Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P0037  Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)  P0038  Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)  


DESCRIPTION


HINT:
·

Sensor 2 refers to the sensor mounted behind the Three-Way Catalytic Converter (TWC) and located far from the engine assembly.

·

When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the Heated Oxygen (HO2) sensor heater in fail-safe mode. Fail-safe mode continues until the engine switch is turned off.

·

The HO2 sensor heater circuit uses a relay on the +B side of the circuit.

A140671E02
0.117,0.076 2.866,0.265 2.749,0.188 10 Reference (System Diagram of Sensor 2) 1.278,0.878 1.511,1.059 0.233,0.181 10 EFI 2.099,0.632 2.746,0.813 0.647,0.181 10 EFI MAIN 3.377,0.386 4.957,0.568 1.580,0.181 10 Heated Oxygen Sensor 3.457,1.017 3.647,1.198 0.191,0.181 10 +B 4.55,1.024 4.930,1.205 0.380,0.181 10 HT1B 3.457,1.588 3.685,1.769 0.229,0.181 10 E2 4.55,1.595 4.977,1.776 0.427,0.181 10 OX1B 3.885,0.842 4.320,1.023 0.436,0.181 10 Heater 3.871,1.432 4.330,1.614 0.459,0.181 10 Sensor 5.874,0.365 6.200,0.547 0.326,0.181 10 ECM 5.138,1.024 5.518,1.205 0.380,0.181 10 HT1B 5.138,1.595 5.539,1.776 0.401,0.181 10 OX1B 5.138,2.166 5.527,2.347 0.389,0.181 10 EX1B 5.138,2.733 5.541,2.914 0.403,0.181 10 MREL 0.494,1.043 0.985,1.403 0.492,0.360 10 From Battery



DTC No. DTC Detection Condition Trouble Area
P0037 Heated Oxygen (HO2) sensor heater current is less than the specified value while the heater is operating
(1 trip detection logic)
·

Open or short in HO2 sensor heater circuit

·

HO2 sensor (sensor 2)

·

ECM


P0038 Heated Oxygen (HO2) sensor heater current is specified value or higher while the heater is operating
(1 trip detection logic)
·

Short in HO2 sensor heater circuit

·

HO2 sensor (sensor 2)

·

ECM



MONITOR DESCRIPTION

The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature, and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.

Heated Oxygen Sensor Heater Range Check (P0037 or P0038):

The ECM monitors the current applied to the heated oxygen sensor heater to check the heater for malfunctions.

If the heater current is outside the normal range, the signal transmitted by the heated oxygen sensor becomes inaccurate. When the current in the heated oxygen sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.



WIRING DIAGRAM

CONFIRMATION DRIVING PATTERN

A262623E36
0.813,0.969 1.604,1.26 0.792,0.292 10 false 3000 rpm 1.031,1.74 1.552,1.99 0.521,0.25 10 false Idling 0.271,2.052 1.458,2.427 1.188,0.375 10 false Engine Switch on (IG) 1.927,2.156 2.24,2.396 0.313,0.24 10 false [A] 2.76,1.646 3.146,1.958 0.385,0.313 10 false [B] 4.021,0.885 4.323,1.167 0.302,0.281 10 false [C] 5.385,1.635 5.729,1.875 0.344,0.24 10 false [D] 2.281,2.583 3.479,2.74 1.198,0.156 10 false 5 minutes or more 4.875,2.604 6.083,2.813 1.208,0.208 10 false 5 minutes or more 3.854,2.615 4.458,2.854 0.604,0.24 10 false 1 minute 5.979,3.031 6.281,3.24 0.302,0.208 10 false [E]

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the engine switch off and wait for at least 30 seconds.

5.

Turn the engine switch on (IG) and turn the GTS on [A].

6.

Start the engine and idle it for 5 minutes or more [B].

7.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].

8.

Idle the engine for 5 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0037 or P0038.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.




CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Change the fuel injection volume using the Control the Injection Volume for A/F Sensor function provided in the Active Test and monitor the heated oxygen sensor output voltage (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>P0136). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



PROCEDURE

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

OK

2.CHECK TERMINAL VOLTAGE (+B OF HO2 SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (+B OF HO2 SENSOR)
a.
A394017E01
0.583,1 1,1.25 0.417,0.25 1.844,1.146 2.208,0.948 false 0.104,0.083 1.615,0.365 1.51,0.281 10 false Wire Harness Side 0.552,0.448 2.938,0.688 2.385,0.24 10 false Heated Oxygen Sensor Connector 0.656,1.031 0.969,1.229 0.313,0.198 10 false D59 0.51,1.333 1.125,1.594 0.615,0.26 10 false Sensor 2 1.385,1.729 2.292,1.969 0.906,0.24 10 false Front View 2.26,0.844 2.573,1.042 0.313,0.198 10 false +B

Disconnect the HO2 sensor connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D59-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (HO2 SENSOR - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (HO2 SENSOR - EFI MAIN RELAY)

3.CHECK HARNESS AND CONNECTOR (HO2 SENSOR - ECM)
a.

Disconnect the HO2 sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D59-1 (HT1B) - D2-47 (HT1B) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
D59-1 (HT1B) or D2-47 (HT1B) - Body ground Always 10 kΩ or higher




OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTCs.

Result
Result Proceed to
DTC is not output A
DTC P0037 or P0038 is output B



A

B