Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › 2013.04–2016.05
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0504  Brake Switch "A" / "B" Correlation  P0724  Brake Switch "B" Circuit High  


DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the intelligent tester, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.



DTC No. DTC Detection Condition Trouble Area
P0504 Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):
(a) Engine switch on (IG)
(b) Brake pedal released
(c) STP signal OFF when ST1- signal OFF
·

Open or short in stop light switch assembly signal circuit

·

Stop light switch

·

ECM


P0724 The stop light switch assembly remains on even when the vehicle repeats 5 cycles of STOP (less than 3 km/h [1.86 mph]) and GO (30 km/h [18.65 mph] or more) (2 trip detection logic).
·

Short in stop light switch signal circuit

·

Stop light switch assembly

·

ECM



WIRING DIAGRAM

A159618E06
5.792,2.354 6.031,2.531 0.24,0.177 10 false A7 6.115,2.292 6.552,2.469 0.438,0.177 10 false ST1- 6.333,6.833 6.771,7.01 0.438,0.177 10 false ECM 5.792,2.865 6.031,3.042 0.24,0.177 10 false A7 5.792,2.156 6.031,2.333 0.24,0.177 10 false 35 5.792,2.677 6.031,2.854 0.24,0.177 10 false 36 6.115,2.729 6.552,2.906 0.438,0.177 10 false STP 5.792,5.938 6.031,6.115 0.24,0.177 10 false D1 5.802,5.75 6.094,5.927 0.292,0.177 10 false 81 6.115,5.896 6.344,6.073 0.229,0.177 10 false E1 3.635,3.177 5.688,3.354 2.052,0.177 10 false A33 Stop Light Switch Assembly 0.26,1.51 1.573,1.688 1.313,0.177 10 false G58 Main Body ECU 1.969,3.146 2.313,3.323 0.344,0.177 10 false IG2 3.156,2.458 3.5,2.635 0.344,0.177 10 false IGN 3.677,4.031 4.167,4.208 0.49,0.177 10 false STOP 1.844,5.094 2.281,5.271 0.438,0.177 10 false ALT 2.438,5.083 3.365,5.26 0.927,0.177 10 false RH-MAIN-JB 4.885,2.198 5.135,2.375 0.25,0.177 10 false 3 1.448,0.875 1.698,1.052 0.25,0.177 10 false 11 1,0.969 1.479,1.146 0.479,0.177 10 false IG2D 4.052,2.198 4.188,2.375 0.135,0.177 10 false 4 4.052,2.729 4.302,2.906 0.25,0.177 10 false 2 4.885,2.729 5.135,2.906 0.25,0.177 10 false 1 2.427,2.198 2.677,2.375 0.25,0.177 10 false 3 1.646,2.198 1.896,2.375 0.25,0.177 10 false 5 2.427,2.729 2.677,2.906 0.25,0.177 10 false 1 1.646,2.729 1.896,2.906 0.25,0.177 10 false 2 0.792,4.042 1.427,4.219 0.635,0.177 10 false F/B BATT 0.792,5.646 1.417,5.823 0.625,0.177 10 false FL MAIN 0.792,3.219 1.073,3.396 0.281,0.177 10 false IG2 0.885,6.365 1.375,6.542 0.49,0.177 10 false Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Stop light switch assembly conditions can be checked using the intelligent tester.

(a)

Connect the intelligent tester to the DLC3.

(b)

Turn the engine switch on (IG).

(c)

Turn the tester on.

(d)

Enter the following menus: Powertrain / Engine / Data List / All Data / Stop Light Switch and ST1.

(e)

Check the Data List indication when the brake pedal is depressed and released.

Brake Pedal Operation Stop Light Switch ST1
Depressed ON ON
Released OFF OFF


·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.



PROCEDURE

1.CHECK STOP LIGHT (OPERATION OF STOP LIGHT)
a.

Check whether the stop lights turn on and off normally when the brake pedal is depressed and released.

OK:

Stop lights turn ON when brake pedal is depressed.




OK

2.READ VALUE USING INTELLIGENT TESTER (STP SIGNAL AND ST1-)

NG

REPAIR OR REPLACE STOP LIGHT SWITCH ASSEMBLY CIRCUIT

2.READ VALUE USING INTELLIGENT TESTER (STP SIGNAL AND ST1-)
a.
FI07052E73
0.406,1.74 1.104,1.906 0.698,0.167 10 false Depressed 2.281,1.74 2.906,1.917 0.625,0.177 10 false Released

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Data List / All Data / Stop Light Switch and ST1.


d.

Check the STP signal when the brake pedal is depressed and released.

OK:
Brake Pedal Operation Specified Condition
Depressed STP and ST1 signal ON
Released STP and ST1 signal OFF




NG

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly (See page Vehicle Interior>LIGHTING>STOP LIGHT SWITCH>INSPECTION).



OK

4.CHECK ECM (STP, ST1- VOLTAGE)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.CHECK ECM (STP, ST1- VOLTAGE)
a.
U188274E02
1.875,3.677 2.208,4.208 false 1.781,3.677 1.375,4.219 false 1.781,0 2.583,0.313 0.802,0.313 10 false Brake Pedal Released 0.229,0 1,0.323 0.771,0.323 10 false Brake Pedal Depressed 0.073,2.104 1.375,2.281 1.302,0.177 10 false Wire Harness Side: 1.167,2.552 2.177,2.729 1.01,0.177 10 false ECM Connector 2.563,3.354 3.26,3.51 0.698,0.156 10 false Front View 2.052,4.229 2.375,4.406 0.323,0.177 10 false STP 1.135,4.219 1.5,4.396 0.365,0.177 10 false ST1- 0.75,2.635 0.948,2.781 0.198,0.146 10 false A7

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Operation Specified Condition
A7-36 (STP) - Body ground Depressed 7.5 to 14 V
A7-36 (STP) - Body ground Released 0 to 3 V
A7-35 (ST1-) - Body ground Depressed 0 to 3 V
A7-35 (ST1-) - Body ground Released 7.5 to 14 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR