Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › 2013.04–2014.09
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P0136  Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2)  P0137  Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2)  P0138  Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2)  


DESCRIPTION

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC (Three-Way Catalytic Converter) is used. For the most efficient use of the TWC, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric air fuel level. For the purpose of helping the ECM to deliver accurate air fuel ratio control, a heated oxygen sensor is used.

The heated oxygen sensor is located behind the TWC, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).

When the air fuel ratio becomes lean, the oxygen concentration in the exhaust gas is high. The heated oxygen sensor informs the ECM that the post-TWC air fuel ratio is lean (low voltage, i.e. less than 0.45 V).

Conversely, when the air fuel ratio is richer than the stoichiometric air fuel level, the oxygen concentration in the exhaust gas is low. The heated oxygen sensor informs the ECM that the post-TWC air fuel ratio is rich (high voltage, i.e. more than 0.45 V). The heated oxygen sensor has the property of changing its output voltage drastically when the air fuel ratio is close to the stoichiometric level.

The ECM uses the supplementary information from the heated oxygen sensor to determine whether the air fuel ratio after the TWC is rich or lean, and adjusts the fuel injection duration accordingly. Thus, if the heated oxygen sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air fuel ratio control.

A131740E14
3.094,1.396 3.396,1 false 2.802,1.906 3.427,1.906 false 2.719,2.531 3.375,2.5 true 2.74,2.802 3.375,2.969 false 1.135,3.031 1.448,3.031 false 2.792,1.573 2.781,1.646 false 2.833,1.75 3.417,1.385 3.417,1.385 2.771,1.604 true 1.573,0.885 2.583,1.083 1.01,0.198 10 false Atmospheric Air 3.438,0.896 4.177,1.094 0.74,0.198 10 false Housing 3.438,1.302 4.969,1.5 1.531,0.198 10 false Platinum Electrode 4.135,0.781 5.104,0.979 0.969,0.198 10 false Output Voltage 5.26,0.823 6.646,1.021 1.385,0.198 10 false Ideal Air-fuel Mixture 2.125,3.24 3.021,3.438 0.896,0.198 10 false Exhaust Gas 3.458,1.813 4.917,2.177 1.458,0.365 10 false Solid Electrolyte (Zirconia Element) 3.417,2.885 4.615,3.083 1.198,0.198 10 false Coating (Ceramic) 3.438,2.396 3.917,2.594 0.479,0.198 10 false Heater 1.49,2.927 1.927,3.135 0.438,0.208 10 false Cover 4.844,2.958 7.146,3.156 2.302,0.198 10 false Richer - Air-fuel Ratio - Leaner

DTC No. DTC Detection Condition Trouble Area
P0136 Abnormal voltage output:
During active air fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a) Heated oxygen sensor voltage does not increase to 0.69 V or higher.

(b) Heated oxygen sensor voltage does not decrease to less than 0.21 V.


·

Heated oxygen sensor (sensor 2) circuit

·

Heated oxygen sensor (sensor 2)

·

Air fuel ratio sensor (sensor 1)

·

Gas leak from exhaust system

·

Fuel injector

·

Fuel pressure

·

PCV valve and hose

·

Intake system


P0137 Low voltage (open):
During active air fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a) Heated oxygen sensor voltage output is less than 0.21 V.

(b) Target air fuel ratio is rich.


·

Heated oxygen sensor (sensor 2) circuit

·

Heated oxygen sensor (sensor 2)

·

Air fuel ratio sensor (sensor 1)

·

Gas leak from exhaust system


P0138 High voltage (short):
During active air fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a) Heated oxygen sensor voltage output is higher than 0.69 V.

(b) Target air fuel ratio is lean.


·

Heated oxygen sensor (sensor 2) circuit

·

Heated oxygen sensor (sensor 2)

·

Air fuel ratio sensor (sensor 1)

·

ECM



MONITOR DESCRIPTION

Active Air Fuel Ratio Control


The ECM usually performs air fuel ratio feedback control so that the air fuel ratio sensor output indicates a near stoichiometric air fuel level. This vehicle includes active air fuel ratio control in addition to regular air fuel ratio control. The ECM performs active air fuel ratio control to detect any deterioration in the Three-Way Catalytic Converter (TWC) and heated oxygen sensor malfunctions (refer to the diagram below).

Active air fuel ratio control is performed for approximately 15 to 20 seconds while driving with a warm engine. During active air fuel ratio control, the air fuel ratio is forcibly regulated to become lean or rich by the ECM. If the ECM detects a malfunction, a DTC is stored.


Abnormal Voltage Output of Heated Oxygen Sensor (DTC P0136)


While the ECM is performing active air fuel ratio control, the air fuel ratio is forcibly regulated to become rich or lean. If the sensor is not functioning properly, the voltage output variation is small. For example, when the heated oxygen sensor voltage does not decrease to less than 0.21 V and does not increase to higher than 0.69 V during active air fuel ratio control, the ECM determines that the sensor voltage output is abnormal and stores DTC P0136.

A395376E01
2.802,2.333 3.052,2.677 false 3.063,2.677 3.24,2.677 false 2.938,2.115 3.208,1.698 false 3.208,1.698 3.417,1.698 false 0.125,0.083 4.448,0.302 4.323,0.219 10 false Heated Oxygen Sensor Circuit Malfunction (P0136: Abnormal Voltage) 4.542,0.802 5.656,0.969 1.115,0.167 10 false 15 to 20 seconds 4.771,1.292 5.438,1.479 0.667,0.188 10 false Operation 0.083,1.354 1.76,1.563 1.677,0.208 10 false Active air fuel ratio control 0.135,2.542 2.042,2.75 1.906,0.208 10 false Heated oxygen sensor voltage 2.25,1.375 2.573,1.563 0.323,0.188 10 false OFF 2.135,2.146 2.635,2.344 0.5,0.198 10 false 0.69 V 2.146,2.896 2.646,3.094 0.5,0.198 10 false 0.21 V 3.469,1.615 3.99,1.792 0.521,0.177 10 false Normal 3.323,2.594 4.01,2.771 0.688,0.177 10 false Abnormal


Open or Short in Heated Oxygen Sensor Circuit (DTC P0137 or P0138)


During active air fuel ratio control, the ECM calculates the Oxygen Storage Capacity (OSC)* of the Three-Way Catalytic Converter (TWC) by forcibly regulating the air fuel ratio to become rich or lean. If the heated oxygen sensor has an open or short circuit, or the voltage output of the sensor noticeably decreases, the OSC indicated an extraordinarily high value. Even if the ECM attempts to continue regulating the air fuel ratio to become rich or lean, the heated oxygen sensor output does not change.

While performing active air fuel ratio control, when the target air fuel ratio is rich and the heated oxygen sensor voltage output is less than 0.21 V (lean), the ECM interprets this as an abnormally low sensor output voltage and stores DTC P0137. When the target air fuel ratio is lean and the voltage output is higher than 0.69 V (rich) during active air fuel ratio control, the ECM determines that the sensor voltage output is abnormally high and stores DTC P0138.

*: The TWC has the capability to store oxygen. The OSC and the emissions purification capacity of the TWC are mutually related. The ECM determines whether the catalyst has deteriorated based on the calculated OSC value (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>P0420).

A395377E01
4.24,2.063 4.427,1.74 false 4.427,1.74 4.594,1.74 false 5.302,2.406 5.458,1.781 false 5.458,1.781 5.656,1.781 false 5.781,3.802 5.938,4.073 false 5.635,3.021 5.813,2.604 false 5.813,2.604 6.052,2.604 false 5.74,6.573 5.927,6.094 false 5.927,6.094 6.115,6.094 false 0.135,0.135 3.781,0.354 3.646,0.219 10 false Heated Oxygen Sensor Circuit Low Voltage (P0137: Open) 0.406,1.292 1.406,1.677 1,0.385 10 false Active Air Fuel Ratio Control 0.25,2.135 1.563,2.344 1.313,0.208 10 false Target Air Fuel Ratio 2.698,1.385 2.948,1.573 0.25,0.188 10 false Off 2.073,2.052 3.135,2.427 1.063,0.375 10 false Stoichiometric Air Fuel Level 4.302,0.792 5.365,0.99 1.063,0.198 10 false 15 to 20 seconds 4.469,1.333 5.115,1.542 0.646,0.208 10 false Operation 4.625,1.656 5.125,1.833 0.5,0.177 10 false Normal 5.688,1.698 6.323,1.896 0.635,0.198 10 false Abnormal 0.292,3.271 1.375,3.729 1.083,0.458 10 false Heated Oxygen Sensor Voltage 2.51,3.521 2.969,3.708 0.458,0.188 10 false 0.21 V 4.75,2.469 5.042,2.667 0.292,0.198 10 false Rich 6.083,2.521 6.573,2.719 0.49,0.198 10 false Normal 5.906,4.104 6.573,4.292 0.667,0.188 10 false Abnormal 0.115,4.323 3.771,4.531 3.656,0.208 10 false Heated Oxygen Sensor Circuit High Voltage (P0138: Short) 4.51,4.938 5.115,5.135 0.604,0.198 10 false Operation 4.646,5.74 5,5.927 0.354,0.188 10 false Lean 2.792,4.99 3.052,5.167 0.26,0.177 10 false Off 2.146,5.708 3.177,6.094 1.031,0.385 10 false Stoichiometric Air Fuel Level 2.5,6.719 3,6.906 0.5,0.188 10 false 0.69 V 0.302,4.875 1.302,5.24 1,0.365 10 false Active Air Fuel Ratio Control 0.302,5.771 1.656,5.979 1.354,0.208 10 false Target Air Fuel Ratio 0.313,6.781 1.406,7.219 1.094,0.438 10 false Heated Oxygen Sensor Voltage 6.167,6.01 6.823,6.198 0.656,0.188 10 false Abnormal


CONFIRMATION DRIVING PATTERN

A264212E08
4.025,0.715 4.252,0.867 0.228,0.152 10 [C] 3.487,2.905 4.721,3.057 1.235,0.152 10 10 minutes or more 0.541,1.355 1.695,1.508 1.155,0.152 10 40 mph (60 km/h) 2.043,2.42 2.271,2.572 0.228,0.152 10 [A] 0.448,0.482 1.726,0.634 1.278,0.152 10 75 mph (120 km/h) 1.248,2.225 1.625,2.377 0.377,0.152 10 Idling 0.061,2.736 1.469,2.889 1.408,0.152 10 Engine Switch on (IG) 1.738,2.429 1.589,2.801 1.589,2.801 1.474,2.801 false 2.68,2.131 2.907,2.283 0.228,0.152 10 [B] 2.338,2.915 3.138,3.067 0.801,0.152 10 Warming up 5.007,3.309 5.235,3.462 0.228,0.152 10 [D]

1.

Connect the intelligent tester to the DLC3.

2.

Turn the engine switch on (IG) and turn the tester on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the engine switch off and wait for at least 30 seconds.

5.

Turn the engine switch on (IG) and turn the tester on [A].

6.

Start the engine and warm it up until the ECT reaches 75°C (167°F) or higher [B].

7.

Within the shift lever in D, drive the vehicle at 60 to 120 km/h (40 to 75 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Enter the following menus: Powertrain / Engine and ECT / DTC [D].

9.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0136, P0137 or P0138.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit




WIRING DIAGRAM

A235532E02
0.688,2.76 1.302,2.948 0.615,0.188 10 false FL MAIN 0.823,3.865 1.344,4.063 0.521,0.198 10 false Battery 0.979,1.208 1.271,1.396 0.292,0.188 10 false EFI 1.698,1.646 2.354,1.833 0.656,0.188 10 false EFI MAIN 0.688,1.896 1.396,2.083 0.708,0.188 10 false F/B BATT 3.49,0.938 3.719,1.115 0.229,0.177 10 false +B 3.875,0.938 4.292,1.115 0.417,0.177 10 false HT1B 3.49,1.646 3.719,1.823 0.229,0.177 10 false E2 3.281,0.938 3.406,1.115 0.125,0.177 10 false 2 2.313,0.938 2.438,1.115 0.125,0.177 10 false 3 2.313,1.219 2.438,1.396 0.125,0.177 10 false 1 1.552,0.938 1.677,1.115 0.125,0.177 10 false 5 1.552,1.219 1.677,1.396 0.125,0.177 10 false 2 3.281,1.729 3.406,1.906 0.125,0.177 10 false 4 4.344,0.938 4.469,1.115 0.125,0.177 10 false 1 5.323,0.854 5.51,1.031 0.188,0.177 10 false 47 5.302,1.073 5.51,1.25 0.208,0.177 10 false D2 5.323,1.635 5.51,1.813 0.188,0.177 10 false 64 5.302,1.854 5.51,2.031 0.208,0.177 10 false D2 5.323,2.302 5.51,2.479 0.188,0.177 10 false 87 5.302,2.51 5.51,2.688 0.208,0.177 10 false D2 5.323,3.698 5.51,3.875 0.188,0.177 10 false 44 5.302,3.885 5.51,4.063 0.208,0.177 10 false A7 4.344,1.729 4.469,1.906 0.125,0.177 10 false 3 3.885,1.646 4.292,1.823 0.406,0.177 10 false OX1B 4.521,1.375 5.125,1.521 0.604,0.146 10 false Shielded 3.104,2.01 3.396,2.188 0.292,0.177 10 false D59 3.104,2.177 4.573,2.354 1.469,0.177 10 false Heated Oxygen Sensor 5.615,1.844 6.052,2 0.438,0.156 10 false OX1B 5.615,0.958 6.031,1.115 0.417,0.156 10 false HT1B 5.615,2.49 6.073,2.646 0.458,0.156 10 false EX1B 5.615,3.792 6.083,3.948 0.469,0.156 10 false MREL 6.042,0.302 6.427,0.469 0.385,0.167 10 false ECM

CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the intelligent tester.

1.

Connect the intelligent tester to the DLC3.

2.

Start the engine.

3.

Turn the tester on.

4.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

5.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2.

6.

Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

7.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the tester.



HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



Tester Display
(Sensor)
Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V

NOTICE:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


Case Air Fuel Ratio Sensor (Sensor 1) Output Voltage Heated Oxygen Sensor (Sensor 2) Output Voltage Main Suspected Trouble Area
1
A373788E05
0.135,0.302 1.719,0.76 1.583,0.458 10 false Injection Volume 1.375,0.75 2.26,1.083 0.885,0.333 10 false 12.5% 1.333,1.167 2.219,1.5 0.885,0.333 10 false -12.5%

A373791E01
2.896,0.969 3.427,1.25 0.531,0.281 10 false OK 0.948,1.167 2.021,1.5 1.073,0.333 10 false Below 3.1 V 0.625,0.792 2.115,1.167 1.49,0.375 10 false Higher than 3.4 V 0.156,0.24 1.438,0.635 1.281,0.396 10 false Output Voltage

A373788E05
0.135,0.302 1.719,0.76 1.583,0.458 10 false Injection Volume 1.375,0.75 2.26,1.083 0.885,0.333 10 false 12.5% 1.333,1.167 2.219,1.5 0.885,0.333 10 false -12.5%

A373789E01
0.583,0.76 2.042,1.198 1.458,0.438 10 false Higher than 0.55 V 0.969,1.135 1.938,1.448 0.969,0.313 10 false Below 0.4 V 0.208,0.271 1.635,0.677 1.427,0.406 10 false Output Voltage 2.896,0.948 3.427,1.26 0.531,0.313 10 false OK

-
2
A373788E05
0.135,0.302 1.719,0.76 1.583,0.458 10 false Injection Volume 1.375,0.75 2.26,1.083 0.885,0.333 10 false 12.5% 1.333,1.167 2.219,1.5 0.885,0.333 10 false -12.5%

A373790E01
2.875,1.052 3.427,1.333 0.552,0.281 10 false NG 0.51,1.156 1.823,1.521 1.313,0.365 10 false Almost no reaction 0.354,0.469 1.49,0.906 1.135,0.438 10 false Output Voltage

A373788E05
0.135,0.302 1.719,0.76 1.583,0.458 10 false Injection Volume 1.375,0.75 2.26,1.083 0.885,0.333 10 false 12.5% 1.333,1.167 2.219,1.5 0.885,0.333 10 false -12.5%

A373789E01
0.583,0.76 2.042,1.198 1.458,0.438 10 false Higher than 0.55 V 0.969,1.135 1.938,1.448 0.969,0.313 10 false Below 0.4 V 0.208,0.271 1.635,0.677 1.427,0.406 10 false Output Voltage 2.896,0.948 3.427,1.26 0.531,0.313 10 false OK

·

Air fuel ratio sensor (sensor 1)

·

Air fuel ratio sensor (sensor 1) heater

·

Air fuel ratio sensor (sensor 1) circuit


3
A373788E05
0.135,0.302 1.719,0.76 1.583,0.458 10 false Injection Volume 1.375,0.75 2.26,1.083 0.885,0.333 10 false 12.5% 1.333,1.167 2.219,1.5 0.885,0.333 10 false -12.5%

A373791E01
2.896,0.969 3.427,1.25 0.531,0.281 10 false OK 0.948,1.167 2.021,1.5 1.073,0.333 10 false Below 3.1 V 0.625,0.792 2.115,1.167 1.49,0.375 10 false Higher than 3.4 V 0.156,0.24 1.438,0.635 1.281,0.396 10 false Output Voltage

A373788E05
0.135,0.302 1.719,0.76 1.583,0.458 10 false Injection Volume 1.375,0.75 2.26,1.083 0.885,0.333 10 false 12.5% 1.333,1.167 2.219,1.5 0.885,0.333 10 false -12.5%

A373790E01
2.875,1.052 3.427,1.333 0.552,0.281 10 false NG 0.51,1.156 1.823,1.521 1.313,0.365 10 false Almost no reaction 0.354,0.469 1.49,0.906 1.135,0.438 10 false Output Voltage

·

Heated oxygen sensor (sensor 2)

·

Heated oxygen sensor (sensor 2) heater

·

Heated oxygen sensor (sensor 2) circuit


4
A373788E05
0.135,0.302 1.719,0.76 1.583,0.458 10 false Injection Volume 1.375,0.75 2.26,1.083 0.885,0.333 10 false 12.5% 1.333,1.167 2.219,1.5 0.885,0.333 10 false -12.5%

A373790E01
2.875,1.052 3.427,1.333 0.552,0.281 10 false NG 0.51,1.156 1.823,1.521 1.313,0.365 10 false Almost no reaction 0.354,0.469 1.49,0.906 1.135,0.438 10 false Output Voltage

A373788E05
0.135,0.302 1.719,0.76 1.583,0.458 10 false Injection Volume 1.375,0.75 2.26,1.083 0.885,0.333 10 false 12.5% 1.333,1.167 2.219,1.5 0.885,0.333 10 false -12.5%

A373790E01
2.875,1.052 3.427,1.333 0.552,0.281 10 false NG 0.51,1.156 1.823,1.521 1.313,0.365 10 false Almost no reaction 0.354,0.469 1.49,0.906 1.135,0.438 10 false Output Voltage

·

Fuel injector

·

Fuel pressure

·

Gas leak from exhaust system (air fuel ratio extremely rich or lean)



·

Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.

·

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2; then press the view button.


NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ OUTPUT DTC (DTC P0136, P0137 OR P0138)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0138 is output A
DTC P0137 is output B
DTC P0136 is output C
DTC P0136, P0137 or P0138 and other DTCs are output D

HINT:

If any DTCs other than P0136, P0137 and P0138 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)

B

9.CHECK FOR EXHAUST GAS LEAK

C

7.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

D

2.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Start the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / O2S B1S2.


f.

Allow the engine to idle.


g.

Read the heated oxygen sensor output voltage while idling.

Result
Heated Oxygen Sensor Output Voltage Proceed to
1.0 V or higher A
Less than 1.0 V B



A

3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)

B

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)
a.
A103834E31
2.065,2.265 2.409,2.574 false 1.425,2.286 1.024,2.572 false 2.007,1.749 2.334,1.388 false 1.395,1.719 1.12,1.376 false 0.153,0.037 1.520,0.240 1.367,0.203 10 Component Side 0.742,0.571 2.260,0.774 1.519,0.203 10 Heated Oxygen Sensor 0.105,1.858 0.723,2.069 0.618,0.212 10 Sensor 2 0.788,1.206 1.022,1.409 0.234,0.203 10 +B 0.788,2.531 1.036,2.734 0.248,0.203 10 E2 2.405,1.206 2.845,1.409 0.440,0.203 10 HT1B 2.439,2.531 2.895,2.734 0.456,0.203 10 OX1B

Disconnect the HO2 sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connections Condition Specified Conditions
2 (+B) - 4 (E2) Always 10 kΩ or higher
2 (+B) - 3 (OX1B)




OK

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

NG

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connections Condition Specified Conditions
D2-47 (HT1B) - D2-64 (OX1B) Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Start the engine.


e.

Warm up the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2.


g.

Change the fuel injection volume using the tester and monitor the voltage output of the air fuel ratio and heated oxygen sensors displayed on the tester.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor is displayed as AFS Voltage B1S1, and the heated oxygen sensor is displayed as O2S B1S2 on the tester.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Result
Tester Display
(Sensor)
Voltage Variation Proceed to
AFS Voltage B1S1
(Air fuel ratio)
Alternates between higher and less than 3.3 V OK
Remains higher than 3.3 V NG
Remains less than 3.3 V NG

HINT:

A normal heated oxygen sensor voltage (O2S B1S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor (AFS Voltage B1S1) voltage remains either less or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A121606E78
5.885,2.479 6.365,1.396 false 5.552,2.271 6.365,1.396 false 5.708,1.667 6.365,1.396 false 5.563,2.448 5.844,2.667 false 3.021,1.26 2.865,1.677 false 4.333,1.813 4.094,1.688 false 3.573,2.604 3.188,2.917 false 1.958,1.99 2.125,1.99 false 1.958,2.948 2.156,2.948 false 1.531,1.896 1.906,2.052 0.375,0.156 10 false 3.3 V 2.667,0.26 3.083,0.458 0.417,0.198 10 false 12.5% 4.125,1.125 4.781,1.323 0.656,0.198 10 false -12.5% 1.656,2.854 1.906,3.052 0.25,0.198 10 false 1 V 1.667,3.385 1.906,3.583 0.24,0.198 10 false 0 V 3.073,1.146 4,1.344 0.927,0.198 10 false Malfunctioning 5.854,2.615 6.792,2.781 0.938,0.167 10 false Malfunctioning 4.76,0.125 5.823,0.323 1.063,0.198 10 false Injection Volume 3.635,2.51 5.563,2.729 1.927,0.219 10 false Heated Oxygen Sensor Output 6.406,1.125 6.938,1.813 0.531,0.688 10 false Air Fuel Ratio Sensor Output 4.406,1.75 4.906,1.948 0.5,0.198 10 false Normal



OK

6.CHECK AIR-FUEL RATIO SENSOR CURRENT

NG

15.REPLACE AIR-FUEL RATIO SENSOR
6.CHECK AIR-FUEL RATIO SENSOR CURRENT
HINT:

This air fuel ratio sensor test is to check the air fuel ratio sensor current during the fuel-cut operation. When the sensor is normal, the sensor current will indicate less than 3.6 mA in this test.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


f.

Drive the vehicle at 60 km/h (37 mph) or more for 10 minutes or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



g.

Stop the vehicle.


h.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / AFS Current B1S1.


i.

Drive the vehicle at 60 km/h (37 mph) or more and decelerate the vehicle for 5 seconds or more. Perform this 3 times.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


A152792E43
1.357,2.513 2.638,2.697 1.281,0.184 10 10 minutes or more 2.973,2.513 4.186,2.697 1.213,0.184 10 5 seconds or more 4.271,2.513 5.468,2.697 1.197,0.184 10 5 seconds or more 5.56,2.513 6.739,2.697 1.179,0.184 10 5 seconds or more 0.152,0.078 1.451,0.293 1.299,0.215 12 Driving Pattern: 0.455,1.379 1.114,1.594 0.658,0.215 10 60 km/h 0.527,2.139 1.062,2.342 0.536,0.203 10 0 km/h


j.

Read the value of the air fuel ratio sensor current while the fuel-cut operation is being performed.

Standard current:

Less than 3.6 mA


HINT:
·

To measure the air fuel ratio sensor current precisely, perform the fuel-cut operation as long as possible.

·

If it is difficult to measure the air fuel ratio sensor current, use the snapshot function of the tester.





OK

12.REPLACE HEATED OXYGEN SENSOR

NG

15.REPLACE AIR-FUEL RATIO SENSOR
7.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / O2S B1S2.


f.

Change the fuel injection volume using the tester and monitor the voltage output of the heated oxygen sensors displayed on the tester.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The heated oxygen sensor has a maximum output delay of approximately 20 seconds.



Standard voltage:

Fluctuates between 0.4 V or less and 0.55 V or higher.




OK

8.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

NG

9.CHECK FOR EXHAUST GAS LEAK
8.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Start the engine.


e.

Warm up the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2.


g.

Change the fuel injection volume using the tester and monitor the voltage output of the air fuel ratio and heated oxygen sensors displayed on the tester.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor is displayed as AFS Voltage B1S1, and the heated oxygen sensor is displayed as O2S B1S2 on the tester.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Result
Tester Display
(Sensor)
Voltage Variation Proceed to
AFS Voltage B1S1
(Air fuel ratio)
Alternates between higher and less than 3.3 V OK
Remains higher than 3.3 V NG
Remains less than 3.3 V NG

HINT:

A normal heated oxygen sensor voltage (O2S B1S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor (AFS Voltage B1S1) voltage remains either less or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A121606E78
5.885,2.479 6.365,1.396 false 5.552,2.271 6.365,1.396 false 5.708,1.667 6.365,1.396 false 5.563,2.448 5.844,2.667 false 3.021,1.26 2.865,1.677 false 4.333,1.813 4.094,1.688 false 3.573,2.604 3.188,2.917 false 1.958,1.99 2.125,1.99 false 1.958,2.948 2.156,2.948 false 1.531,1.896 1.906,2.052 0.375,0.156 10 false 3.3 V 2.667,0.26 3.083,0.458 0.417,0.198 10 false 12.5% 4.125,1.125 4.781,1.323 0.656,0.198 10 false -12.5% 1.656,2.854 1.906,3.052 0.25,0.198 10 false 1 V 1.667,3.385 1.906,3.583 0.24,0.198 10 false 0 V 3.073,1.146 4,1.344 0.927,0.198 10 false Malfunctioning 5.854,2.615 6.792,2.781 0.938,0.167 10 false Malfunctioning 4.76,0.125 5.823,0.323 1.063,0.198 10 false Injection Volume 3.635,2.51 5.563,2.729 1.927,0.219 10 false Heated Oxygen Sensor Output 6.406,1.125 6.938,1.813 0.531,0.688 10 false Air Fuel Ratio Sensor Output 4.406,1.75 4.906,1.948 0.5,0.198 10 false Normal



OK

CHECK AND REPAIR EXTREMELY RICH OR LEAN ACTUAL AIR-FUEL RATIO (INJECTOR, FUEL PRESSURE, GAS LEAK FROM EXHAUST SYSTEM, ETC.)

NG

15.REPLACE AIR-FUEL RATIO SENSOR
9.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leak.

OK:

No gas leak.




OK

10.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

10.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

OK

11.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

11.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the HO2 sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connections Condition Specified Conditions
D59-1 (HT1B) - D2-47 (HT1B) Always Below 1 Ω
D59-3 (OX1B) - D2-64 (OX1B)
D59-4 (E2) - D2-87 (EX1B)


Standard Resistance (Check for short):
Tester Connections Condition Specified Conditions
D59-1 (HT1B) or D2-47 (HT1B) - Body ground Always 10 kΩ or higher
D59-3 (OX1B) or D2-64 (OX1B) - Body ground




OK

12.REPLACE HEATED OXYGEN SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.REPLACE HEATED OXYGEN SENSOR
a.


NEXT

13.PERFORM CONFIRMATION DRIVING PATTERN
13.PERFORM CONFIRMATION DRIVING PATTERN
a.

Perform the Confirmation Driving Pattern.



NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137 OR P0138)
14.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137 OR P0138)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


e.

Input the DTC: P0136, P0137 or P0138.


f.

Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again but increase the vehicle speed.

Result
Result Proceed to
ABNORMAL
(DTC P0136, P0137 or P0138 is output)
A
NORMAL
(DTC is not output)
B



A

B

END

15.REPLACE AIR-FUEL RATIO SENSOR
a.


NEXT

16.PERFORM CONFIRMATION DRIVING PATTERN
16.PERFORM CONFIRMATION DRIVING PATTERN
a.

Perform the Confirmation Driving Pattern.



NEXT

17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137 OR P0138)
17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137 OR P0138)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


e.

Input the DTC: P0136 or P0138.


f.

Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again but increase the vehicle speed.

Result
Result Proceed to
ABNORMAL
(DTC P0136 or P0138 is output)
A
NORMAL
(DTC is not output)
B



A

B

END