This Electronic Throttle Control System (ETCS) does not use a throttle cable.
These DTCs relate to the accelerator pedal position sensor.
The Accelerator Pedal Position (APP) sensor is built into the accelerator pedal sensor assembly and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type sensor and uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds. The voltage, which is applied to terminals VPA and VPA2 of the ECM, varies between 0.5 V and 4.5 V in proportion to the operating angle of the accelerator pedal (throttle valve). A signal from VPA indicates the actual accelerator pedal opening angle (throttle valve opening angle) and is used for engine control. A signal from VPA2 conveys the status of the VPA circuit and is used to check the accelerator pedal position sensor itself.
The ECM monitors the actual accelerator pedal opening angle (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P2120 | VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic) | ·
Accelerator Pedal Position (APP) sensor ·
ECM |
| P2122 | VPA 0.4 V or less for 0.5 seconds or more when accelerator pedal depressed (1 trip detection logic) | ·
APP sensor ·
Open in VCPA circuit ·
Open or ground short in VPA circuit ·
ECM |
| P2123 | VPA 4.8 V or more for 2.0 seconds or more
(1 trip detection logic) |
·
APP sensor ·
Open in EPA circuit ·
ECM |
| P2125 | VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic) | ·
APP sensor ·
ECM |
| P2127 | VPA2 1.2 V or less for 0.5 seconds or more when accelerator pedal depressed (1 trip detection logic) | ·
APP sensor ·
Open in VCP2 circuit ·
Open or ground short in VPA2 circuit ·
ECM |
| P2128 | Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic):
(a) VPA2 4.8 V or more (b) VPA between 0.4 V and 3.45 V |
·
APP sensor ·
Open in EPA2 circuit ·
ECM |
| P2138 | Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic):
(a) Difference between VPA and VPA2 0.02 V or less (b) VPA 0.4 V or less and VPA2 1.2 V or less |
·
Short between VPA and VPA2 circuits ·
APP sensor ·
ECM |
When any of these DTCs are output, check the accelerator pedal position sensor voltage using the intelligent tester. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.
| Trouble Area | Accelerator Pedal Fully Released | Accelerator Pedal Fully Depressed | ||
|---|---|---|---|---|
| Accel Sensor Out No. 1 | Accel Sensor Out No. 2 | Accel Sensor Out No. 1 | Accel Sensor Out No. 2 | |
| Open in VCP circuit | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V |
| Open or ground short in VPA circuit | 0 to 0.2 V | 1.2 to 2.0 V | 0 to 0.2 V | 3.4 to 4.75 V |
| Open or ground short in VPA2 circuit | 0.5 to 1.1 V | 0 to 0.2 V | 2.6 to 4.5 V | 0 to 0.2 V |
| Open in EPA circuit | 4.5 to 4.98 V | 4.5 to 4.98 V | 4.5 to 4.98 V | 4.5 to 4.98 V |
| Normal condition | 0.5 to 1.1 V | 1.2 to 2.0 V | 2.6 to 4.5 V | 3.4 to 4.75 V |
Accelerator pedal positions are expressed as voltages.
When DTC P2120, P2121, P2122, P2123, P2125, P2127, P2128 or P2138 is stored, the ECM enters fail-safe mode. If either of the 2 sensor circuits malfunctions, the ECM uses the remaining circuit to calculate the accelerator pedal position to allow the vehicle to continue driving. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.
Fail-safe mode continues until a pass condition is detected, and the engine switch is turned off.
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.
Read the value displayed on the tester.
| Accelerator Pedal Operation | Accel Sensor Out No. 1 | Accel Sensor Out No. 2 |
|---|---|---|
| Fully Released | 0.5 to 1.1 V | 1.2 to 2.0 V |
| Fully Depressed | 2.6 to 4.5 V | 3.4 to 4.75 V |
NG
OK
Disconnect the Accelerator Pedal Position (APP) sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A3-6 (VPA) - A7-55 (VPA) | Always | Below 1 Ω |
| A3-5 (EPA) - A7-59 (EPA) | ||
| A3-4 (VCPA) - A7-57 (VCPA) | ||
| A3-3 (VPA2) - A7-56 (VPA2) | ||
| A3-2 (EPA2) - A7-60 (EPA2) | ||
| A3-1 (VCP2) - A7-58 (VCP2) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A3-6 (VPA) or A7-55 (VPA) - Body ground | Always | 10 kΩ or higher |
| A3-5 (EPA) or A7-59 (EPA) - Body ground | ||
| A3-4 (VCPA) or A7-57 (VCPA) - Body ground | ||
| A3-3 (VPA2) or A7-56 (VPA2) - Body ground | ||
| A3-2 (EPA2) or A7-60 (EPA2) - Body ground | ||
| A3-1 (VCP2) or A7-58 (VCP2) - Body ground |
OK
NG
Disconnect the APP sensor connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A3-4 (VCPA) - A3-5 (EPA) | Engine switch on (IG) | 4.5 to 5.5 V |
| A3-1 (VCP2) - A3-2 (EPA2) |
OK
NG
Replace the accelerator pedal sensor assembly (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL).
NEXT
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Clear the DTCs (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG).
Turn the tester on.
Fully depress and release the accelerator pedal.
Check that 5 seconds or more have elapsed since the engine switch is turned on (IG).
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138 are output | A |
| DTC is not output | B |
A
B