Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › 2013.04–2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P0327  Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)  P0328  Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)  


DESCRIPTION

A flat type knock sensor (non-resonant type) has a structure that can detect vibrations between approximately 5 kHz and 15 kHz.

The knock sensor is fitted onto the engine block to detect engine knocking.

The knock sensor contains a piezoelectric element which generates a voltage when it becomes deformed.

The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.

DTC No. DTC Detection Condition Trouble Area
P0327 Output voltage of knock sensor is 0.5 V or less
(1 trip detection logic)
·

Short in knock sensor circuit

·

Knock sensor

·

ECM


P0328 Output voltage of knock sensor is 4.5 V or more
(1 trip detection logic)
·

Open in knock sensor circuit

·

Knock sensor

·

ECM



HINT:

When any of DTCs P0327 and P0328 are set, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the engine switch is turned off.


Reference: Inspection using an oscilloscope

A306169E03
2.646,1 3.104,1.198 0.458,0.198 10 false GND 2.417,0.229 3.104,0.458 0.688,0.229 10 false 1 V/DIV. 1.104,1.917 2.104,2.104 1,0.188 10 false 1 ms./DIV. 0.604,0.052 2.135,0.229 1.531,0.177 10 false KNK1 Signal Waveform

The correct waveform is as shown.

Item Content
Symbols (Terminal No.) D2-110 (KNK1) - D2-111 (EKNK)
Tool Setting 1 V/DIV.
1 msec./DIV.
Condition Engine speed maintained at 4,000 rpm with warming up engine

WIRING DIAGRAM

A107909E15
0.659,0.431 1.583,0.708 0.924,0.276 10 Knock Sensor 0.659,0.263 0.941,0.540 0.282,0.276 10 D52 3.12,0.226 3.730,0.521 0.610,0.295 10 Shielded 5.904,0.031 6.229,0.212 0.326,0.181 10 ECM 5.623,0.031 5.821,0.212 0.197,0.181 10 D2 6.193,0.386 6.419,0.567 0.225,0.181 10 5 V 5.469,0.708 5.849,0.889 0.380,0.181 10 KNK1 5.469,1.511 5.865,1.693 0.395,0.181 10 EKNK 5.112,0.708 5.373,0.889 0.260,0.181 10 110 5.112,1.511 5.368,1.693 0.256,0.181 10 111 1.595,0.708 1.693,0.889 0.097,0.181 10 2 1.595,1.511 1.691,1.693 0.096,0.181 10 1

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (KNOCK FEEDBACK VALUE)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Knock Feedback Value.


f.

Read the value while driving the vehicle.

OK:

The value changes.


HINT:
Malfunction does not occur Knock Feedback Value changes
Malfunctions occur Knock Feedback Value does not change

The Knock Feedback Value change can be confirmed by running the engine with a high load, for example, by activating the air conditioning system and racing the engine.




NG

2.INSPECT ECM (KNK1 VOLTAGE)

OK

2.INSPECT ECM (KNK1 VOLTAGE)
U188247E02
0.146,0.083 1.427,0.271 1.281,0.188 10 false Wire Harness Side 1.26,1.49 1.938,1.667 0.677,0.177 10 false Front View 2.302,0.802 3.219,1.156 0.917,0.354 10 false Knock Sensor Connector 1.573,0.917 1.729,1.094 0.156,0.177 10 false 1 1.781,0.917 1.938,1.094 0.156,0.177 10 false 2 0.51,0.771 0.802,0.948 0.292,0.177 10 false D52

a.

Disconnect the knock sensor connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D52-2 - D52-1 Engine switch on (IG) 4.5 to 5.5 V




OK

3.INSPECT KNOCK SENSOR

NG

4.CHECK HARNESS AND CONNECTOR (KNOCK SENSOR - ECM)
3.INSPECT KNOCK SENSOR

OK

NG

4.CHECK HARNESS AND CONNECTOR (KNOCK SENSOR - ECM)
a.

Disconnect the knock sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D52-2 - D2-110 (KNK1) Always Below 1 Ω
D52-1 - D2-111 (EKNK) Always Below 1 Ω
D52-2 or D2-110 (KNK1) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR