Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P2120  Throttle / Pedal Position Sensor / Switch "D" Circuit  P2122  Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input  P2123  Throttle / Pedal Position Sensor / Switch "D" Circuit High Input  P2125  Throttle / Pedal Position Sensor / Switch "E" Circuit  P2127  Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input  P2128  Throttle / Pedal Position Sensor / Switch "E" Circuit High Input  P2138  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  


DESCRIPTION

HINT:
·

This Electronic Throttle Control System (ETCS) does not use a throttle cable.

·

These DTCs relate to the accelerator pedal position sensor.



The accelerator pedal position sensor is built into the accelerator pedal sensor assembly and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type sensor and uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds. The voltage, which is applied to terminals VPA and VPA2 of the ECM, varies between 0.5 V and 4.5 V in proportion to the operating angle of the accelerator pedal (throttle valve). A signal from VPA indicates the actual accelerator pedal opening angle (throttle valve opening angle) and is used for engine control. A signal from VPA2 conveys the status of the VPA circuit and is used to check the accelerator pedal position sensor itself.

The ECM monitors the actual accelerator pedal opening angle (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.

A255815E65
4.333,2.042 4.208,1.958 false 4.323,2.198 4.208,2.146 false 4.344,2.24 4.219,2.333 false 4.333,2.406 4.219,2.521 false 4.344,2.917 4.219,2.917 false 4.354,3.125 4.208,3.125 false 0.844,2.875 0.552,3.281 false 1.063,2.198 1.323,1.365 false 4.333,1.833 3.844,0.938 false 1.323,1.365 1.417,1.365 false 1.063,2.563 0.927,1.823 false 0.927,1.823 0.854,1.823 false 0.552,3.802 1.708,4.135 1.156,0.333 10 false Accelerator Pedal Sensor Assembly 1.458,1.292 2.031,1.521 0.573,0.229 10 false Magnet 0.323,1.74 0.854,1.917 0.531,0.177 10 false IC No. 1 0.313,3.354 0.844,3.531 0.531,0.177 10 false IC No. 2 2.063,1.729 2.604,1.958 0.542,0.229 10 false VPA 2.063,2.063 2.542,2.302 0.479,0.24 10 false EPA 2.063,2.385 2.792,2.667 0.729,0.281 10 false VCPA 2.063,2.688 2.438,2.865 0.375,0.177 10 false VPA2 2.063,3 2.438,3.177 0.375,0.177 10 false EPA2 2.063,3.323 2.438,3.5 0.375,0.177 10 false VCP2 2.677,3.76 3,3.938 0.323,0.177 10 false ECM 4.271,1.542 4.427,1.719 0.156,0.177 10 false *1 5.865,1.542 6.021,1.719 0.156,0.177 10 false *2 3.917,1.833 4.208,2.01 0.292,0.177 10 false 4.55 3.844,2.042 4.208,2.219 0.365,0.177 10 false 3.988 3.917,2.26 4.208,2.438 0.292,0.177 10 false 3.75 3.854,2.448 4.219,2.625 0.365,0.177 10 false 3.188 3.969,2.823 4.198,3 0.229,0.177 10 false 1.6 3.99,3.042 4.292,3.24 0.302,0.198 10 false 0.8 4.406,3.354 4.698,3.531 0.292,0.177 10 false 0.29 4.26,3.594 4.417,3.771 0.156,0.177 10 false 0 5.781,3.594 6.073,3.771 0.292,0.177 10 false 15.9 4.677,3.583 5.604,3.823 0.927,0.24 10 false Usable Range 4.667,3.896 7.167,4.094 2.5,0.198 10 false Accelerator Pedal Angle (°) 4.344,4.656 6.625,4.833 2.281,0.177 10 false *1: Accelerator Pedal Fully Released 4.344,4.969 6.729,5.135 2.385,0.167 10 false *2: Accelerator Pedal Fully Depressed 2.146,0.813 3.844,1.167 1.698,0.354 10 false Accelerator Pedal Position Sensor Output Voltage (V) 6.396,1.844 7.01,2.042 0.615,0.198 10 false VPA2 6.417,2.281 6.875,2.479 0.458,0.198 10 false VPA

DTC No. DTC Detection Condition Trouble Area
P2120 VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic)
·

Accelerator pedal position sensor


·

ECM


P2122 VPA 0.4 V or less for 0.5 seconds or more when accelerator pedal depressed (1 trip detection logic)
·

Accelerator pedal position sensor


·

Open in VCPA circuit


·

Open or ground short in VPA circuit


·

ECM


P2123 VPA 4.8 V or more for 2.0 seconds or more
(1 trip detection logic)
·

Accelerator pedal position sensor


·

Open in EPA circuit


·

ECM


P2125 VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic)
·

Accelerator pedal position sensor


·

ECM


P2127 VPA2 1.2 V or less for 0.5 seconds or more when accelerator pedal depressed (1 trip detection logic)
·

Accelerator pedal position sensor


·

Open in VCP2 circuit


·

Open or ground short in VPA2 circuit


·

ECM


P2128 Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic):
(a) VPA2 4.8 V or more
(b) VPA between 0.4 V and 3.45 V
·

Accelerator pedal position sensor


·

Open in EPA2 circuit


·

ECM


P2138 Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic):
(a) Difference between VPA and VPA2 0.02 V or less
(b) VPA 0.4 V or less and VPA2 1.2 V or less
·

Short between VPA and VPA2 circuits


·

Accelerator pedal position sensor


·

ECM



HINT:

When any of these DTCs are output, check the accelerator pedal position sensor voltage using the intelligent tester. Enter the following menus: Powertrain / Engine / Data List / All Data / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.

Trouble Area Accelerator Pedal Fully Released Accelerator Pedal Fully Depressed
Accel Sensor Out No. 1 Accel Sensor Out No. 2 Accel Sensor Out No. 1 Accel Sensor Out No. 2
Open in VCP circuit 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V
Open or ground short in VPA circuit 0 to 0.2 V 1.2 to 2.0 V 0 to 0.2 V 3.4 to 4.75 V
Open or ground short in VPA2 circuit 0.5 to 1.1 V 0 to 0.2 V 2.6 to 4.5 V 0 to 0.2 V
Open in EPA circuit 4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V
Normal condition 0.5 to 1.1 V 1.2 to 2.0 V 2.6 to 4.5 V 3.4 to 4.75 V


HINT:

Accelerator pedal positions are expressed as voltages.


FAIL-SAFE

When DTC P2120, P2121, P2122, P2123, P2125, P2127, P2128 or P2138 is stored, the ECM enters fail-safe mode. If either of the 2 sensor circuits malfunctions, the ECM uses the remaining circuit to calculate the accelerator pedal position to allow the vehicle to continue driving. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.

Fail-safe mode continues until a pass condition is detected, and the engine switch is turned off.

WIRING DIAGRAM

A112573E53
0.167,0.313 2.344,0.531 2.177,0.219 10 false Accelerator Pedal Position Sensor 1.563,0.885 1.896,1.094 0.333,0.208 10 false VPA 2.01,0.74 2.146,0.948 0.135,0.208 10 false 6 2.01,1.177 2.146,1.385 0.135,0.208 10 false 5 2.01,1.604 2.146,1.813 0.135,0.208 10 false 4 2.01,2.031 2.146,2.24 0.135,0.208 10 false 3 2.01,2.438 2.146,2.646 0.135,0.208 10 false 2 2.01,2.885 2.146,3.094 0.135,0.208 10 false 1 5.281,0.74 5.469,0.948 0.188,0.208 10 false 55 5.281,1.177 5.469,1.385 0.188,0.208 10 false 59 5.281,1.604 5.469,1.813 0.188,0.208 10 false 57 5.281,2.031 5.469,2.24 0.188,0.208 10 false 56 5.281,2.438 5.469,2.646 0.188,0.208 10 false 60 5.281,2.885 5.469,3.094 0.188,0.208 10 false 58 0.167,0.115 0.406,0.323 0.24,0.208 10 false A3 1.563,1.313 1.896,1.521 0.333,0.208 10 false EPA 1.49,1.719 1.917,1.927 0.427,0.208 10 false VCPA 1.49,2.146 1.917,2.354 0.427,0.208 10 false VPA2 1.49,2.552 1.917,2.76 0.427,0.208 10 false EPA2 1.49,2.969 1.917,3.177 0.427,0.208 10 false VCP2 5.604,0.781 5.938,0.99 0.333,0.208 10 false VPA 5.604,1.448 5.917,1.656 0.313,0.208 10 false EPA 5.604,1.688 6.042,1.896 0.438,0.208 10 false VCPA 5.604,2.052 6,2.26 0.396,0.208 10 false VPA2 5.604,2.708 6,2.917 0.396,0.208 10 false EPA2 5.604,2.927 6.021,3.135 0.417,0.208 10 false VCP2 5.969,0.385 6.531,0.563 0.563,0.177 10 false A7 ECM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ACCEL SENSOR OUT)
a.
A208621E09
2.438,1.76 3.146,1.99 0.708,0.229 10 false Released 0.531,1.771 1.333,2 0.802,0.229 10 false Depressed

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.


e.

Read the value displayed on the tester.

Standard Voltage:
Accelerator Pedal Operation Accel Sensor Out No. 1 Accel Sensor Out No. 2
Fully Released 0.5 to 1.1 V 1.2 to 2.0 V
Fully Depressed 2.6 to 4.5 V 3.4 to 4.75 V




OK

NG

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A3-6 (VPA) - A7-55 (VPA) Always Below 1 Ω
A3-5 (EPA) - A7-59 (EPA) Always Below 1 Ω
A3-4 (VCPA) - A7-57 (VCPA) Always Below 1 Ω
A3-3 (VPA2) - A7-56 (VPA2) Always Below 1 Ω
A3-2 (EPA2) - A7-60 (EPA2) Always Below 1 Ω
A3-1 (VCP2) - A7-58 (VCP2) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A3-6 (VPA) or A7-55 (VPA) - Body ground Always 10 kΩ or higher
A3-4 (VCPA) or A7-57 (VCPA) - Body ground Always 10 kΩ or higher
A3-3 (VPA2) or A7-56 (VPA2) - Body ground Always 10 kΩ or higher
A3-1 (VCP2) or A7-58 (VCP2) - Body ground Always 10 kΩ or higher




OK

3.CHECK TERMINAL VOLTAGE (VCPA AND VCP2)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TERMINAL VOLTAGE (VCPA AND VCP2)
a.
U188283E01
0.056,0.03 1.349,0.197 1.293,0.167 10 Wire Harness Side: 0.914,0.543 2.614,0.902 1.700,0.359 10 Accelerator Pedal Position Sensor Connector 0.438,0.641 0.703,0.822 0.264,0.181 10 A3 1.778,2.518 2.178,2.686 0.400,0.167 10 VCPA 1.281,2.857 2.014,3.024 0.733,0.167 10 Front View 0.474,2.518 0.874,2.686 0.400,0.167 10 VCP2 2.427,2.518 2.749,2.686 0.323,0.167 10 EPA 1.134,2.518 1.544,2.686 0.409,0.167 10 EPA2 0.717,2.479 1.304,1.83 false 1.355,2.484 1.462,1.858 false 1.981,2.484 1.733,1.858 false 2.511,2.473 1.896,1.858 false

Disconnect the accelerator pedal position sensor connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A3-4 (VCPA) - A3-5 (EPA) Engine switch on (IG) 4.5 to 5.5 V
A3-1 (VCP2) - A3-2 (EPA2) Engine switch on (IG) 4.5 to 5.5 V




OK

4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

NG

4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
a.

Replace the accelerator pedal sensor assembly (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL).



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG) and turn the tester on.


g.

Fully depress and release the accelerator pedal.


h.

Check that 5 seconds or more have elapsed since the engine switch is turned on (IG).


i.

Enter the following menus: Powertrain / Engine / DTC.


j.

Read the DTCs.

Result
Result Proceed to
DTC P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138 are output A
DTC is not output B



A

B

END