Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P0724  Brake Switch "B" Circuit High  


DESCRIPTION

The stop light switch is part of a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. This DTC indicates that the stop light switch remains on. When the stop light switch remains on during "STOP and GO" driving, the ECM interprets this as a fault in the stop light switch. Then the ECM illuminates the MIL and the ECM stores the DTC.

DTC No. DTC Detection Condition Trouble Area
P0724 The stop light switch remains on even when the vehicle repeats 5 cycles of STOP (less than 3 km/h [1.86 mph]) and GO (30 km/h [18.65 mph] or more) (2 trip detection logic).
·

Short in stop light switch signal circuit

·

Stop light switch

·

ECM



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Using the GTS, the Data List item "Stop Light Switch" and "ST1" can be read (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).



PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.


d.

Read the values displayed on the GTS.


OK:
Item Measurement Item / Range (display) Normal Condition
Stop Light Switch Stop light switch status:
ON or OFF
·

ON: Brake Pedal is depressed

·

OFF: Brake Pedal is released





OK

NG

2.CHECK STOP LIGHT SWITCH INSTALLATION
2.CHECK STOP LIGHT SWITCH INSTALLATION
a.

Check the stop light switch installation.

OK:

Stop light switch is installed correctly.




OK

3.CHECK TERMINAL VOLTAGE (STP VOLTAGE)

NG

SECURELY REINSTALL STOP LIGHT SWITCH

3.CHECK TERMINAL VOLTAGE (STP VOLTAGE)
a.
U188273E02
1.865,3.656 2.75,3.479 true 1.771,3.667 0.542,3.771 true 1.781,0.063 2.552,0.406 0.771,0.344 10 false Brake Pedal Released 0.229,0.063 1,0.385 0.771,0.323 10 false Brake Pedal Depressed 0.073,2.104 1.302,2.281 1.229,0.177 10 false Wire Harness Side 1.167,2.552 2.177,2.729 1.01,0.177 10 false ECM Connector 2.813,3.385 3.104,3.563 0.292,0.177 10 false STP 0.146,3.688 0.469,3.865 0.323,0.177 10 false ST1- 1.375,4.156 2.052,4.333 0.677,0.177 10 false Front View 0.417,2.719 0.625,2.896 0.208,0.177 10 false A7

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-36 (STP) - Body ground Brake pedal released Below 1.5 V
Brake pedal depressed 7.5 to 14 V




OK

NG

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)
4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)
a.

Disconnect the stop light switch connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A37-2 (OUT) or A7-36 (STP) - Other terminals Always 10 kΩ or higher




OK

REPLACE STOP LIGHT SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR