Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM J

2AZ-FE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates 5 V power from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A283092E02
4.378,1.174 6.206,1.346 1.828,0.172 10 5 V Constant Voltage Circuit 5.358,2.025 6.373,2.439 1.015,0.414 10 Microprocessor 1.715,1.108 2.750,1.271 1.035,0.162 10 from EFI Fuse 1.271,1.465 2.701,1.634 1.430,0.170 10 from EFI MAIN Relay 2.976,1.019 3.501,1.239 0.524,0.220 10 BATT 0.316,2.059 2.691,2.546 2.375,0.487 10 Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (Sensors which have IC) 0.316,3.045 2.680,3.374 2.364,0.329 10 Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.072,3.124 4.331,3.333 0.260,0.210 10 R 3.042,1.369 3.324,1.571 0.281,0.202 10 +B 3.17,2.288 3.457,2.522 0.287,0.233 10 VC 4.886,0.457 5.337,0.680 0.451,0.224 10 ECM

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are deactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated when the engine switch is turned on (IG). The MIL goes off when the engine is started.


WIRING DIAGRAM

A235542E02
0.583,2.229 3.094,2.385 2.51,0.156 10 false Throttle Position Sensor (Throttle Body) 0.875,4 2.375,4.188 1.5,0.188 10 false Battery Current Sensor 0.521,6.521 2.667,6.719 2.146,0.198 10 false Accelerator Pedal Position Sensor 2.094,0.875 2.302,1.052 0.208,0.177 10 false VC 2,1.229 2.302,1.406 0.302,0.177 10 false VTA 1.948,1.594 2.313,1.771 0.365,0.177 10 false VTA2 2.125,1.927 2.313,2.104 0.188,0.177 10 false E2 5.5,6.938 5.875,7.115 0.375,0.177 10 false ECM 2.135,3.021 2.323,3.198 0.188,0.177 10 false IB 1.906,4.469 2.302,4.646 0.396,0.177 10 false VCPA 1.927,4.802 2.302,4.979 0.375,0.177 10 false VCP2 2.01,5.146 2.302,5.323 0.292,0.177 10 false VPA 1.938,5.5 2.313,5.677 0.375,0.177 10 false VPA2 2.01,5.854 2.302,6.031 0.292,0.177 10 false EPA 1.938,6.198 2.313,6.375 0.375,0.177 10 false EPA2 4.979,1.24 5.344,1.417 0.365,0.177 10 false VTA1 4.979,0.781 5.396,0.958 0.417,0.177 10 false VCTA 4.979,1.583 5.344,1.76 0.365,0.177 10 false VTA2 4.979,1.833 5.271,2.01 0.292,0.177 10 false ETA 4.979,4.396 5.375,4.573 0.396,0.177 10 false VCPA 4.979,4.74 5.354,4.917 0.375,0.177 10 false VCP2 4.979,5.177 5.271,5.354 0.292,0.177 10 false VPA 4.979,5.521 5.354,5.698 0.375,0.177 10 false VPA2 4.979,5.781 5.271,5.958 0.292,0.177 10 false EPA 4.979,6.115 5.354,6.292 0.375,0.177 10 false EPA2 1.99,2.688 2.344,2.865 0.354,0.177 10 false VC5 2.01,3.365 2.302,3.542 0.292,0.177 10 false THB 2.125,3.708 2.313,3.885 0.188,0.177 10 false E2 4.979,2.573 5.344,2.76 0.365,0.188 10 false VCIB 4.979,3.646 5.313,3.823 0.333,0.177 10 false E1B 4.979,3.365 5.271,3.542 0.292,0.177 10 false THB 5.844,0.573 6.073,0.75 0.229,0.177 10 false 5 V 4.979,3.021 5.167,3.198 0.188,0.177 10 false IB 4.667,3.021 4.875,3.198 0.208,0.177 10 false D2 4.677,2.875 4.885,3.052 0.208,0.177 10 false 68 4.667,3.385 4.875,3.563 0.208,0.177 10 false D2 4.635,3.219 4.906,3.396 0.271,0.177 10 false 120 4.667,3.729 4.875,3.906 0.208,0.177 10 false D2 4.677,3.563 4.885,3.74 0.208,0.177 10 false 92 4.667,4.5 4.875,4.677 0.208,0.177 10 false A7 4.677,4.333 4.885,4.51 0.208,0.177 10 false 57 4.667,4.844 4.875,5.021 0.208,0.177 10 false A7 4.677,4.677 4.885,4.854 0.208,0.177 10 false 58 4.667,5.188 4.875,5.365 0.208,0.177 10 false A7 4.677,5.021 4.885,5.198 0.208,0.177 10 false 55 4.667,5.531 4.875,5.708 0.208,0.177 10 false A7 4.677,5.365 4.885,5.542 0.208,0.177 10 false 56 4.667,5.875 4.875,6.052 0.208,0.177 10 false A7 4.677,5.708 4.885,5.885 0.208,0.177 10 false 59 4.667,6.208 4.875,6.385 0.208,0.177 10 false A7 0.26,6.521 0.469,6.698 0.208,0.177 10 false A3 0.625,4 0.833,4.177 0.208,0.177 10 false A2 0.26,2.229 0.552,2.406 0.292,0.177 10 false D41 4.677,6.052 4.885,6.229 0.208,0.177 10 false 60 2.406,6.063 2.542,6.24 0.135,0.177 10 false 2 2.406,5.719 2.542,5.896 0.135,0.177 10 false 5 2.406,5.365 2.542,5.542 0.135,0.177 10 false 3 2.406,5.021 2.542,5.198 0.135,0.177 10 false 6 2.406,4.677 2.542,4.854 0.135,0.177 10 false 1 2.406,4.333 2.542,4.51 0.135,0.177 10 false 4 2.406,3.615 2.542,3.792 0.135,0.177 10 false 4 2.406,3.26 2.542,3.438 0.135,0.177 10 false 1 2.406,2.927 2.542,3.104 0.135,0.177 10 false 3 2.406,2.583 2.542,2.76 0.135,0.177 10 false 2 2.406,1.823 2.542,2 0.135,0.177 10 false 3 2.406,1.469 2.542,1.646 0.135,0.177 10 false 4 2.406,1.135 2.542,1.313 0.135,0.177 10 false 6 2.406,0.76 2.542,0.938 0.135,0.177 10 false 5 4.667,2.688 4.875,2.865 0.208,0.177 10 false D2 4.677,2.521 4.885,2.698 0.208,0.177 10 false 69 4.667,1.927 4.875,2.104 0.208,0.177 10 false D2 4.677,1.76 4.885,1.938 0.208,0.177 10 false 91 4.667,1.583 4.875,1.76 0.208,0.177 10 false D2 4.635,1.427 4.896,1.604 0.26,0.177 10 false 114 4.667,1.24 4.875,1.417 0.208,0.177 10 false D2 4.635,1.073 4.896,1.25 0.26,0.177 10 false 115 4.667,0.896 4.875,1.073 0.208,0.177 10 false D2 4.677,0.729 4.885,0.906 0.208,0.177 10 false 67

PROCEDURE

1.CHECK MIL CONDITION
a.

Check that the Malfunction Indicator Lamp (MIL) lights up when turning the engine switch on (IG).

OK:

MIL lights up




NG

2.CHECK CONNECTION BETWEEN GTS AND ECM

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and GTS on.


c.

Check the communication between the GTS and ECM.

Result:
Result Proceed to
Communication is possible A
Communication is not possible B




B

3.CHECK MIL (BATTERY CURRENT SENSOR)

A

3.CHECK MIL (BATTERY CURRENT SENSOR)
a.

Disconnect the battery current sensor connector.


b.

Turn the engine switch on (IG).


c.

Check the MIL.

Result:
Result Proceed to
MIL illuminates A
MIL does not illuminate B




B

4.CHECK MIL (THROTTLE POSITION SENSOR)

A

REPLACE BATTERY CURRENT SENSOR

4.CHECK MIL (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle body assembly connector.


b.

Turn the engine switch on (IG).


c.

Check the MIL.

Result:
Result Proceed to
MIL illuminates A
MIL does not illuminate B




B

5.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)

A

5.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Turn the engine switch on (IG).


c.

Check the MIL.

Result:
Result Proceed to
MIL illuminates A
MIL does not illuminate B




B

6.CHECK HARNESS AND CONNECTOR

A

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

6.CHECK HARNESS AND CONNECTOR
a.

Disconnect the battery current sensor connector.


b.

Disconnect the throttle body assembly connector.


c.

Disconnect the accelerator pedal position sensor connector.


d.

Disconnect the ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (check for short):
Tester Connection Condition Specified Condition
D2-69 (VCIB) - Body ground Always 10 kΩ or higher
D2-67 (VCTA) - Body ground Always 10 kΩ or higher
A7-57 (VCPA) - Body ground Always 10 kΩ or higher
A7-58 (VCP2) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR