The Variable Valve Timing (VVT) system adjusts the intake valve timing to improve driveability. The engine oil pressure turns the VVT controller to adjust the valve timing.
The camshaft timing oil control valve assembly is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0010 | Open or short in camshaft timing oil control valve assembly (for intake camshaft of bank 1) circuit (1 trip detection logic). | ·
Open or short in camshaft timing oil control valve assembly (for intake camshaft of bank 1) circuit ·
Camshaft timing oil control valve assembly (for intake camshaft of bank 1) ·
ECM |
| P0020 | Open or short in camshaft timing oil control valve assembly (for intake camshaft of bank 2) circuit (1 trip detection logic). | ·
Open or short in camshaft timing oil control valve assembly (for intake camshaft of bank 2) circuit ·
Camshaft timing oil control valve assembly (for intake camshaft of bank 2) ·
ECM |
If DTC P0010 is output, check the VVT system (for intake camshaft of bank 1) circuit.
If DTC P0020 is output, check the VVT system (for intake camshaft of bank 2) circuit.
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Clear the DTC after recording the freeze frame data and DTC (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG) and wait 5 seconds.
Turn the tester on.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0010 or P0020 is output | A |
| DTC is not output | B |
A
B
Inspect the camshaft timing oil control valve assembly (for intake camshaft) (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION).
OK
NG
Disconnect the camshaft timing oil control valve assembly (for intake camshaft) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D1-58 (OC1+) - D47-1 | Always | Below 1 Ω |
| D1-57 (OC1-) - D47-2 | Always | Below 1 Ω |
| D1-52 (OC2+) - D34-1 | Always | Below 1 Ω |
| D1-51 (OC2-) - D34-2 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D1-58 (OC1+) or D47-1 - Body ground | Always | 10 kΩ or higher |
| D1-57 (OC1-) or D47-2 - Body ground | Always | 10 kΩ or higher |
| D1-52 (OC2+) or D34-1 - Body ground | Always | 10 kΩ or higher |
| D1-51 (OC2-) or D34-2 - Body ground | Always | 10 kΩ or higher |
OK
NG