Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM J

2GR-FE ENGINE CONTROL  SFI SYSTEM  Cranking Holding Function Circuit  


DESCRIPTION

WIRING DIAGRAM

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester ON.


c.

Enter the following menus: Powertrain / Engine / Data List / Starter Signal.


d.

Check the result when the engine switch is turned on (IG).


e.

Check the result when the engine starts.

Standard:
Engine Switch Condition Tester Display (Starter Signal)
On (IG) OFF
Engine starts ON




NG

2.INSPECT ECM (STSW TERMINAL VOLTAGE)

OK

10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ST RELAY)
2.INSPECT ECM (STSW TERMINAL VOLTAGE)
a.
U188287E01
1.878,1.687 2.662,1.174 false 0.07,0.135 1.383,0.298 1.313,0.163 10 Wire Harness Side: 1.003,0.828 2.053,0.997 1.049,0.169 10 ECM Connector 1.282,2.54 1.993,2.679 0.711,0.139 10 Front View 0.588,0.829 0.784,1.010 0.197,0.181 10 A7 2.71,1.085 3.172,1.266 0.462,0.181 10 STSW

Disconnect the ECM connector.


b.

Check that the shift lever is in the P position.


c.

Measure the voltage between the ECM terminal and body ground when operating the engine switch to start cranking.

Standard voltage:
Tester Connection Condition Specified Condition
A7-14 (STSW) - Body ground Always 11 to 14 V




OK

3.INSPECT ECM (STAR OUTPUT VOLTAGE)

NG

5.CHECK HARNESS AND CONNECTOR (ECM - MAIN BODY ECU)
3.INSPECT ECM (STAR OUTPUT VOLTAGE)
a.
A395329E01
0.479,0.448 0.813,0.698 0.333,0.25 2.188,1.25 2.708,1.042 true 0.104,0.073 1.698,0.333 1.594,0.26 10 false Wire Harness Side: 0.563,0.479 1.115,0.74 0.552,0.26 10 false D4 0.896,0.479 2.615,0.781 1.719,0.302 10 false PNP Switch Connector 1.448,1.813 2.5,2.083 1.052,0.271 10 false Front View 2.75,0.948 3.302,1.208 0.552,0.26 10 false B

Disconnect the Park/Neutral Position (PNP) switch connector.


b.

Measure the voltage between the terminal of the PNP switch connector and body ground while cranking the engine.

Standard voltage:
Tester Connection Condition Specified Condition
D4-4 (B) - Body ground Engine switch on (IG) 11 to 14 V




OK

4.INSPECT PARK / NEUTRAL POSITION SWITCH ASSEMBLY

NG

6.INSPECT ST CUT RELAY
4.INSPECT PARK / NEUTRAL POSITION SWITCH ASSEMBLY

NG

OK

10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ST RELAY)
5.CHECK HARNESS AND CONNECTOR (ECM - MAIN BODY ECU)
a.

Disconnect the main body ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance.

Standard resistance (Check for open):
Tester Connection Condition Specified Condition
G60-4 (STSW) - A7-14 (STSW) Always Below 1 Ω


Standard resistance (Check for short):
Tester Connection Condition Specified Condition
G60-4 (STSW) - Body ground Always Below 1 Ω




OK

CHECK SMART ENTRY AND START SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT ST CUT RELAY
a.
B016200

Remove the ST CUT relay from the fusible link block.


b.

Measure the resistance.

Standard resistance:
Tester Connection Specified Condition
3 - 5 10 kΩ or higher
3 - 5 Below 1 Ω
(When battery voltage applied to terminals 1 and 2)




OK

7.INSPECT NO. 7 RELAY BLOCK (RELAY HOLDER TERMINAL VOLTAGE)

NG

REPLACE ST CUT RELAY

7.INSPECT NO. 7 RELAY BLOCK (RELAY HOLDER TERMINAL VOLTAGE)
a.
A137347E03
0.302,2.292 1.292,2.656 0.99,0.365 10 false ST CUT Relay Holder 0.49,0.438 1.698,0.625 1.208,0.188 10 false Fusible Link Block

Remove the ST CUT relay from the fusible link block.


b.

Turn the engine switch on (IG).


c.

Measure the voltage between the terminals of the ST CUT relay holder.

Standard voltage:
Tester Connection Condition Specified Condition
ST CUT relay holder terminal (1) - ST CUT relay holder terminal (2) Engine switch on (IG) 11 to 14 V



d.

Reinstall the relay.



OK

8.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - MAIN BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - MAIN BODY ECU)
a.

Remove the ST CUT relay from the fusible link block.


b.

Disconnect the PNP switch assembly connector.


c.

Disconnect the main body ECU connector.


d.

Disconnect the ECM connector.


e.

Measure the resistance.

Standard resistance (Check for open):
Tester Connection Condition Specified Condition
ST CUT relay holder terminal (3) - D1-63 (STAR) Always Below 1 Ω
ST CUT relay holder terminal (3) - G60-6 (STR2) Always Below 1 Ω
G57-8 (STR) - ST CUT relay holder terminal (5) Always Below 1 Ω
D4-4 (B) - ST CUT relay holder terminal (5) Always Below 1 Ω


Standard resistance (Check for short):
Tester Connection Condition Specified Condition
ST CUT relay holder terminal (3) - Body ground Always 10 kΩ or higher
ST CUT relay holder terminal (5) - Body ground Always 10 kΩ or higher




OK

9.INSPECT FUSIBLE LINK BLOCK (CHECK FOR SHORT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT FUSIBLE LINK BLOCK (CHECK FOR SHORT)
a.

Disconnect the ECM connector.


b.

Remove the ST CUT relay from the fusible link block.


c.

Measure the resistance between the terminals of the ST CUT relay holder.

Standard resistance (Check for short):
Tester Connection Condition Specified Condition
ST CUT relay holder terminal (3) - Body ground Always 10 kΩ or higher
ST CUT relay holder terminal (5) - Body ground Always 10 kΩ or higher




OK

NG

CHECK SMART ENTRY AND START SYSTEM

10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ST RELAY)
a.

Remove the ST relay from the engine room No. 1 relay block.


b.

Disconnect the PNP switch assembly connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance.

Standard resistance (Check for open):
Tester Connection Condition Specified Condition
D4-9 (L) - STA (A7-48) Always Below 1 Ω
D4-9 (L) - ST relay holder terminal (1) Always Below 1 Ω
ST relay holder terminal (2) - Body ground Always Below 1 Ω


Standard resistance (Check for short):
Tester Connection Condition Specified Condition
D4-9 (L) - Body ground Always 10 kΩ or higher




OK

11.INSPECT BATTERY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT BATTERY
a.

Check that the battery is not depleted.

OK:

Battery is not depleted.




OK

12.CHECK BATTERY TERMINAL

NG

REPLACE BATTERY

12.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded.




OK

CHECK AND REPLACE STARTER POWER SOURCE CIRCUIT

NG

REPAIR OR REPLACE BATTERY TERMINAL