground | Always | 10 kΩ or higher |
OK
NG