Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › 2013.04–2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P0500  Vehicle Speed Sensor "A"  


DESCRIPTION

Vehicles, which are equipped with ABS (Anti-lock Brake System), detect the vehicle speed using the skid control ECU and wheel speed sensor. The wheel speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of the pulse signal.

A079413E73
2.667,0.563 3.417,0.781 0.75,0.219 10 false 4-Pulse 4.719,0.563 5.469,0.781 0.75,0.219 10 false 4-Pulse 1.583,1.135 2.115,1.333 0.531,0.198 10 false ECU 5.771,1.146 6.302,1.344 0.531,0.198 10 false ECM 1.583,0.969 2.583,1.167 1,0.198 10 false Skid Control 0.24,1.177 1.375,1.604 1.135,0.427 10 false From Wheel Speed Sensor 3.375,1.781 5.156,1.979 1.781,0.198 10 false Combination Meter

DTC No. DTC Detection Condition Trouble Area
P0500 for CVT models:
Either of the following conditions (a) and (b) is met for 2.0 seconds or more
(1 trip detection logic)
(a) Transmission revolution sensor signal output is 1000 rpm or more
(b) No vehicle speed sensor signal to ECM
for A/T models:
Either of the following conditions (A) and (B) are met
(1 trip detection logic)
(A) Either of the following conditions 1or 2 is met
1.

All of the following conditions (a), (b) and (c) are met

(a)

Engine coolant temperature is 20°C (68°F) or more

(b)

Engine coolant temperature sensor malfunction is not detected

(c)

Time after NSW input signal on to off is 2 seconds or more


2.

All of the following conditions (a), (b) and (c) are met

(a)

Engine coolant temperature is less than 20°C (68°F)

(b)

Engine coolant temperature sensor malfunction is detected

(c)

Time after NSW input signal on to off is 30 seconds or more



(B) While vehicle is being driven, no vehicle speed sensor signal is sent to ECM
·

Open or short in speed signal circuit

·

Combination meter assembly

·

ECM

·

Skid control ECU

·

Vehicle speed sensor



WIRING DIAGRAM

A127263E34
0.543,1.793 1.714,1.957 1.170,0.164 10 Skid Control ECU 2.191,0.81 4.094,1.020 1.904,0.210 10 Combination Meter Assembly 2.191,0.642 2.492,0.852 0.302,0.210 10 G28 2.441,1.682 2.597,1.863 0.156,0.181 10 SI 3.626,1.682 3.816,1.863 0.191,0.181 10 +S 3.92,1.682 4.111,1.863 0.191,0.181 10 40 5.048,1.682 5.148,1.863 0.100,0.181 10 8 5.857,0.838 6.182,1.019 0.326,0.181 10 ECM 5.576,0.838 5.786,1.019 0.210,0.181 10 A7 5.233,1.646 5.535,1.827 0.303,0.181 10 SPD 5.991,1.336 6.295,1.496 0.304,0.160 10 5 V 2.155,1.689 2.345,1.870 0.191,0.181 10 39

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OPERATION OF SPEEDOMETER
a.

Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

HINT:
·

The vehicle speed sensor is operating normally if the speedometer reading is normal.

·

If the speedometer does not operate, check it by following the procedure described in speedometer malfunction (see page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speedometer Malfunction).





OK

2.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)

NG

GO TO MALFUNCTION IN SPEEDOMETER

2.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester ON.


c.

Enter the following menus: Powertrain / Engine and ECT/ Data List / Vehicle Speed.


d.

Drive the vehicle.


e.

Read the value displayed on the tester.

OK:

Vehicle speeds displayed on tester and speedometer display are equal.




NG

3.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)

OK

3.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)
a.
U188517E01
0.077,0.051 1.334,0.261 1.257,0.210 10 Wire Harness Side 1.678,4.251 2.537,4.400 0.859,0.149 10 Turn Wheel 0.057,2.706 0.675,2.855 0.618,0.149 10 5 to 12 V 0.32,4.125 0.578,4.274 0.257,0.149 10 0 V 0.561,1.998 0.814,2.147 0.253,0.149 10 +S 0.838,1.449 0.673,1.952 false 0.871,0.537 2.767,0.747 1.896,0.210 10 Combination Meter Connector 0.392,0.534 0.713,0.697 0.320,0.163 10 G28

Shift the transmission gear selector lever to the neutral position.


b.

Jack up the vehicle.


c.

Turn the engine switch on (IG).


d.

Measure the voltage between the terminal of the combination meter and the body ground while the front wheel is turned slowly.

Standard voltage:
Tester Connection Specified Condition
G28-40 (+S) - Body ground Voltage generated intermittently


HINT:

The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.




OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

NG

REPLACE COMBINATION METER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (check for open):
Tester Connection Condition Specified Condition
G28-40 (+S) - A7-8 (SPD) Always Below 1 Ω



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (check for short):
Tester Connection Condition Specified Condition
G28-40 (+S) or A7-8 (SPD) - Body ground Always 10 kΩ or higher


HINT:

Because the speed signal is used by other systems, it is possible that a short in the speed signal circuit could cause other systems to malfunction.




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR