The ECM uses sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.
The first sensor, the air fuel ratio sensor, sends pre-catalyst information to the ECM. The second sensor, the heated oxygen sensor, sends post-catalyst information to the ECM.
In order to detect any deterioration in the three-way catalytic converter, the ECM calculates the oxygen storage capacity of the three-way catalytic converter. This calculation is based on the voltage output of the heated oxygen sensor while performing active air fuel ratio control.
The oxygen storage capacity value is an indication of the oxygen storage capacity of the three-way catalytic converter. When the vehicle is being driven with a warm engine, active air fuel ratio control is performed for approximately 15 to 20 seconds. When it is performed, the ECM deliberately sets the air fuel ratio to lean or rich levels. If the cycle of the waveform for the heated oxygen sensor is long, the oxygen storage capacity is great. There is a direct correlation between the heated oxygen sensor and the oxygen storage capacity of the three-way catalytic converter.
The ECM uses the oxygen storage capacity value to determine the state of the three-way catalytic converter. If any deterioration has occurred, the ECM illuminates the MIL and stored the DTC.
This system determines the deterioration of the entire catalyst system (including the front and rear catalysts), by using the oxygen storage capacity value of the front catalyst, that is more sensitive than the rear catalyst, as the representative value. Therefore, be sure to replace the front and rear catalysts together when catalyst replacement is necessary.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0420 | The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip detection logic). | ·
Gas leak from exhaust system ·
Air fuel ratio sensor (sensor 1) ·
Heated oxygen sensor (sensor 2) ·
Exhaust manifold converter sub-assembly (TWC: Front catalyst) and center exhaust pipe assembly (TWC: Rear catalyst) |
| *1 | Exhaust Manifold Converter Sub-assembly
(TWC: Front Catalyst) |
*2 | Air fuel ratio Sensor |
| *3 | Front Exhaust Pipe Assembly | *4 | Heated oxygen Sensor |
| *5 | Center Exhaust Pipe Assembly
(TWC: Rear Catalyst) |
*6 | Tail Pipe Assembly |
Replace the exhaust manifold converter sub-assembly (*1) and the center exhaust pipe assembly (*5) together when catalyst replacement is necessary. (Excluding air fuel ratio sensor *2 and heated oxygen sensor *4)
Performing this confirmation driving pattern will activate the catalyst efficiency monitor. This is very useful for verifying the completion of a repair.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG) and turn the tester on.
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].
Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [B].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Drive the vehicle while keeping the engine load as constant as possible.
Turn the engine switch off and wait for at least 30 seconds [C].
Turn the engine switch on (IG) and turn the tester on.
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [D].
Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [E].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Drive the vehicle while keeping the engine load as constant as possible.
Enter the following menus: Powertrain / Engine and ECT / DTC [F].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Drive the vehicle at a speed between 75 and 100 km/h (47 and 62 mph) for 10 minutes or more [G].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Drive the vehicle while keeping the engine load as constant as possible.
Enter the following menus: Powertrain / Engine and ECT / DTC [H].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, the system is normal.
Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the air fuel ratio and heated oxygen sensors. This is to activate the sensors sufficiently to obtain appropriate inspection results.
(a) Connect the intelligent tester to the DLC3.
(b) Start the engine and warm it up with all the accessories switched off until the engine coolant temperature stabilizes.
(c) Run the engine at an engine speed of between 2500 rpm and 3000 rpm for at least 3 minutes.
(d) While running the engine at 3000 rpm for 2 seconds, and then 2000 rpm for 2 seconds, check the waveforms of the air fuel ratio and heated oxygen sensors using the tester.
If the voltage output of either the air fuel ratio or heated oxygen sensor does not fluctuate, or there is a noise in the waveform of either sensor, the sensor may be malfunctioning.
If the voltage outputs of both the sensors remain lean or rich, the air fuel ratio may be extremely lean or rich. In such cases, perform the Control the Injection Volume for A/F Sensor Active Test using the tester.
If the Three-way Catalytic Converter (TWC) has deteriorated, the heated oxygen sensor (located behind the Three-way Catalytic Converter [TWC]) voltage output fluctuates up and down frequently, even under normal driving conditions (active air fuel ratio control is not performed).
If a malfunction cannot be found when troubleshooting DTC P0420, a lean or rich abnormality may be the cause. Perform troubleshooting by following the inspection procedure for P0171 (System Too Lean) and P0172 (System Too Rich).
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0420 is output | A |
| DTC P0420 and other DTCs are output | B |
If any DTCs other than P0420 are output, troubleshoot those DTCs first.
A
B
Connect the intelligent tester to the DLC3.
Start the engine and warm it up.
Turn the tester on.
Run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2.
Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
Monitor the voltage outputs of the air fuel ratio sensor and heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the tester.
The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.
Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.
| Tester Display
(Sensor) |
Injection Volume | Status | Voltage |
|---|---|---|---|
| AFS Voltage B1S1
(Air fuel ratio) |
12.5% | Rich | Below 3.1 V |
| -12.5% | Lean | Higher than 3.4 V | |
| O2S B1S2
(Heated oxygen) |
12.5% | Rich | Higher than 0.55 V |
| -12.5% | Lean | Below 0.4 V |
| Status
AFS Voltage B1S1 |
Status
O2S B1S2 |
Actual air fuel ratio, air fuel ratio sensor and
heated oxygen sensor condition |
Misfire | Main Suspected Trouble Area | Proceed to |
|---|---|---|---|---|---|
| Lean/Rich | Lean/Rich | Normal | - | ·
Three-way catalytic converter ·
Gas leak from exhaust system |
A |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | - | ·
Air fuel ratio sensor |
B |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | - | ·
Air fuel ratio sensor |
|
| Lean/Rich | Lean | Heated oxygen sensor malfunction | - | ·
Heated oxygen sensor ·
Gas leak from exhaust system |
C |
| Lean/Rich | Rich | Heated oxygen sensor malfunction | - | ·
Heated oxygen sensor ·
Gas leak from exhaust system |
|
| Lean | Lean | Actual air fuel ratio lean | May occur | ·
Extremely rich or lean actual air fuel ratio ·
Gas leak from exhaust system |
D |
| Rich | Rich | Actual air fuel ratio rich | - | ·
Extremely rich or lean actual air fuel ratio ·
Gas leak from exhaust system |
Lean: During Control the Injection Volume for A/F Sensor, the air fuel ratio sensor output voltage (AFS Voltage B1S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S B1S2) is consistently below 0.4 V.
Rich: During Control the Injection Volume for A/F Sensor, the AFS Voltage B1S1 is consistently below 3.1 V, and the O2S B1S2 is consistently higher than 0.55 V.
Lean/Rich: During Control the Injection Volume for A/F Sensor of the Active Test, the output voltage of the air fuel ratio sensor and heated oxygen sensor alternate correctly.
A
B
C
D
Check for exhaust gas leaks.
No gas leaks.
OK
NG
Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst) and the center exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.
Confirm the replacement parts, referring to the illustration in the Catalyst Location.
Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst) (See page Engine / Hybrid System>2AZ-FE ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY).
Replace the center exhaust pipe assembly (TWC: Rear catalyst) (See page Engine / Hybrid System>2AZ-FE EXHAUST>EXHAUST PIPE>REMOVAL).
NEXT
Replace the air fuel ratio sensor (See page Engine / Hybrid System>2AZ-FE EMISSION CONTROL>AIR FUEL RATIO SENSOR>REMOVAL).
NEXT
Check for exhaust gas leaks.
No gas leaks.
OK
NG
Replace the heated oxygen sensor (See page Engine / Hybrid System>2AZ-FE EMISSION CONTROL>HEATED OXYGEN SENSOR>REMOVAL).
NEXT
Check the exhaust gas leaks.
No gas leaks.
OK
NG
Check the cause of extremely rich or lean actual air fuel ratio, referring to the DTC P0171 Inspection Procedure (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>P0171).
NEXT
Repair or replace exhaust gas leak point.
NEXT
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Clear the DTCs (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off and wait for at least 30 seconds.
Start the engine.
Turn the tester on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0420 is output | A |
| DTC is not output
(Pending DTCs is not output) |
B |
A
B
Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst) and the center exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.
Confirm the replacement parts, referring to the illustration in the Catalyst Location.
Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst) (See page Engine / Hybrid System>2AZ-FE ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY).
Replace the center exhaust pipe assembly (TWC: Rear catalyst) (See page Engine / Hybrid System>2AZ-FE EXHAUST>EXHAUST PIPE>REMOVAL).
NEXT