Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0443  Evaporative Emission Control System Purge Control Valve Circuit  


DESCRIPTION

To reduce hydrocarbon (HC) emissions, evaporated fuel from the fuel tank is routed through a canister to the intake air surge tank assembly for combustion in the cylinders.

The ECM changes the duty signals to the purge VSV so that the intake amount of hydrocarbon (HC) emissions is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No. DTC Detection Condition Trouble Area
P0443 Terminal voltage of ECM output circuit does not correspond with drive signals from ECM to purge VSV
(1 trip detection logic)
·

Open or short in purge VSV circuit

·

Purge VSV

·

ECM



WIRING DIAGRAM

A159617E04
5.495,1.071 5.725,1.237 0.230,0.165 10 D1 5.819,1.071 6.166,1.237 0.346,0.165 10 PRG 5.474,0.899 5.746,1.064 0.272,0.165 10 108 5.503,1.601 5.718,1.766 0.215,0.165 10 A7 5.819,1.601 6.223,1.766 0.403,0.165 10 MREL 6.09,2.624 6.444,2.789 0.354,0.165 10 ECM 4.11,1.309 5.182,1.455 1.072,0.146 10 D50 Purge VSV 2.702,1.856 3.348,2.040 0.646,0.184 10 EFI MAIN 0.697,1.362 1.331,1.517 0.634,0.155 10 F/B BATT 0.697,1.88 1.303,2.068 0.606,0.188 10 FL MAIN 0.82,2.568 1.318,2.744 0.498,0.176 10 Battery 1.529,1.235 1.834,1.432 0.305,0.198 10 EFI 5.51,1.428 5.710,1.593 0.200,0.165 10 44 3.421,0.975 3.529,1.140 0.108,0.165 10 3 4.251,0.975 4.359,1.140 0.108,0.165 10 1 4.878,0.975 4.986,1.140 0.108,0.165 10 2 3.421,1.51 3.564,1.675 0.143,0.165 10 1 2.527,0.975 2.702,1.140 0.175,0.165 10 5 2.527,1.51 2.702,1.675 0.175,0.165 10 2 5.505,2.057 5.716,2.222 0.211,0.165 10 D1 5.819,2.057 6.026,2.222 0.207,0.165 10 E1 5.522,1.884 5.699,2.049 0.177,0.165 10 81

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EVAP CONTROL)
a.
A159587E01
0.26,0.26 0.971,0.421 0.711,0.161 10 VSV is ON 1.978,0.26 2.745,0.421 0.767,0.161 10 VSV is OFF

Connect the intelligent tester to the DLC3.


b.

Remove the vacuum hose of the purge VSV from the charcoal canister.


c.

Start the engine and turn the tester ON.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Evap Control.


e.

When the purge VSV is operated using the intelligent tester, check whether the disconnected hose applies suction to your finger.

OK:
Tester Operation Specified Condition
VSV is ON Disconnected hose applies suction to finger
VSV is OFF Disconnected hose applies no suction to finger




OK

NG

2.INSPECT PURGE VSV
2.INSPECT PURGE VSV

OK

3.INSPECT PURGE VSV (POWER SOURCE VOLTAGE)

NG

REPLACE PURGE VSV

3.INSPECT PURGE VSV (POWER SOURCE VOLTAGE)
a.
U188263E02
1.333,1.719 2.052,1.917 0.719,0.198 10 false Front View 0.802,0.49 2.24,0.688 1.438,0.198 10 false Purge VSV Connector 0.052,0.052 1.354,0.25 1.302,0.198 10 false Wire Harness Side: 0.854,1.229 1.063,1.406 0.208,0.177 10 false D9

Disconnect the purge VSV connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage between the terminal of the wire harness side connector and body ground.

Standard voltage:
Tester Connection Condition Specified Condition
D50-2 - Body ground Engine switch on (IG) 11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI MAIN RELAY - PURGE VSV)

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Disconnect the purge VSV connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance between the wire harness side connectors.

Standard resistance (Check for open):
Tester Connection Condition Specified Condition
D50-2 - D1-108 (PRG) Always Below 1 Ω


Standard resistance (Check for short):
Tester Connection Condition Specified Condition
D50-2 or D1-108 (PRG) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR