Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P2102  Throttle Actuator Control Motor Circuit Low  P2103  Throttle Actuator Control Motor Circuit High  


DESCRIPTION

The throttle actuator is operated by the ECM and opens and closes the throttle valve using gears.

The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle with motor body assembly. The throttle position sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to driver inputs.

HINT:

This Electronic Throttle Control System (ETCS) does not use a throttle cable.


DTC No. DTC Detection Condition Trouble Area
P2102 Both of the following conditions continue for 2.0 seconds (1 trip detection logic):
(a) The throttle actuator drive duty cycle is 80% or higher.
(b) The throttle actuator current is less than 0.2 A.
·

Open in throttle actuator circuit

·

Throttle actuator

·

ECM


P2103 Either of the following conditions is met (1 trip detection logic):
·

A hybrid IC diagnosis signal failure.

·

A hybrid IC high current limiter port failure.


·

Short in throttle actuator circuit

·

Throttle actuator

·

Throttle valve

·

Throttle with motor body assembly

·

ECM



FAIL-SAFE

When any of these DTCs or other DTCs relating to Electronic Throttle Control System (ETCS) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

Fail-safe mode continues until a pass condition is detected, and the engine switch is then turned off.

WIRING DIAGRAM

A112572E06
0.178,0.583 1.544,0.765 1.367,0.181 10 D41 Throttle Actuator 1.083,1.132 1.297,1.313 0.214,0.181 10 M+ 1.466,1.132 1.583,1.313 0.117,0.181 10 2 1.466,1.851 1.583,2.032 0.117,0.181 10 1 1.101,1.875 1.280,2.056 0.179,0.181 10 M- 2.672,0.523 3.229,0.704 0.558,0.181 10 Shielded 5.632,0.567 6.198,0.748 0.566,0.181 10 D1 ECM 4.915,1.118 5.129,1.299 0.214,0.181 10 M+ 4.593,1.118 4.806,1.299 0.214,0.181 10 19 4.593,1.865 4.806,2.046 0.214,0.181 10 18 4.593,2.622 4.806,2.803 0.214,0.181 10 41 4.915,1.854 5.094,2.035 0.179,0.181 10 M- 4.915,2.736 5.287,2.917 0.372,0.181 10 GE01 5.355,1.203 6.469,1.547 1.114,0.343 10 Throttle Actuator Control Circuit

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

The throttle actuator current (Throttle Motor Current) and the throttle actuator duty ratio (Throttle Motor Duty (Open) / Throttle Motor Duty (Close)) can be read using the intelligent tester. However, the ECM shuts off the throttle actuator current when the electronic throttle control system malfunctions.



PROCEDURE

1.INSPECT THROTTLE WTIH MOTOR BODY ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR)
a.

Inspect the throttle with motor body assembly (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>THROTTLE BODY>INSPECTION).



OK

2.CHECK HARNESS AND CONNECTOR (THROTTLE WITH MOTOR BODY ASSEMBLY - ECM)

NG

REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (THROTTLE WITH MOTOR BODY ASSEMBLY - ECM)
a.

Disconnect the throttle with motor body assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance (Check for open):
Tester Connection Condition Specified Condition
D41-2 (M+) - D1-19 (M+) Always Below 1 Ω
D41-1 (M-) - D1-18 (M-) Always Below 1 Ω


Standard resistance (Check for short):
Tester Connection Condition Specified Condition
D41-2 (M+) or D1-19 (M+) - Body ground Always 10 kΩ or higher
D41-1 (M-) or D1-18 (M-) - Body ground Always 10 kΩ or higher




OK

3.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
a.

Check for foreign objects between the throttle valve and the housing.

OK:

No foreign object between throttle valve and housing.




OK

4.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (THROTTLE VALVE)

NG

REPAIR REMOVE FOREIGN OBJECT AND CLEAN THROTTLE WITH MOTOR BODY ASSEMBLY

4.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (THROTTLE VALVE)
a.

Check if the throttle valve opens and closes smoothly.

OK:

Throttle valve opens and closes smoothly.




OK

NG

REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY