Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › 2013.04–2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P0037  Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)  P0038  Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)  


DESCRIPTION


HINT:
·

Sensor 2 refers to the sensor mounted behind the Three-Way Catalytic Converter (TWC) and located far from the engine assembly.

·

When any of these DTCs are set, the ECM enters fail-safe mode. The ECM turns off the Heated Oxygen (HO2) sensor heater in fail-safe mode. Fail-safe mode continues until the engine switch is turned off.

·

The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The HO2 sensor heater circuit uses a relay on the +B side of the circuit.

A140671E02
0.117,0.076 2.866,0.265 2.749,0.188 10 Reference (System Diagram of Sensor 2) 1.278,0.878 1.511,1.059 0.233,0.181 10 EFI 2.099,0.632 2.746,0.813 0.647,0.181 10 EFI MAIN 3.377,0.386 4.957,0.568 1.580,0.181 10 Heated Oxygen Sensor 3.457,1.017 3.647,1.198 0.191,0.181 10 +B 4.55,1.024 4.930,1.205 0.380,0.181 10 HT1B 3.457,1.588 3.685,1.769 0.229,0.181 10 E2 4.55,1.595 4.977,1.776 0.427,0.181 10 OX1B 3.885,0.842 4.320,1.023 0.436,0.181 10 Heater 3.871,1.432 4.330,1.614 0.459,0.181 10 Sensor 5.874,0.365 6.200,0.547 0.326,0.181 10 ECM 5.138,1.024 5.518,1.205 0.380,0.181 10 HT1B 5.138,1.595 5.539,1.776 0.401,0.181 10 OX1B 5.138,2.166 5.527,2.347 0.389,0.181 10 EX1B 5.138,2.733 5.541,2.914 0.403,0.181 10 MREL 0.494,1.043 0.985,1.403 0.492,0.360 10 From Battery



DTC No. DTC Detection Condition Trouble Area
P0037 Heated Oxygen (HO2) sensor heater current less than 0.3 A
(1 trip detection logic)
·

Open in HO2 sensor heater circuit

·

HO2 sensor (sensor 2)

·

ECM


P0038 Heated Oxygen (HO2) sensor heater current reaches high limit
(1 trip detection logic)
·

Short in HO2 sensor heater circuit

·

HO2 sensor (sensor 2)

·

ECM



MONITOR DESCRIPTION

The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature, and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.

Heated Oxygen Sensor Heater Range Check (P0037 or P0038):

The ECM monitors the current applied to the heated oxygen sensor heater to check the heater for malfunctions.

If the heater current is outside the normal range, the signal transmitted by the heated oxygen sensor becomes inaccurate. When the current in the heated oxygen sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Change the fuel injection volume using the Control the Injection Volume for A/F Sensor function provided in the Active Test and monitor the heated oxygen sensor output voltage (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>P0136). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



PROCEDURE

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

OK

2.CHECK TERMINAL VOLTAGE (+B OF HO2 SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (+B OF HO2 SENSOR)
a.
A394017E01
0.583,1 1,1.25 0.417,0.25 1.844,1.146 2.208,0.948 false 0.104,0.083 1.615,0.365 1.51,0.281 10 false Wire Harness Side 0.552,0.448 2.938,0.688 2.385,0.24 10 false Heated Oxygen Sensor Connector 0.656,1.031 0.969,1.229 0.313,0.198 10 false D59 0.51,1.333 1.125,1.594 0.615,0.26 10 false Sensor 2 1.385,1.729 2.292,1.969 0.906,0.24 10 false Front View 2.26,0.844 2.573,1.042 0.313,0.198 10 false +B

Disconnect the HO2 sensor connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D59-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (HO2 SENSOR - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (HO2 SENSOR - EFI MAIN RELAY)

3.CHECK HARNESS AND CONNECTOR (HO2 SENSOR - ECM)
a.

Disconnect the HO2 sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D59-1 (HT1B) - D2-47 (HT1B) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
D59-1 (HT1B) or D2-47 (HT1B) - Body ground Always 10 kΩ or higher




OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester ON.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Allow the engine to idle for 2 minutes or more.


h.

Enter the following menus: Powertrain / Engine and ECT / DTC.


i.

Read DTCs.


Result:
Display (DTC Output) Proceed to
No output A
P0037 or P0038 B



A

B