Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › 2014.09–2016.05
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P1589  Acceleration Sensor Learning Value  


DESCRIPTION

The ECM stores a DTC if zero point calibration has not been done or completed successfully after replacing the ECM or yaw rate sensor.

The skid control ECU supplies power to the yaw rate sensor and records the sensor data. The data is shared by the ECM via CAN. Zero point calibration and operation is performed by each ECU.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P1589
1.

The vehicle speed is 2 km/h (1.2 mph) or more.

2.

The yaw rate sensor calibration (deceleration sensor zero point calibration) has not been completed.

3.

-

4.

1 trip detection logic


Yaw rate sensor calibration (deceleration sensor zero point calibration) has not been performed
1.

The yaw rate sensor calibration (deceleration sensor zero point calibration) is performed.

2.

The learned values of the yaw rate sensor calibration (deceleration sensor zero point calibration) are abnormal (out of normal range).

3.

-

4.

1 trip detection logic


·

Vehicle was not stabilized during the yaw rate sensor calibration (deceleration sensor zero point calibration)

·

Yaw rate sensor

·

ECM



WIRING DIAGRAM

PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P1589)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / DTC.


e.

Read the DTCs.


f.

Enter the following menus: Chassis / ABS/VSC/TRC / DTC.


g.

Read the DTCs.


h.

Check for DTCs of the CAN communication system (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

Result
Result Proceed to
DTC P1589 is output A
DTC P1589 and other DTCs (vehicle stability control system) are output B
DTC P1589 and other DTCs (CAN communication system) are output C

HINT:

Yaw rate sensor calibration (deceleration sensor zero point calibration) cannot be completed properly while communication with any of the following items is interrupted: yaw rate sensor, skid control ECU, ECM or TCM. Perform yaw rate sensor calibration (deceleration sensor zero point calibration) after repair.




A

2.INSPECT YAW RATE SENSOR

B

C

2.INSPECT YAW RATE SENSOR
a.

Check the yaw rate sensor for any inclination, bracket deformation or installation clearance.

OK:

The yaw rate sensor is installed correctly.




OK

3.PERFORM INITIALIZATION

NG

3.PERFORM INITIALIZATION
a.

Perform zero point calibration of the yaw rate sensor (deceleration sensor zero point calibration) (See page Drivetrain>U660E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>INITIALIZATION).



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P1589)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P1589)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Drive the vehicle.


f.

Enter the following menus: Powertrain / Engine / DTC.


g.

Read the DTCs.

Result
Result Proceed to
DTC is not output A
DTC P1589 is output B



A

END

B