These DTCs relate to the throttle position sensor.
The throttle position sensor is mounted on the throttle body assembly, and detects the opening angle of the throttle valve. This sensor is a non-contact type sensor. It uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds.
The throttle position sensor has 2 sensor circuits, VTA1 and VTA2 each of which transmits a signal. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 4.75 V in proportion to the throttle valve opening angle, and are transmitted to the VTA1 and VTA2 terminals of the ECM.
As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air fuel ratio correction, power increase correction and fuel-cut control.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0120 | The output voltage of VTA1 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds or more (1 trip detection logic). | ·
Throttle position sensor (built into throttle body assembly) ·
ECM |
| P0121 | The difference between the VTA1 and VTA2 voltages is less than 0.8 V, or higher than 1.6 V for 2 seconds (1 trip detection logic). | ·
Throttle position sensor (built into throttle body assembly) ·
Throttle position sensor circuit ·
ECM |
| P0122 | The output voltage of VTA1 is 0.2 V or less for 2 seconds or more (1 trip detection logic). | ·
Throttle position sensor (built into throttle body assembly) ·
Short in VTA1 circuit ·
Open in VCTA circuit ·
ECM |
| P0123 | The output voltage of VTA1 is 4.54 V or higher for 2 seconds or more (1 trip detection logic). | ·
Throttle position sensor (built into throttle body assembly) ·
Open in VTA1 circuit ·
Open in ETA circuit ·
Short between VCTA and VTA1 circuits ·
ECM |
| P0220 | The output voltage of VTA2 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds or more (1 trip detection logic). | ·
Throttle position sensor (built into throttle body assembly) ·
ECM |
| P0222 | The output voltage of VTA2 is 1.75 V or less for 2 seconds or more (1 trip detection logic). | ·
Throttle position sensor (built into throttle body assembly) ·
Short in VTA2 circuit ·
Open in VCTA circuit ·
ECM |
| P0223 | The output voltage of VTA2 is 4.8 V or higher, and VTA1 is between 0.2 V and 2.02 V for 2 seconds or more (1 trip detection logic). | ·
Throttle position sensor (built into throttle body assembly) ·
Open in VTA2 circuit ·
Open in ETA circuit ·
Short between VCTA and VTA2 circuits ·
ECM |
| P2135 | Either of the following conditions is met (1 trip detection logic):
(a) The difference between the output voltages of VTA1 and VTA2 is 0.02 V or less for 0.5 seconds or more. (b) The output voltage of VTA1 is 0.2 V or less, and VTA2 is 1.75 V or less for 0.4 seconds or more. |
·
Short between VTA1 and VTA2 circuits ·
Throttle position sensor (built into throttle body assembly) ·
ECM |
When any of these DTCs are output, check the throttle valve opening angle using the intelligent tester. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Position No. 1 and Throttle Position No. 2.
Throttle Position No. 1 is the VTA1 signal, and Throttle Position No. 2 is the VTA2 signal.
| Tester Display | Accelerator Pedal Fully Released | Accelerator Pedal Fully Depressed |
|---|---|---|
| Throttle Position No. 1 | 0.5 to 1.1 V | 3.2 to 4.8 V |
| Throttle Position No. 2 | 2.1 to 3.1 V | 4.6 to 4.98 V |
When any of these DTCs or other DTCs relating to Electronic Throttle Control System (ETCS) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 6.5° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal angle, to allow the vehicle to continue operating at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the engine switch is then turned off.
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Position No. 1 and Throttle Position No. 2.
Read the values displayed on the tester.
| When Accelerator Pedal Fully Released | When Accelerator Pedal Fully Depressed | Trouble Area | Proceed to | ||
|---|---|---|---|---|---|
| Throttle Position No. 1
(VTA1) |
Throttle Position No. 2
(VTA2) |
Throttle Position No. 1
(VTA1) |
Throttle Position No. 2
(VTA2) |
||
| 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | VCTA circuit open | A |
| 4.5 to 4.98 V | 4.5 to 4.98 V | 4.5 to 4.98 V | 4.5 to 4.98 V | ETA circuit open | |
| 0 to 0.2 V,
or 4.5 to 4.98 V |
2.1 to 3.1 V
(Fail-safe) |
0 to 0.2 V,
or 4.5 to 4.98 V |
2.1 to 3.1 V
(Fail-safe) |
VTA1 circuit open or ground short | |
| 0.6 to 1.4 V
(Fail-safe) |
0 to 0.2 V,
or 4.5 to 4.98 V |
0.6 to 1.4 V
(Fail-safe) |
0 to 0.2 V,
or 4.5 to 4.98 V |
VTA2 circuit open or ground short | |
| 0.5 to 1.1 V | 2.1 to 3.1 V | 3.2 to 4.8 V
(Not fail-safe) |
4.6 to 4.98 V
(Not fail-safe) |
Throttle position sensor circuit normal | B |
DTC P0121 is stored when the VTA1 and VTA2 output voltages are not consistent with the sensor characteristics. Therefore, check the freeze frame data when this DTC is stored. Use the following formula to confirm the relative differences in voltage.
VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V
VTA1: Throttle Position No. 1
VTA2: Throttle Position No. 2
If DTC P0121 is output, proceed to "Check Harness And Connector (Throttle Position Sensor - ECM)".
A
B
Disconnect the throttle body assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D41-5 (VC) - D2-67(VCTA ) | Always | Below 1 Ω |
| D41-6 (VTA) - D2-115 (VTA1) | ||
| D41-4 (VTA2) - D2-114 (VTA2) | ||
| D41-3 (E2) - D2-91 (ETA) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D41-5 (VC) or D2-67 (VCTA) - Body ground | Always | 10 kΩ or higher |
| D41-6 (VTA) or D2-115 (VTA1) - Body ground | ||
| D41-4 (VTA2) or D2-114 (VTA2) - Body ground |
OK
NG
Disconnect the throttle body assembly connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D41-5 (VC) - D41-3 (E2) | Engine switch on (IG) | 4.5 to 5.5 V |
OK
NG
Replace the throttle body assembly (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>THROTTLE BODY>REMOVAL).
NEXT
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester ON.
Clear DTCs (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off and wait for at least 30 seconds.
Start the engine.
Within the vehicle stationary, fully depress and released the accelerator pedal.
Idle the engine for 2 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Display (DTC Output) | Proceed to |
|---|---|
| P0120, P0121, P0122, P0123, P0220, P0222, P0223, and/or P2135 | A |
| No output | B |
A
B