Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P0011  Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)  P0012  Camshaft Position "A" - Timing Over-Retarded (Bank 1)  


DESCRIPTION

Refer to DTC P0010 (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>P0010).

DTC No. DTC Detection Condition Trouble Area
P0011 Intake valve timing is stuck at a certain value when in the advance range (1 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve

·

Oil control valve filter

·

Camshaft timing gear assembly

·

ECM


P0012 Intake valve timing is stuck at a certain value when in the retard range (2 trip detection logic).

MONITOR DESCRIPTION

The ECM optimizes the intake valve timing using the Variable Valve Timing (VVT) system to control the intake camshaft. The VVT system includes the ECM, the camshaft timing oil control valve and the VVT controller (camshaft timing gear assembly). The ECM sends a target duty-cycle control signal to the camshaft timing oil control valve assembly. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake camshaft.

If the difference between the target and actual intake valve timing is large, and changes in the actual intake valve timing are small, the ECM interprets this as a VVT controller stuck malfunction and stores a DTC.


DTC P0011 (Advanced Camshaft Timing) is subject to 1 trip detection logic.

DTC P0012 (Retarded Camshaft Timing) is subject to 2 trip detection logic.

These DTCs indicate that the VVT controller cannot operate properly due to a camshaft timing oil control valve malfunction or the presence of foreign objects in the camshaft timing oil control valve.


CONFIRMATION DRIVING PATTERN

A384199E02
3.708,3.427 3.865,3.427 3.865,3.427 4.135,2.646 false 6.177,3.354 6.333,3.354 6.333,3.354 6.688,2.625 false 2.458,0.063 6.969,0.99 4.51,0.927 10 false *: Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (depress the accelerator pedal by a large amount) and then decelerating the vehicle 10 to 15 times. 0.208,0.469 1.146,0.813 0.938,0.344 10 false Vehicle Speed 0.208,1.094 1.115,1.469 0.906,0.375 10 false Approximately 60 km/h 0.719,2.115 1.427,2.49 0.708,0.375 10 false Idling 0.188,2.365 1.094,2.76 0.906,0.396 10 false Engine Switch on (IG) 1.375,2.354 2.083,2.729 0.708,0.375 10 false [A] 1.615,2.771 2.438,3.115 0.823,0.344 10 false Warming up 2.563,2.781 3.813,3.052 1.25,0.271 10 false 10 minutes or more 2.542,3.333 3.896,3.625 1.354,0.292 10 false 3 minutes or more 1.865,2.042 2.573,2.417 0.708,0.375 10 false [B] 2.99,1.021 3.698,1.396 0.708,0.375 10 false [C] 4.021,2.333 4.729,2.708 0.708,0.375 10 false [D] 4.25,3.167 4.604,3.417 0.354,0.25 10 false [E] 5.458,2.25 5.813,2.5 0.354,0.25 10 false [F]* 6.583,2.323 6.938,2.573 0.354,0.25 10 false [G] 6.823,3.167 7.094,3.417 0.271,0.25 10 false [H] 5.021,3.271 6.375,3.563 1.354,0.292 10 false 3 minutes or more

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the engine switch off and wait for at least 30 seconds.

5.

Turn the engine switch on (IG) and turn the GTS on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

7.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Idle the engine for 3 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0011 or P0012.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [F] through [H].



14.

Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 10 to 15 times [F].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Depress the accelerator pedal by a large amount.


15.

Idle the engine for 3 minutes or more [G].

16.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [H].

17.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



18.

Check the DTC judgment result again.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

DTC P0011 or P0012 may be stored when foreign matter in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. That foreign matter may then be captured by the oil filter.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011 OR P0012)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
P0011 or P0012 is output A
P0011 or P0012 and other DTCs are output B

HINT:

If any DTCs other than P0011 or P0012 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (OPERATE OIL CONTROL VALVE)

B

2.PERFORM ACTIVE TEST USING GTS (OPERATE OIL CONTROL VALVE)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Turn the A/C switch on.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1).


f.

Check the engine speed while operating the camshaft timing oil control valve using the GTS.

OK
GTS Operation Specified Condition
0% Normal engine speed
100% Engine idles roughly or stalls



OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)

NG

4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG).


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


k.

Read the pending DTCs.

Result
Result Proceed to
DTC is not output A
DTC P0011 or P0012 is output B

HINT:

DTC P0011 or P0012 may be stored when foreign matter in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. That foreign matter may then be captured by the oil filter.




A

B

4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)
4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)
a.
A098345E31
2.167,2.313 2.625,2.396 true 1.083,0.698 1.76,0.344 1.76,0.344 2.583,0.667 true 1.083,1.229 1.781,1.677 1.781,1.677 2.573,1.031 true 1.26,0.01 2.198,0.229 0.938,0.219 10 false Timing Mark 1.302,1.677 2.177,1.885 0.875,0.208 10 false Timing Mark 2.677,2.292 3.188,2.469 0.51,0.177 10 false Groove

Remove the cylinder head cover.


b.

Turn the crankshaft pulley, and align its groove with the timing mark "0" on the timing chain cover.


c.

Check that the timing marks on the camshaft timing sprocket and camshaft timing gear are facing upward as shown in the illustration.

If not, turn the crankshaft 1 revolution (360°), then align the marks as above.


OK:

Timing marks on camshaft timing gears are aligned as shown in the illustration.




OK

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE

NG

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE

OK

6.INSPECT OIL CONTROL VALVE FILTER

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE

6.INSPECT OIL CONTROL VALVE FILTER
A098169E13
1.49,0.927 1.625,1.333 false 0.781,0.813 1.49,1 0.708,0.188 10 false OCV Filter

a.

Remove the oil control valve filter.


b.

Check that the filter is not clogged.

OK:

Filter is not clogged.




OK

7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

NG

REPLACE OIL CONTROL VALVE FILTER

7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
a.

Replace the camshaft timing gear assembly (See page Engine / Hybrid System>2AZ-FE ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY).



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG).


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


k.

Read the pending DTCs.

Result
Result Proceed to
DTC is not output A
DTC P0011 or P0012 is output B



A

END

B