Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P0335  Crankshaft Position Sensor "A" Circuit  P0339  Crankshaft Position Sensor "A" Circuit Intermittent  


DESCRIPTION

The Crankshaft Position (CKP) sensor system consists of a crankshaft position sensor plate and a pickup coil.

The crankshaft position sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet. The crankshaft position sensor plate rotates and, as each tooth passes by the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per crankshaft revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the fuel injection and ignition timing are controlled.

DTC No. DTC Detection Condition Trouble Area
P0335 One of the following conditions is met (1 trip detection logic):
·

No crankshaft position sensor signal to ECM while cranking

·

No crankshaft position sensor signal to ECM while engine running

·

Missing crankshaft position sensor signal despite camshaft position sensor signal inputs normal after engine cranked


·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft position sensor plate

·

ECM


P0339 All of the following conditions are met (1 trip detection logic):
(a) The engine speed is 1000 rpm or higher.
(b) No crankshaft position sensor signal for 0.05 seconds or more.
(c) 3 seconds or more have elapsed since the starter signal switched from on to off.
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft position sensor plate

·

ECM



A063955E86
2.802,0.573 3.125,0.75 0.323,0.177 10 false GND 2.802,1.375 3.125,1.552 0.323,0.177 10 false GND 0.167,0.49 0.458,0.667 0.292,0.177 10 false CH1 0.094,0.667 0.49,0.844 0.396,0.177 10 false (G2+) 0.167,1.281 0.458,1.458 0.292,0.177 10 false CH2 0.094,1.458 0.479,1.635 0.385,0.177 10 false (NE+) 1.063,1.896 1.948,2.073 0.885,0.177 10 false 20 msec./DIV. 2.75,0.031 3.281,0.208 0.531,0.177 10 false 5 V/DIV.

Reference: Inspection using an oscilloscope.

HINT:
·

The correct waveform is as shown.


·

G2 stands for the Camshaft Position (CMP) sensor signal, and NE stands for the CKP sensor signal.

·

Grounding failure of the shielded wire may cause noise in waveforms.



Item Content
Symbols (Terminal No.) CH1: D2-99 (G2+) - D2-98 (G2-)
CH2: D2-122 (NE+) - D2-121 (NE-)
Tool Setting 5 V/DIV.
20 msec./DIV.
Condition Idling


WIRING DIAGRAM

A127258E09
0.052,3.625 1.385,4.021 1.333,0.396 10 false Crankshaft Position Sensor Plate 0.198,0.948 1.281,1.135 1.083,0.188 10 false Intake Camshaft 0.865,2.469 2.948,2.677 2.083,0.208 10 false Crankshaft Position Sensor 0.521,2.469 0.802,2.677 0.281,0.208 10 false D54 1.26,0.625 3.344,0.833 2.083,0.208 10 false Camshaft Position Sensor 0.927,0.625 1.208,0.833 0.281,0.208 10 false D55 2.677,2.552 3.396,2.75 0.719,0.198 10 false Shielded 3.375,0.615 4.094,0.813 0.719,0.198 10 false Shielded 6.49,0.417 6.938,0.615 0.448,0.198 10 false ECM 6.208,0.417 6.417,0.615 0.208,0.198 10 false D2 6.281,1.583 6.667,1.781 0.385,0.198 10 false G2- 6.104,0.927 6.49,1.125 0.385,0.198 10 false G2+ 6.115,3.052 6.5,3.25 0.385,0.198 10 false NE- 6.104,3.49 6.49,3.688 0.385,0.198 10 false NE+ 5.844,1.583 6.021,1.781 0.177,0.198 10 false 98 5.844,0.927 6.021,1.125 0.177,0.198 10 false 99 5.76,2.813 6.021,3.01 0.26,0.198 10 false 121 5.76,3.469 6.021,3.667 0.26,0.198 10 false 122 2.469,1.583 2.646,1.781 0.177,0.198 10 false 2 2.469,0.927 2.646,1.125 0.177,0.198 10 false 1 2.469,2.813 2.573,3.01 0.104,0.198 10 false 2 2.469,3.469 2.573,3.667 0.104,0.198 10 false 1 6.135,4.552 6.396,4.75 0.26,0.198 10 false E1 5.76,4.469 6.021,4.667 0.26,0.198 10 false 104

CAUTION / NOTICE / HINT

HINT:
·

After performing the inspection procedure for the crankshaft position sensor, if DTC P0335 is output again, check the following items related to the camshaft position sensor.

-

Installation condition of the camshaft position sensor

-

Installation condition of the camshaft

-

Connection of the camshaft position sensor connector



·

If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.

·

The engine speed can be checked by using the GTS. To perform the check, follow the procedures below:

(a)

Connect the GTS to the DLC3.

(b)

Start the engine.

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.


The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.



·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS ON.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.


e.

Start the engine.


f.

Read the values displayed on the GTS while the engine is running.

OK:

Correct values are displayed.


HINT:
·

To check the engine speed change, display the graph on the GTS.

·

If the engine does not start, check the engine speed while cranking.

·

If the engine speed indicated on the GTS remains zero (0), there may be an open or short in the crankshaft position sensor circuit.





NG

2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)

OK

2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
a.


OK

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the CKP sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D54-1 - D2-122 (NE+) Always Below 1 Ω
D54-2 - D2-121 (NE-) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
D54-1 or D2-122 (NE+) - Body ground Always 10 kΩ or higher
D54-2 or D2-121 (NE-) - Body ground Always 10 kΩ or higher




OK

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
B319222E13
0.469,1.771 0.74,1.969 0.271,0.198 10 OK 2.667,1.771 2.948,1.969 0.281,0.198 10 NG 1.719,1.552 2.396,1.76 0.677,0.208 10 Clearance

a.

Check the CKP sensor installation.

OK:

Sensor is installed correctly.




OK

5.CHECK CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)

NG

SECURELY REINSTALL SENSOR

5.CHECK CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)
a.

Check the teeth of the sensor plate.

OK:

Sensor plate does not have any cracks or deformation.




OK

6.REPLACE CRANKSHAFT POSITION SENSOR

NG

REPLACE CRANKSHAFT POSITION SENSOR PLATE

6.REPLACE CRANKSHAFT POSITION SENSOR
a.

Replace the crankshaft position sensor (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>REMOVAL).



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS
7.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Turn the engine switch off and wait for at least 30 seconds.


e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTCs.

Result
Result Proceed to
DTC is not output A
DTC P0335 or P0339 is output B


HINT:

If the engine does not start, replace the ECM.



A

END

B