Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

The cranking holding control system keeps energizing the ST relay after the ECM detects the starter signal (STSW signal) from the main body ECU until the ECM performs a judgment of "Engine started". Furthermore, the ECM outputs an accessory cut signal (ACCR signal) to the ACC relay during cranking to prevent flickering of the combination meter, clock, audio system, and so on.

When the ECM detects the STSW signal, the ECM outputs the starter relay drive signal (STAR signal) to the starter relay through the park/neutral position switch assembly, and then, the engine is cranked. When the ECM receives a stable engine speed signal (NE signal), more specifically, when the NE signal reaches a predetermined value, the ECM stops outputting the STAR signal. Also, the ECM monitors the ST relay operating conditions based on the STA terminal voltage status.

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.43 mph) or more for over 20 seconds.

A103821E89
3.188,4.563 2.719,4.677 false 4.677,4.104 4.906,3.802 false 0.25,1.125 1.5,1.521 1.25,0.396 10 false Starter Input Signal (STSW) 0.24,2 1.594,2.406 1.354,0.406 10 false Starter Output Signal (STAR) 0.25,2.958 1.635,3.552 1.385,0.594 10 false ACC (Accessory) Cut Input Signal (ACCR) (for start control) 0.25,4.281 1.594,4.646 1.344,0.365 10 false Engine Speed Signal (NE) 2.031,1.052 2.333,1.25 0.302,0.198 10 false ON 1.979,1.521 2.385,1.74 0.406,0.219 10 false OFF 2.01,1.958 2.313,2.156 0.302,0.198 10 false ON 1.979,2.417 2.385,2.635 0.406,0.219 10 false OFF 1.865,3.094 2.521,3.344 0.656,0.25 10 false ACC Cut 2,4.667 3.729,4.875 1.729,0.208 10 false Ignition Switch ST Position 2.927,5.073 3.875,5.302 0.948,0.229 10 false Elapsed Time 4.906,0.458 6.854,0.833 1.948,0.375 10 false Keeps cranking until the engine is judged to be firing 4.917,1.74 6.813,2.135 1.896,0.396 10 false When no cranking hold control is effected 4.917,2.802 6.688,3.146 1.771,0.344 10 false Prevents meters, clock, etc. from flickering 4.938,3.688 6.74,3.917 1.802,0.229 10 false Engine start threshold 4.625,4.25 6.604,4.948 1.979,0.698 10 false When the NE signal reaches a predetermined value, the ECM determines that the engine has started successfully 1.865,3.552 2.688,3.771 0.823,0.219 10 false No ACC Cut

DTC No. DTC Detection Condition Trouble Area
P0617 When all of the following conditions are met, and a (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic):

(a) The vehicle speed is 20 km/h (12.43 mph) or more.

(b) The engine speed is 1000 rpm or higher.

(c) The STA signal is on.


·

Park/Neutral position switch assembly

·

Cranking holding function circuit

·

ECM



WIRING DIAGRAM

A159622E05
5.497,1.884 5.704,2.053 0.207,0.170 10 A7 5.786,1.884 6.226,2.053 0.440,0.170 10 STSW 2.09,1.884 2.607,2.053 0.516,0.170 10 STSW 5.497,1.716 5.704,1.886 0.207,0.170 10 14 2.576,1.884 2.881,2.053 0.306,0.170 10 G60 2.668,1.716 2.875,1.886 0.207,0.170 10 4 2.17,1.547 2.686,1.717 0.516,0.170 10 IG2D 2.576,1.547 2.881,1.717 0.306,0.170 10 G58 2.635,1.38 2.842,1.549 0.207,0.170 10 11 5.497,2.26 5.704,2.429 0.207,0.170 10 A7 5.786,2.26 6.212,2.429 0.426,0.170 10 ACCR 2.1,2.26 2.616,2.429 0.516,0.170 10 ACCR 5.497,2.092 5.704,2.262 0.207,0.170 10 13 2.571,2.26 2.852,2.429 0.281,0.170 10 G58 2.66,2.092 2.867,2.262 0.207,0.170 10 3 5.497,2.605 5.704,2.775 0.207,0.170 10 D1 5.786,2.605 6.185,2.775 0.398,0.170 10 STAR 4.696,3.086 5.247,3.256 0.551,0.170 10 ST CUT 2.875,6.267 3.086,6.436 0.211,0.170 10 ST 6.006,5.931 6.356,6.101 0.350,0.170 10 ECM 2.378,4.312 3.962,4.633 1.585,0.321 10 D4 Park/Neutral Position Switch Assembly 1.621,3.358 2.753,3.706 1.132,0.347 10 Main Body ECU 0.9,5.88 1.400,6.041 0.500,0.161 10 Battery 0.794,4.836 1.378,4.992 0.584,0.156 10 FL MAIN 2.013,0.738 2.277,0.885 0.264,0.147 10 IG2 3.505,1.201 3.770,1.356 0.264,0.156 10 IG2 1.719,4.836 2.004,5.184 0.285,0.347 10 ST 0.794,4.122 1.454,4.276 0.660,0.154 10 F/B BATT 3.795,6.118 4.307,6.277 0.511,0.159 10 Starter 2.146,2.605 2.663,2.775 0.516,0.170 10 STR2 5.497,2.438 5.704,2.607 0.207,0.170 10 63 5.497,5.035 5.704,5.204 0.207,0.170 10 A7 5.786,5.035 6.303,5.204 0.516,0.170 10 STA 5.497,4.867 5.704,5.037 0.207,0.170 10 48 4.482,2.708 4.688,2.878 0.207,0.170 10 2 4.482,3.531 4.688,3.700 0.207,0.170 10 1 2.506,5.506 2.713,5.676 0.207,0.170 10 1 2.506,5.8 2.713,5.970 0.207,0.170 10 5 3.346,5.506 3.553,5.676 0.207,0.170 10 2 3.346,5.8 3.553,5.970 0.207,0.170 10 3 3.902,2.708 4.109,2.878 0.207,0.170 10 3 3.97,0.467 4.177,0.637 0.207,0.170 10 3 3.97,0.775 4.177,0.945 0.207,0.170 10 1 3.179,0.467 3.386,0.637 0.207,0.170 10 5 3.179,0.775 3.386,0.945 0.207,0.170 10 2 3.902,3.531 4.109,3.700 0.207,0.170 10 5 2.522,3.927 2.729,4.097 0.207,0.170 10 9 3.328,3.927 3.535,4.097 0.207,0.170 10 4 2.571,2.605 2.852,2.775 0.281,0.170 10 G60 2.66,2.438 2.867,2.607 0.207,0.170 10 6 2.207,2.979 2.724,3.149 0.516,0.170 10 STR 2.571,2.979 2.852,3.149 0.281,0.170 10 G57 2.66,2.811 2.867,2.981 0.207,0.170 10 8 2.67,3.927 2.790,4.097 0.121,0.170 10 L 3.156,3.927 3.277,4.097 0.121,0.170 10 B

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Starter Signal.


e.

Check the value displayed on the tester when the vehicle is driven at 20 km/h (12.4 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


Result
Condition Tester Display Proceed to
Driving at 20 km/h (12.4 mph) or more OFF A
ON B



A

B

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly (See page Drivetrain>U660E (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).



OK

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace harness or connector (park/neutral position switch assembly - ST relay - ECM).



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Drive the vehicle at 20 km/h (12 mph) or more for 20 seconds or more.


g.

Enter the following menus: Powertrain / Engine / DTC.


h.

Read the DTCs.

Result
Result Proceed to
DTC is not output A
DTC P0617 is output B



A

END

B