Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P1550  Battery Current Sensor Circuit  P1551  Battery Current Sensor Circuit Low  P1552  Battery Current Sensor Circuit High  


DESCRIPTION

A110645E01
0.167,0.454 1.977,0.668 1.810,0.214 10 Sensor Output Voltage 0.078,1.117 0.350,1.318 0.272,0.201 10 (V) 3.103,2.499 3.408,2.700 0.304,0.201 10 (A) 1.424,2.666 2.069,2.880 0.646,0.214 10 Current

The battery current sensor installed on the positive (+) battery terminal detects the amount of current supplied from the generator.

The battery current sensor changes current to voltage (at the positive (+) battery terminal) and sends it to the ECM. The ECM controls the voltage of the generator based on the signals from the battery current sensor.

DTC No. DTC Detection Condition Trouble Area
P1550 The following condition continues for 10 seconds or more with the engine switch on (IG) (1 trip detection logic):
·

Difference between the maximum and minimum current values of the battery current sensor is 1 A or less


·

Open or short in battery current sensor circuit

·

Battery current sensor

·

ECM


P1551 Battery current sensor output value is 0.2 V or less for 0.5 seconds or more with the engine switch on (IG) (1 trip detection logic):
·

Short in battery current sensor circuit

·

Battery current sensor

·

ECM


P1552 Battery current sensor output value is 4.8 V or more for 0.5 seconds or more with the engine switch on (IG) (1 trip detection logic):
·

Open in battery current sensor circuit

·

Battery current sensor

·

ECM



WIRING DIAGRAM

A127777E02
1.109,0.545 2.784,0.732 1.675,0.186 10 A2 Battery Current Sensor 2.783,2.04 2.973,2.222 0.190,0.181 10 IB 2.648,1.43 2.997,1.611 0.349,0.181 10 VC5 3.045,1.43 3.168,1.611 0.123,0.181 10 2 3.045,2.053 3.168,2.234 0.123,0.181 10 3 3.045,2.66 3.168,2.842 0.123,0.181 10 4 3.045,3.246 3.168,3.427 0.123,0.181 10 1 2.69,3.098 2.985,3.279 0.295,0.181 10 THB 2.772,2.659 2.959,2.841 0.187,0.181 10 E2 5.35,1.54 5.738,1.700 0.387,0.161 10 VCIB 5.022,2.045 5.287,2.205 0.265,0.161 10 100 5.022,2.641 5.287,2.802 0.265,0.161 10 101 5.022,3.243 5.287,3.404 0.265,0.161 10 103 5.076,1.421 5.272,1.582 0.196,0.161 10 80 5.35,2.753 5.684,2.934 0.334,0.181 10 EIB 5.35,3.371 5.645,3.552 0.295,0.181 10 THB 5.35,2.139 5.540,2.320 0.190,0.181 10 IB 5.683,0.869 6.257,1.030 0.574,0.161 10 D1 ECM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.INSPECT BATTERY CURRENT SENSOR

OK

2.CHECK HARNESS AND CONNECTOR (BATTERY CURRENT SENSOR - ECM)

NG

REPLACE BATTERY CURRENT SENSOR

2.CHECK HARNESS AND CONNECTOR (BATTERY CURRENT SENSOR - ECM)
a.

Disconnect the battery current sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A2-3 (IB) - D1-100 (IB) Always Below 1 Ω
A2-2 (VC5) - D1-80 (VCIB) Always Below 1 Ω
A2-4 (E2) - D1-101 (EIB) Always Below 1 Ω
A2-1 (THB) - D1-103 (THB) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A2-3 (IB) or D1-100 (IB) - Body ground Always 10 kΩ or higher
A2-2 (VC5) or D1-80 (VCIB) - Body ground Always 10 kΩ or higher
A2-1 (THB) or D1-103 (THB) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR