Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If both signals, which indicate whether the brake pedal is being depressed or released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and sets the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the GTS, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.



DTC No. DTC Detection Condition Trouble Area
P0504 Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):
(a) Engine switch on (IG)
(b) Brake pedal released
(c) STP signal OFF when ST1- signal OFF
·

Open or short in stop light switch assembly signal circuit

·

Stop light switch assembly

·

ECM



WIRING DIAGRAM

A385875E04
5.792,2.333 6.031,2.51 0.24,0.177 10 false A7 6.115,2.302 6.552,2.479 0.438,0.177 10 false ST1- 6.333,6.823 6.771,7 0.438,0.177 10 false ECM 5.792,2.75 6.031,2.927 0.24,0.177 10 false A7 5.792,2.125 6.031,2.302 0.24,0.177 10 false 35 5.792,2.563 6.031,2.74 0.24,0.177 10 false 36 6.115,2.615 6.552,2.792 0.438,0.177 10 false STP 5.792,5.927 6.031,6.104 0.24,0.177 10 false D1 5.802,5.729 6.094,5.906 0.292,0.177 10 false 81 6.115,5.906 6.344,6.083 0.229,0.177 10 false E1 4.135,3.406 5.229,3.781 1.094,0.375 10 false Stop Light Switch Assembly 0.26,1.51 0.604,1.688 0.344,0.177 10 false G58 1.969,3.135 2.313,3.313 0.344,0.177 10 false IG2 3.156,2.469 3.5,2.646 0.344,0.177 10 false IGN 3.677,4.271 4.167,4.448 0.49,0.177 10 false STOP 1.844,5.094 2.281,5.271 0.438,0.177 10 false ALT 2.438,5.104 3.531,5.406 1.094,0.302 10 false RH-MAIN-JB 4.875,2.219 5.125,2.396 0.25,0.177 10 false 4 1.448,0.885 1.698,1.063 0.25,0.177 10 false 11 1,0.979 1.479,1.156 0.479,0.177 10 false IG2D 4.052,2.219 4.188,2.396 0.135,0.177 10 false 5 4.052,2.646 4.208,2.823 0.156,0.177 10 false 1 4.875,2.615 5.125,2.792 0.25,0.177 10 false 2 2.417,2.219 2.667,2.396 0.25,0.177 10 false 3 1.646,2.219 1.896,2.396 0.25,0.177 10 false 5 2.417,2.74 2.667,2.917 0.25,0.177 10 false 1 1.646,2.74 1.896,2.917 0.25,0.177 10 false 2 0.792,4.052 1.427,4.229 0.635,0.177 10 false F/B BATT 0.792,5.656 1.417,5.833 0.625,0.177 10 false FL MAIN 0.792,3.229 1.073,3.406 0.281,0.177 10 false IG2 0.885,6.375 1.375,6.552 0.49,0.177 10 false Battery 0.573,1.51 1.885,1.688 1.313,0.177 10 false Main Body ECU 3.844,3.406 4.125,3.583 0.281,0.177 10 false A37 4.875,3 5.125,3.177 0.25,0.177 10 false 3 4.229,2.74 4.479,2.917 0.25,0.177 10 false B 4.229,2.302 4.479,2.479 0.25,0.177 10 false B 4.719,2.292 4.854,2.469 0.135,0.177 10 false L 4.521,2.719 4.865,2.896 0.344,0.177 10 false OUT 4.5,3.083 4.844,3.26 0.344,0.177 10 false GND

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Stop light switch assembly conditions can be checked using the GTS.

(a)

Connect the GTS to the DLC3.

(b)

Turn the engine switch on (IG).

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine / Data List / All Data / Stop Light Switch and ST1.

(e)

Check the Data List indication when the brake pedal is depressed and released.

Brake Pedal Operation Stop Light Switch ST1
Depressed ON ON
Released OFF OFF




PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
a.
U188531E02
1.333,1.24 1.01,1.573 false 0.125,0.01 0.427,0.292 0.302,0.281 10 false *a 0.604,1.063 0.927,1.302 0.323,0.24 10 false A37 0.927,1.594 1.094,1.802 0.167,0.208 10 false B

Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-1 (B) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY)

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
a.
U188532E02
2.104,1.229 2.427,1.563 false 0.125,0.01 0.427,0.292 0.302,0.281 10 false *a 0.604,1.063 0.927,1.302 0.323,0.24 10 false A37 2.406,1.594 2.573,1.802 0.167,0.208 10 false B

Disconnect the stop light switch assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-5 (B) - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - IG2 RELAY)

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A37-3 (GND) - Body ground Always Below 1 Ω




OK

4.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)
a.

Disconnect the ECM connector.

U188533E02
5.917,1.552 5.458,2.01 false 5.979,1.552 6.271,2.021 false 1.229,1.917 1.531,2.156 0.302,0.24 10 false *a 3.01,1.917 3.313,2.156 0.302,0.24 10 false *b 4.635,0.469 4.885,0.688 0.25,0.219 10 false *c 4.677,1.385 5.042,1.76 0.365,0.375 10 false A7 5.281,2.021 5.646,2.198 0.365,0.177 10 false ST1- 6.167,2.021 6.469,2.198 0.302,0.177 10 false STP


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Operation Specified Condition
A7-35 (ST1-) - Body ground Brake pedal released 7.5 to 14 V
Brake pedal depressed Below 1.5 V
A7-36 (STP) - Body ground Brake pedal released Below 1.5 V
Brake pedal depressed 7.5 to 14 V


Text in Illustration
*a Brake Pedal Depressed *b Brake Pedal Released
*c Front view of wire harness connector
(to ECM)
- -



OK

NG

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A37-4 (L) - A7-35 (ST1-) Always Below 1 Ω
A37-2 (OUT) - A7-36 (STP) Always Below 1 Ω
A37-4 (L) or A7-35 (ST1-) - Body ground Always 10 kΩ or higher
A37-2 (OUT) or A7-36 (STP) - Body ground Always 10 kΩ or higher




OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR